Search Documents

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south- eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States. Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). [ ] The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1939

By R. R. Unterberger

Three different physical techniques have been used to see through or probe into rocks, so miners might know what is ahead or overhead. These are radar, sonar, and a unique type of sonar called nonlinear sonar. Five radar systems have been developed. The highest frequency used is 4300 MHz for detecting small fractures at close range. This gives the best resolution. For longest range (over 2000 m, or 6560 ft) we use the 30 MHz radar for finding faults ahead of mining or ranging to salt dome flanks. Two types of salt, dome and bedded, are recognized. Radar works well in dry (dome) salt, but not in bedded salt which contains small amounts of water. The dipole moment of water absorbs energy from the radar. Thus was born the 30 MHz radar system and sonar probing systems. These can probe to 100 m (328 ft) even into wet salt. All probing systems measure data in time, which are converted to distance by measuring the time of travel of radar or sonar through salt pillars of known thickness. Ranges of probing in salt are from less than 1 m (3.3 ft) to more than 2000 m (6560 ft). Uses of radar and sonar probing in mines include mapping the top of salt above a mine; mapping salt dome flanks; finding impurities in salt such as anhydrite, sandstone, or potash stringers; locating old boreholes in salt pillars; locating fractures in salt; and finding faults or water zones ahead of mining.

Jan 1, 1985

By C. W. Davis, R. S. Dean

AMONG naturally occurring inorganic compounds, magnetite has many unusual and interesting properties, and it is the purpose of this paper to call attention to these properties and review possible uses of magnetite that might be based on them; in other words, to see what uses may be found for magnetite as a physical rather than as a chemical entity, as a mineral rather than as an iron ore. The Mineral Physics Studies initiated in the Metallurgical Division of the U. S. Bureau of Mines a few years ago gathered together much information on mineral properties, and they are therefore the principal source of material for this paper. Magnetic Properties Of Magnetite And Possible Uses As A Magnetic Material Magnetite is unique among minerals for its great magnetic susceptibility, approximately one-third that of soft iron, and some magnetites are permanent magnets, or lodestones. The literature contains many measurements of magnetic properties of individual magnetite crystals, but no systematic survey of the effect of mechanical preparation and heat-treatment was available until the recent investigations of the Bureau of which included not only susceptibility but coercive force and remanence as well. For the purpose of orientation, Table 1 gives the magnetic properties of several samples of magnetite and of a few other substances3. This table indicates that when ordinary magnetite is powdered it decreases in susceptibility and increases in coercive force and remanence, approaching the properties of lodestone. The properties of lodestone are in fact probably due to the development of very large internal surface on fine grain size4.

Jan 1, 1937

By Om P. Garg

During the period between 1970 and 1974 the Iron Ore Company of Canada had embarked on a detailed program to evaluate all aspects of mine design work for its open pit mines around Schefferville, located both in Quebec and Labrador, Newfoundland, Canada. One of the main conclusions was that the majority of the slope angles for the ultimate pit walls could be steeped. During the period 1975 and 1976,five (5) open pit iron ore mines were redesigned using the steeper slope angles up to 55 degrees. Initially these pits were designed at slope angles varying between 37 degrees and 45 degrees due to the generally fractured and leached nature of rocks in the area. During the active mining phase between 1976 and 1979, the stability of the steeper ultimate pit walls was monitored. The mining of ore was successfully completed in 1978 and 1979 in three pits. This of course, resulted in a significant savings due to a reduction in the quantity of waste that had to be removed. The successful pit slope redesign project was a co-operative effort between the Federal Government, Universities and the Iron Ore Company of Canada.

Jan 1, 1983

By R. E. Lindstrom, D. G. Peterson, H. J. Heinen

Alkaline alcohol solutions were investigated by the Federal Bureau of Mines for improving the desorption rate of gold and silver from metal-laden activated carbon generated in gold processing circuits. Factors affecting the desorption, such as temperature, alcohol content, type of alcohol, and alkalinity, were studied. Nearly complete metal desorption was obtained in 5 to 6 hr at 80º C using a solution containing about 20 vol-pct alcohol and 1 pct sodium hydroxide. Sodium sulfide was shown to be effective for selectively precipitating silver from the carbon strip solutions, thereby providing a means for producing high- purity gold by subsequent electrolysis.

Jan 1, 1976

By O. B. Buchlen, J. W. Smith

The Coal Research Bureau of the School of Mines at West Virginia University, using an experimental flotation cell designated an airlift-cyclone was able to obtain a clean coal product containing 7.64% ash with 94% yield and 97% coal recovery. This favorable performance was obtained with the experimental flotation cell operating as a simulated three-stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient operation on high density feed slurry, and absence of moving parts. The primary shortcoming of the experimental cell is its limited capacity. The Coal Research Bureau presently has under construction a larger unit which, it is hoped, will provide the capacity and quality to establish the airlift-cyclone as a commercially feasible unit. Froth flotation of fine coal is a practice which has only recently gained wide acceptance in this country. Various explanations can be put forth for this delayed acceptance of a very selective and efficient system of coal preparation. Among these reasons would be the advent of continuous mining machines resulting in the increased production of coal fines, the change in market patterns from domestic and rail consumers who did not want fines to a predominantly utility market which normally consumes fines, and also the imposition of legal restrictions in regard to stream pollution. However, the major detriment is probably the high cost involved both in installation and operation of the flo- tation unit and auxiliary systems. These facts assume greater emphasis when considering that froth flotation installations normally process a low quality feed product. A recent estimate' of installation costs including dryers, filters, and other auxiliary equipment for a flotation system was $5000 to $7000 per ton of capacity while the operating costs, exclusive of auxiliary equipment, were estimated at 10 to 306 per ton of feed. The Coal Research Bureau of the School of Mines at West Virginia University is currently developing a simplified froth flotation cell, designated an airlift-cyclone, which may provide considerable savings in capital and operating costs without sacrificing product quality or recovery. This experimental cell consists of three primary components: 1) a vertically mounted U-shaped pipe; 2) an air injector device; and 3) an integrally mounted cyclone-like unit (Fig. 1). A feed slurry is introduced at the top of one leg of the U-pipe while compressed air is injected near the base of the other leg. The air serves both to aerate the pulp and to cause it to flow upward into the base of the cyclone unit where the floated clean coal is separated from the reject material and unfloated coal which remains in slurry. The Coal Research Bureau's experimental airlift-cyclone is somewhat similar in principle to a flotation device developed by Russian engineers in the late 1950's. In tests upon a two-stage pilot-size device, the Russians obtained very favorable cleaning efficiencies.' However, later experience with production models demonstrated that rated capacities and acceptable product quality could not always be maintained.3 Because of these limitations, Russian engineers subsequently recommended that conventional, mechanical cells be used when cleaning difficult to float slurries. Engineers at the Coal Research Bureau felt that such a device utilizing the combined actions of a cyclone and a froth flotation machine offered numerous attractive features and merited investigation. Accordingly, a small capacity experimental airlift-cyclone was designed and, with the permission of the Christopher Coal Company Div. of Consolidation Coal Co., installed in Christopher's Humphrey preparation plant near Morgantown, West Virginia.

Jan 1, 1964

By T. L. Joseph, G. Bitsianes

The gaseous reduction of dense iron ore is a topochemical process in which reduction takes place at distinct interfaces between solid phases or layers. Under normal conditions, these interfaces remain parallel to the exterior surface of the ore body as they move inward. Certain conditions, such as cracking, high porosity, impurities, entrapped residual oxides, may cause departures from normal topochemical behavior. THE gaseous reduction of dense iron ore proceeds at interfaces between several solid phases or layers.',' Under normal conditions, these interfaces progress inward and remain parallel to the exterior surface of the ore body. This topochemical behavior is clearly illustrated in Fig. 1 which shows partially reduced specimens of natural and synthetic hematite. Using a coordinated sequence of macro, micro, and X-ray examinations, the authors1-'2 found that the number of interfaces and participating phases was in agreement with the Fe-0 system. Above 570°C, reduction of the ore involved a maximum of three common boundaries between four solid phases: iron, wiistite (Fe,O), magnetite (Fe,O,), and hematite (Fe,O,). Below 570°C, reduction proceeded through two interfaces between three phases: iron, magnetite (Fe,O,), and hematite (Fe,O,). The decrease in the number of phases below 570°C was due to the instability of wiistite below this temperature. The sequence of phases was also consistent with the equilibrium requirements. For example, the layers of iron oxides that were formed in topochemical fashion were always orientated in the order of increasing oxygen content. Thus, in Fig. 1 an outer layer of metallic iron is followed in turn by a thick intermediate band of black wiistite, by a thin layer of light magnetite, and finally by a relatively large core of hematite. This arrangement of the oxide layers was due to restrictions in reducing conditions which were imposed by the physical structure of the solid. The highly reducing gas on the outside of the particle gradually lost its reducing power as it penetrated into the specimen. On a macro scale, the layers of the various oxides appeared to be sharply defined and uniform in composition. Microexamination of the sections, however, revealed that the interfaces did possess measurable widths which varied with the porosity and chemical activity of the oxide phase undergoing reduction. For example, Fig. 2 shows three interfaces in a dense hematitic ore which was partially reduced at 850°C. At the iron-wiistite interface where the greatest porosity developed, the reaction proceeded over a zone 25 to 30 microns in width. Toward the interior, the interfaces became progressively narrower until at the magnetite-hematite boundary the reaction zone was about 1 micron wide. In this region the structure was exceedingly dense; the hematite possessing a porosity on the order of 3 pct. A careful micro study across polished layers of the various oxides revealed generally homogenous and single-phase structures. As reported in a previous paper,' the wiistite layer was characterized by an increase in oxygen content with depth of penetration. The topochemical behavior of reduction was studied in six types of ore of different origin, composition, and physical structure. In most cases, reduction proceeded at the boundaries of well defined layers or phases, and this behavior may be regarded as normal for most dense fine grained ores. Deviations from Ideal Topochemical Behavior A number of deviations from the normal topochemical behavior were noted. In these cases, the continuity of the reduction interfaces was disrupted in one of four ways: 1—Cracking of the specimen interrupted the geometric configuration, and the interfacial advance was no longer parallel to the exterior surface. 2—As a result of high porosity, the interfaces were spread over an appreciable distance and all but obliterated. 3—Impurities in the ore promoted a variety of deviations, including cracking. 4—A residual oxide phase was entrapped in the reaction product and left behind the advancing macro interface. Results from Cracking: A crack leading into the interior of an ore specimen presents a path of least resistance for the counter-flow of reducing gases and gaseous reduction products. Higher reducing conditions can be maintained along such cracks and reduction accordingly will propagate well ahead of the normally advancing reduction interfaces. Cracking was caused by a number of factors, one of which was the thermal spalling of impurities in the massive form. A more general type of cracking was due to reduction and was found in all dense varieties of natural and synthetic hematite, particularly in the temperature range of 500" to 700°C. The effect is shown clearly in Fig. 3. In this case, a dense sphere of pure hematite was partially reduced at 650°C for 100 min. The macrosection shows that one large reduction crack had penetrated the specimen and disrupted the normal topochemical advance of the interfaces. The outer layer of iron was only slightly affected but the thin dark layer of wiistite, adjacent to the ferrite, had widened perceptibly as it progressed along the crack. Farther inward, the magnetite layer was greatly disrupted and had penetrated irregularly to form islands of unaltered white hematite. A great deal of internal cracking is evident in the magnetite phase. From a practical point of view, the cracking of dense ores in the blast furnace could lead to desirable as well as undesirable effects. The general result

Jan 1, 1956

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

All pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process,9-11 but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver's Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open- circuit roughing and closed-circuit roughing are best defined by the diagrams.

Jan 12, 1958

By H. H. Evinger, M. Muskat

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

H. H. Bleakney (Dept. of Mines and Technical Surveys, Ottawa, Canada)— The work of Dr. Machlin and his colleagues at Columbia University is so scholarly that one hesitates to take issue with them. Nevertheless the writer feels compelled to enter a demurrer to the mechanism of intercrystalline cracking proposed in this paper. The principal obstacle to its acceptance is found in its preoccupation with purely mechanical influences and its disregard for the chemical effect of impurities. The writer believes that the destruction of metallic cohesion by concentration of impurities at the grain boundaries is a necessary and sufficient condition for the development of intercrystalline cracking; and he believes that discussion of the numerous mechanical explanations proposed should wait until some valid objection to the chemical hypothesis has been advanced. It is nearly twenty years since Gillett" drew attention to the possibility that the chemical influence of precipitation might be the cause of intercrystalline cracking. As early as 1935, Greenwood'" remarked that grain-boundary precipitation of impurities in lead appeared to promote intercrystalline cracking. Again in 1939, Scott commented as follows on a paper by Thielemann and Parker:'" "There are at least two familiar phenomena that can influence grain-boundary cohesion: 1) intergranular oxidation; and 2) grain boundary precipitation. An important consideration in this work, therefore, is to determine which, if either, of these factors is responsible for the low values of cohesive strength observed." In 1952. the writer presented evidence," some original and some abstracted, which indicated that in copper, silver, aluminum, lead and iron, intergranular cohesion was a function of the purity of the metal. In 1954 Glen, discussing a paper by Ridley and Tapsell14 indicated his belief in a precipitation mechanism for the intercrystalline embrit-tlement of molybdenum steel and suggested that with an absolutely pure metal it would be almost impossible to obtain an intercrystalline crack. This suggestion has

Jan 1, 1959

By William P. Blake

The Rainbow Lode is situated at Walkerville, in the Summit Valley mining district, Silver Bow County, Montana Territory, about one mile from Butte City. It was so named ill 1876 by Mr. J. E. Clayton, in recognition of the broadly-sweeping curve of the outcrop across the rounded surface of the eastern slope of a granitic mountain, at an elevation of about 6000 feet above the sea-level. It is on the western side of the range which divides the waters of the Missouri from those of the Columbia. History.—The history of the district is an instructive one. The water-courses and flanks of the hills were worked for years for placer gold. Millions of dollars' worth of low-grade gold have been washed out of the surface gravels below the veins of the district. Missoula Gulch and Silver Bow creek, just below Butte, are noted for their rich placers, and they continue to yield largely, producing within narrow limits from $50,000 to $100,000 dollars' worth of golddust yearly. It is ragged vein-gold, and evidently is near its parent source. It is no doubt derived from the disintegration of the veins of the district, and this conclusion was soon forced upon the miners. The veins which were seen outcropping boldly upon the slopes above them were located, and prospecting commenced. These outcrops were found heavily stained and blackened with oxide of manganese, and were porous and honey-combed in places, showing that the quartz was formerly filled with pyritous ores, and that these ores had decomposed and dissolved away, leaving, however, portions of the precious metal behind, especially at and near the surface of the ground. Assays of the croppings gave variable and often contradictory results; but the fact. that these were the outcrops of lodes bearing gold and silver in depth was patent to any experienced observer of mineral veins. The lodes of the district were first brought prominently to notice by Mr. Clayton in 1876, and in October of that year the Alice mine, upon the central portion of the lode, was opened by Mr. Marcus Daly, now so well known as the superintendent of the Anaconda Copper mine, upon another extremely interesting lode, in the same region.

Jan 1, 1888

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak's4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis' solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By Richard Downs, Stephen P. Burke

The oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combustion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the conditions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 2H2O + 7O2 ? 2FeSO4 + 2H2SO4 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to disclose any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1938

By P. Chiotti, J. T. Mason

Metallographic, thermal, X-ray, and vapor-pressure data were employed in establishing the Ce-Zn phase diagram. Nine compounds and three eutectics were observed. The eutectic compositions in weight percent zinc and temperatures are 10 pct and 495"C, 37 pct and 795°C, and 56 pct and 810°C. Three of the compounds, CeZn, CeZnn, and CeZne.5, melt congru-ently at 825°, 87.505°, and 980°C, respectively; the other six compounds, CeZns, CeZns.67, CeZn4.5, CeZn5.25, CeZn,, and CeZnll, decompose peritectically at 820°, 840°, 870°, 885", 960°, and 795"C, respectively. The compound CeZn5.25 is an AB5 type with a small range of composition which lies on the zinc-rich side of the 1 to 5 stoichiometry. Zinc vapor-pressure data obtained by the dewpoint method were employed in calczilating the thermodynamic properties of both the liquid alloys and solid compounds. The data for the A critical review of the information available on the Ce-Zn system up to 1960 has been given by K. Gschneidner, Jr.' Of particular interest is the work by J. schramm2 who investigated the region between 55 and 100 wt pct Zn and reported a CeZn,, compound which decomposes peritectically at 785"C, a CeZn, compound which melts congruently at 972"C, and five temperature horizontals at 79@, 817", 840", liquid alloys were fitted to the relation from which the relation was obtained by integration. In these relations F XS is the excess partial molal free energy, N is atom fraction, and the constants c and d have the values c = (-22,000 + 7.0T) and d = 6171,000 + 74.0T). Relations for the standard free energy of formation for the solid compounds were derived from the data. At 973°K the enthalpy in kilocalories per gram-atom z)aries from —11.3 for CeZnz to —8.21 for CeZn~l and the free energy in the same units varies from —7.1 joy CeZn, to -3.82 for CeZn11. and 942°C in the region between 55 and 75 wt pct Zn. No attempt was made to identify other features of the system. I. Johnson and R. yonko3 used a fused-salt cell to measure the electromotive force between pure cerium and an alloy consisting of zinc-rich liquid in equilibrium with CeZnll. Solubility data for cerium in zinc has been reported by J. Knighton et u1 .4 Johnson and Yonko give the following equa-. tions for the mole fraction of cerium in zinc and the standard free energy of formation of CeZnll:

Jan 1, 1965

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

THE first session of the Institute was held in the hall of the Washington University, Wednesday evening, May 27th, President Raymond in the chair. After the address of welcome by Hon. Thomas Allen, and the reply of Mr. Raymond, the following names were presented for election as members and associates, duly indorsed by the Council. They were unanimously elected : *Henry Booth, - New York City. *Charles H. Morgan, - Worcester, Mass. *Howard Painter, - West Chester, Pa. *Dr. M. J. Goodfellow, - Eberhardt, White Pine Co., Nevada *Otto Wittelshach, - Eureka, Nevada. *John T. Williams, - New York City. †Charles A. Young, - Philadelphia. *Charles E. Stafford, - Boston, Mass. *Arnold Hague, - Orange, N. J. *Richard Pearcé, - Black Hawk, Colorado. *W. R. Maffet, - Wilkes-Barre, Pa. *Prof. George A. Koenig, - University of Pa., Philadelphia *Prof. R. Nutting, Jr., - Indianapolis, Indiana. *Edwin Mickley, - Hockendauqua, Pa. *G. C. Broadhead, - St. Louis, Mo. *Dr. Adolph Schmidt, - St. Louis, Mo. *Alexander Leonhard, - St. Louis, Mo. *Edward D. Meier, - St. Louis, Mo. *John W. Meier, - St. Louis, Mo. *Prof. Forrest Shepherd, - St. Louis, Mo. *Edward Walsh, - Pilot Knob, Mo. *George Riggs, - St. Louis, Mo. †Col. Chas. B. Parsons, - Cadet, Mo. † W. A. Scott, - Mine La Motte, Mo. *Prof. Paul Schweitzer, - Columbia, Mo. *William E. Guy, - St. Louis, Mo. †William Harris, - St. Louis, Mo. *Henry Black, - Pittsburgh, Pa. †W. Noyes, - New York City. *W. Lorenz, - Philadelphia. †E. A. Whetmore, - New York City. * Members. †Associates.

Jan 1, 1875

By W. F. Campbell

One of the deepest coal operations today is the Springhill No. 2 mine of Cumberland Railway & Coal Co., subsidiary of Dominion Coal Co. Ltd. Mining is now conducted at a slope distance of 14,000 ft, with 4400 vertical ft of cover. The record of Springhill No. 2 can be said to contain the history of bumps in the Province of Nova Scotia. The Springhill coal field forms part of the Cumberland field of Carboniferous age. There are seven mineable fields in the area, numbered in the order they were discovered. Mining has been carried on in all but the No. 4 and 5 seams, but present operations are confined to the No. 2. Fig. 1 shows a vertical section through the seams. Opened in 1873, No. 2 mine was first worked from parallel slopes driven from the outcrop of No. 2 seam down to the 7700 level. As the mine went deeper, a two-place auxiliary slope was driven from the 6900 level to the present workings. A transfer level at the 7800 connects the main haulage with the auxiliary haulage slope. The No. 2 mine plan is shown in Figs. 2 and 3. The seam is bituminous, averaging 8.5 to 9 ft thick. There is a well defined parting 14 to 16 in. from the roof, and this roof coal is harder than the rest of the seam. Average pitch at the outcrop is 30°; at the 6500 level, 20°; at the 7900 level, 16°; and at the 13,800 level, 10°. Immediate roof and floor strata consist of beds of variable thicknesses of shales, grading to arenaceous shales to shaly sandstones to sandstones. A characteristic of the strata is the appearance and disappearance of sandstone bands, of considerable thickness, over distances of several hundred feet. MINE HISTORY Entrance to No. 2 mine is obtained by three parallel slopes, separated by 100-ft pillars except in the upper portion of the mine where the pillars are smaller. Main haulage levels were originally driven 600 ft apart for room and pillar extraction. A parallel drainage and intake airway was driven below each haulage level and a parallel return airway (counter level) above. Pillars 80 to 100 ft wide separated these two servicing entries from the center haulage level. Inclines up to 700 ft apart were driven off the levels up pitch to the upper levels, and at 40-ft centers level rooms 12 ft wide were driven off each side of the inclines, separated by crosscuts every 50 to 100 ft. The rooms were driven up to 350 ft or until they were holed into the room from the adjoining incline—a plan followed until the level reached its boundary. When the entire area between two levels had been divided into pillars, the pillars were extracted from the boundary back to the slope pillars. As depth of cover increased, mining conditions required larger pillars, and at the 3300 level, where NECESSARY PRECAUTIONS FOR MINING AT DEPTH In Room and Pillar Extraction: 1) Pillars must not be too small. 2) Pillar size must be uniform. 3) Extraction lines must be kept as straight and as uniform as possible. If they are irregular they should be brought back into line slowly. 4) Peninsulas of coal surrounded by gob must be avoided. 5) Pillars should not be disturbed after they have been formed. If it is necessary to increase the width of an opening, stripping or ribbing should be done gradually over a long distance. If increased width of openings is necessary at certain locations and can be anticipated, the openings should be widened during development. 6) Under no conditions should small pillars be left in the gob that would interfere with caving. In Long wall Operations: 1) Pillars formed during development for retreating longwalls should be uniform in size and shape. 2) Pillars should not be split after development, but if pillar splitting does become necessary it should not be carried out within the zone influenced by the working faces. 3) Width of levels should not be increased after the levels have been developed. If it does become necessary to widen a level it must be done gradually over a long distance by stripping or ribbing the coal ribs. 4) Extraction lines should remain uniform. If several walls are worked together—one behind the other—a uniform distance must be maintained between them and the wall faces must be kept as straight as possible. If the walls do get out of line, they must be brought back into line gradually to allow for a gradual change in the stress distribution over the area. 5) Stumps of coal, roof supports, etc. must not be allowed to remain in the gob to interfere with caving. 6) Midwalls should be built as rigidly as possible and properly maintained.

Jan 1, 1959