Search Documents

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

The members of the Institute living in the lower Mississippi Valley, I extend a hearty and cordial invitation to their fellow-members to meet with them nest October, in St. Louis. They believe that it will be a meeting of singular interest, inasmuch as the district in question can show in active production almost all of the more useful metals and non-metals. Perhaps too few know that the Southeast Missouri District, about 80 miles south of St,. Louis, and to which a special trip is planned, is the largest lead district in the world. It was that before-the European war, and, now that the production of lead has greatly increased abroad, and has correspondingly increased in the United States, this is one of the most interesting of all lend districts. In 1913, the production of the world was 1,270,000 tons, the last world figures obtainable. In that same year the production of the United States

Jan 5, 1917

By T. M. Geffen, R. E. Gladfelter

Lipson1 has recently presented a technical note wherein theoretical considerations were used to demonstrate. that the adsorption us saturation relation for a linear absorption method is not necessarily a single valued function of saturation.1 It was concluded that the absorption us saturation relationship is subject to the same hysteretic effect as is the flow behavior between the drainage and imbibition systems. It is the purpose of this note to show, by experimental results, that for the manner in which fluids are distributed in porous materials during fluid flow, the relative X-ray absorption us saturation relationship is single-valued regardless of the saturation history. The design of the apparatus used to measure relative X-ray absorption of cores undergoing fluid flow tests is similar to that described by Morgan, McDowell and Doty. A few modifications have been incorporated in the design to increase sensitivity and simplicity of measurement. The sensitivity is such that for usual types of cores a recording pen movement of approximately 12 linear in. is occasioned between the recording of the core dry and when it is completely full of an absorbing liquid, a solution of approximately five per cent by volume of iodo-benzene in a close-cut hydrocarbon fraction, or a solution of 50,000 ppm sodium iodide in water. Two types of experiments were conducted, one in which the liquid was inside the core, and the other with the liquid outside the core. Tests with the liquid inside the core were run to cover the saturation range encountered in both the drainage (gas drive) and imbibition (liquid flood) flow systems. It is pointed out that the same core was used, but the tests were conducted at different times with the recording mechanism balanced at a different position. Therefore, the absolute values of relative X-ray intensity at any saturation are not the same in each test. In the second type of test the same core was used, but this time its pore space cmtained only gas, and various thicknesses of oil contained in plastic cells were placed in front of the dry core. As before. the relative X-ray ah- sorption was measured and compared to the quantity of oil in front of the core. The arrangement of the fluids with respect to the path of X-rays in these two types of tests represent fluid distributions of a wider difference than can be expected between that established in a core just due to imbibition and drainage saturation flow histories. Thus any deviation from a straight line relationship of the log of the relative X-ray intensity us saturation calibration should be readily apparent. Results of the laboratory tests are given in Fig. 1. A schematic diagram showing the position of the fluids with respect to the path of the X-ray beam is given for the two cases investigated. In the case where the oil existed outside the core (Case B), the log of the X-ray intensity (log, I/I,) is related directly to the cell thickness (amount of oil in X-ray beam path). This correlation is in full agreement with X-ray theory. In the case where the oil or water existed inside the core (Case A) which covers both drainage and imbibition types of flow processes, again the relationship between absorption and saturation (amount of oil in X-ray beam path

Jan 1, 1952

By Claudia Gasparrini

Silver occurs in nature in major, minor and variable amounts in a very large variety of minerals and in several mineral species in the same ore. Because these minerals may respond differently to the same flotation or leaching agents, detailed studies to establish the correct silver mineralogy become essential for optimum recoveries in those situations where the silver is treated as a primary product. On the other hand, fine grain sizes, which often affect gold recoveries, are not generally as critical in silver metallurgy, due to the lower market price which allows for more of the element to remain In the tailings before incurring in economical losses.

Jan 1, 1984

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By C. E. Sims, G. A. Lillieqvist

The following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admittedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold arc outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided. Relation between Ductility and Nonmetallic Inclusions In September, 1928, an acid electric furnace was put into operation at the Indiana Harbor plant of the American Steel Foundries. Following the usual practice, aluminum additions were made in order to obtain sound castings. Immediately the problem of low ductility arose. Previous to that time, only open-hearth steel was produced, and, aluminum being used rarely in that steel, there had been practically no trouble with low ductility in the lower carbon range.

Jan 1, 1932

A shrinkage stope is an overhand stope in which the broken ore accumulates until the stope is completed to, or near, the level above. As broken ore generally occupies at least 60 per cent. more space than ore in place, about a third of this must be drawn out as the stope advances to leave a working space under the back. The ore remaining supports the miners and gives temporary support to walls, and is all withdrawn when the stope is finished. The shrinkage-stope method is applicable to steep-dipping deposits of strong ore with strong walls. It may be applied to narrow or wide veins, and is simple and cheap. Five examples, which include important and varied types of deposits, are given: namely, Kennecott, Homestake, Jarbidge district, Mogollon district, and Cripple Creek district.

Jan 1, 1925

INTO their great Pacific Northwest counting house went the members of the Industrial Minerals Division recently, to count their blessings amidst the scenic grandeur and mineral wealth of the State of Washington. From their vantage point in Seattle, those who attended the IMD's fourth Pacific Northwest meeting turned their sights to the South and Southeast, scanned Montana, Idaho, Oregon and Utah, and predicted a very healthy economic future for their region. The praises of Idaho's booming phosphate industry were sung by Earl W. Murphy, secretary of that State's Chamber of Commerce. He said the establishment of Fort Hall, on the banks of the Snake River near Pocatello, first turned the eyes of the world toward what is now the center of the greatest known deposits of phosphate rock-the section adjacent to the common corners of Idaho, Wyoming and Utah. With the founding of Fort Hall, Mr. Murphy said, historians will also rank the construction of the first electric furnaces for the production of elemental phosphorous as equally significant in the commercial history of the West. Those furnaces were installed only last year by the Westvaco Chemical Div. of the Food Machinery & Chemical Corp. at Pocatello, at a cost of $8 million.

Jan 7, 1950

NEW MEMBERS The following list comprises the names of those persons Who became members during the period July 10, 1918, to Aug. 10, 1918. ARCHER, EUGENE G., assayer and Chem., Granby Cons. Min. Smelt. & Power Co.,Anyox, B. C., Canada. BAKER, ROBERT C Mech. Engr. and Draftsman, Moctezuma Copper Co., Nacozari, Son., Mexico. BARNES, EDWARD A Supt., Fort Wayne Works, General Electric Co., Fort Wayne, Ind. BARNHART, EDWIN Engr. of Tests, Bethlehem Steel Co., Sparrow's Point, Md. BENSLEY, MAURICE D Pres. and Mgr., Frontier Brass Foundry, Inc., Niagara Falls, N. Y. BRADLEY, JOHN C Met., The American Brass Co., Waterbury, Conn. BRAGG, C. T Works Mgr., Michigan Smelt. & Refin. Co., Detroit, Mich. BRYMER, GEORGE W Min. Engr., 922 Union National Bank Bldg., Scranton, Pa. CHIVVIS, NORMAN Met. Engr., More-Jones Brass & Metal Co., 3144 North Broadway, St. Louis, Mo. CRAWFORD, R. D Prof. of Mineralogy & Petrology, Univ. of Colorado, Boulder, Colo.

Jan 9, 1918

NEW MEMBERS The following list comprises the names of those persons who became .members during the period of Jan. 10, 1918, to Feb. 10, 1918. ANTISELL, TONER, Min. Engr.; Supt., Great Falls Mine of Maryland, Chevy Chase, R: F. D. No. 4, Washington, D. C. BAKER, RAYMOND FRANK, Geol:, The Texas Co., Producing Dept., Box 362, Tulsa, Okla. BERTON, ADRIEN, Chief Engr., Corocoro United Copper Mines, Ltd., Corocoro, Bolivia. Buck, WILMER EARLE, Met., Curtis & Co. Mfg. Co., Hamberger & Kienlein Aves., St. Louis, Mo. BUELL, WILLIAM H., Asst. Director, Experimental Station, E. I. duPont de Nemours & Co., Wilmington, Del. CARDENAS, FEDERICO F., Mgr., Cia. Minera Nazareno y Alicante, S. A., Allende, No. 112, Saltillo, Coah., Mexico. CHEVALIER, JEROME A., Pet. Geol., The Carter Oil Co.; Exchange National Bank Bldg., Tulsa, Okla. CLEAVES, DANIEL LUNT Supt., St. Joseph Lead Co., Herculaneum, Mo. CLOTHIER, GEORGE A., Resident Min. Engr., Province of British Columbia,

Jan 3, 1918

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-clays, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 4, 1913

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By J. D. Hunt, R. J. McDonald

It is proposed that extensive fluid motion occurs between the dendrites of a Partially solid casting and it is suggested the A segregates in steel castings are a direct result of this motion. The fluid flow arises because of density differences between liquid ahead of the dendrites and the interdendritic liquid. Experiments are described on a model system investigating this fluid motion. The importance of interdendritic fluid flow is discussed with reference to longitudinal segregation. SERIOUS macro segregation is often found in large killed steel ingots. Among the most common segregates are those known as A and V, Fig. 1. The A segregates are arranged over the surface of cones, the wide parts being at the base of the ingot. The A segregates are pencil like in shape and extend from the columnar into the equiaxed region. The V segregates are distributed over inverted cones but have a less well defined shape. They occur at the center of the ingot. Because of the commercial importance of macro inhomogenities these segregates have attracted wide-scale attention. The segregates contain alloying elements and impurities which depress the freezing temperature and are thus the last liquid to freeze. A number of explanations have been proposed to explain their presence. It has been suggested1'' that the segregates are the result of the equiaxed zone growing towards the columnar region together with the interaction of convection within the bulk liquid. It has also been proposed that the segregates are the result of nucleation and rapid growth ahead of the dendritic front.3 Neither of these explanations is completely satisfactory because A segregates are pencil shaped and are not found as continuous cones. In this paper an alternative mechanism is proposed, and experiments are described on a model system to determine whether the mechanism occurs in practice. It is thought that A and V segregates are not peculiar to steels but should occur in many other large castings. Fluid motion within the bulk liquid region of a casting has been extensively discussed. Little attention has been paid to fluid motion within the partially solid regions. The work415 that has been done has been mainly concerned with the fluid motion which results from the volume contraction on freezing. The volume contraction is used to explain various types of macro segregation. The present authors suggest that in many cases the fluid flow resulting from volume contraction will be small compared with that due to other causes. When the columnar region is growing, the liquid still remaining between the dendrites has a much lower temperature near the ingot walls than at the dendrite tips. The composition of the liquid in contact with solid will vary with temperature. The density of the liquid will thus vary both because of changes in temperature and composition. The layers of different density liquid will give rise to a slow but steady liquid flow through the interdendritic regions. If there is no density change with composition, the temperature gradient within the dendritic region should give rise to a downward flow between the dendrites, shown schematically in Fig. 2. When the liquid density changes appreciably with alloy concentration this motion could either be en-

Jan 1, 1970

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Eric Jette

THE alloys of gold and iron were investigated in 1907 by Isaac and Tammann,1 who determined the thermal diagram for the entire system by thermal analysis and microscopic examination. They also reviewed the previous literature. Since that time the present authors have been able to find only two additional references. Guertler and Schulze2 examined the electrical resistance of iron alloys containing up to 40 per cent by weight of gold between 0° and 200° C.; the alloys were in the form of wires. The main result of this work was to confirm the solid solubility limit found by Isaac and Tammann; namely, about 20 per cent Au. More recently, Shih3 has examined the magnetic properties of gold alloys containing up to 10 weight per cent iron and particularly the range below 5 per cent. The alloys in the lower range were found to be paramagnetic; the 10 per cent alloy was ferromagnetic. The present investigation was undertaken to determine the solid solubility limits at various temperatures, particularly below the a-y transformation point of iron, since these solubilities are of some impor-tance in connection with the working of the alloys in the manufacture of certain "grey" and "blue" golds.

Jan 1, 1934

By W. T. Allan

RAW bituminous coal has been in general use as a blast-furnace fuel in Scotland for the last century, and although its use has now been largely abandoned and it has been replaced by coke in the majority of the few furnaces which are at, present in blast in this country, coal-smelted pig iron is not yet a thing of the past; it is still being produced and mar-keted in competition with the more cheaply smelted product of the coke-fired furnace. Various factors have influenced this change in practice; the once plentiful deposits of coal of a suitable nature for the blast furnace are now not so easily obtainable; native blackband and clayband ironstones which are easily smelted in the coal-fired blast furnace, although still far from being exhausted, are not available except at a. cost that is somewhat higher than that of imported ores, making them unattractive to the ironmaster that is compelled by circumstances to smelt his iron at the lowest possible cost. Within the last 15 years overproduction of synthetic nitrogen has led to progressive reductions in the price of sulphate of ammonia, the recovery of which together with the other by-products before that time materially assisted in reducing the working costs of the coal-fired furnace. Now the sale of the by-products recovered yields a diminished profit. When the cost of the product is the only consideration the small, slow-smelting, coal-fired blast furnace cannot compare with its large, modern, coke-fired competitor. Other `considerations do not by any means all support the same side of the argument. In the smelting of pig iron to be used in the manufacture of steel where the quality of the final product depends so largely upon the control of the conversion process and so much less upon the physical quality of the pig iron used, the physical properties of the pig iron do not exert any appreciable influence upon the quality of the steel produced, therefore the methods employed in the smelting of the pig iron matter but little so long as the requisite chemical composi-tion is reached. On the other hand, in ironfounding where the simple melting of the pig iron, which is the only treatment it receives before being cast into its final form, does little or nothing to modify its original charac-

Jan 1, 1937

By Charles R. Keyes

I. INTRODUCTION. FOR a period of several years, and in a large number of cases, the Metallurgical Laboratories of the New Mexico School of Mines were employed in umpire work. During this time many important local problems were solved. Against the results of careful chemical analyses of ores, assay-returns were often checked. In many cases the assay-methods of mine and custom-smelter were compared, and both often found faulty for the ore concerned. A wide range of ores was covered. Many of the chemical analyses and assays were made by Dr. F. C. Lincoln, Professor of Metallurgy, now of the Montana State School of Mines. A varied series of instructive assays was prepared by Prof. R. B. Brinsmade, now of the West Virginia State University. Single assays and given series of tests were undertaken by H. T. Goodjohn, now chief chemist to the Cia. Metalurgica de Torreon, Coahuila, Mexico; by H. J. Hubbard, now superintendent of the Butters Divisadero Mines, Jocoro,. San Salvador, C. A.; by E. D. Morton, now superintendent of the Arizona & Nevada Copper Mining Co., at Lunning, Nev. ; and by A. W. Edelen, now superintendent of the Angangueo Unit of the American Smelting & Refining Co., in Michoacan, Mexico. A critical comparison of assay-methods that were found to be followed in the case of certain gouge-ores mined in the Mimbres range in New Mexico, and about which there had been much controversy, was made by D. F. Riddell, then Acting Professor of Assaying, and now superintendent of the Providentia Mines Co. of Parral, in Chihuahua, Mexico. To him is due the credit of much that is contained in the following notes, which be has generously permitted -to be used in advance of the publication of the complete results.

Jul 1, 1911

By Ira N. Holli

A meeting of Engineering Council was held on Thursday, Jan. 22, 1918, at the Engineering Societies Building, New York. Present: Chairman Ira N. Hollis (A. S. M. E.); Dr. Charles Warren Hunt, Alex. C. Humphreys and F. H. Newell (A. S. C. E.); B. B. Lawrence and .J. Parke Charming (A. I. M. E.); Charles Whiting Baker, D. S. Jacobus, and George, J. Foran (A. S. M. E.) ; H. W. Buck, E. W. Rice, Jr., N. A. Carle, C. E. Skinner and Comfort A. Adams (A. I. E. E.) ; Clemens Herschel and Calvert Townley (United Engineering Society); also, by invitation, D. W. Brunton, Chairman, War Committee of Technical Societies of Engineering Council. Of the several actions taken at this meeting, the following are selected as being of most general interest. Chairman-Baker-presented a resolution on the conduct of the war, to which objections were made. It was referred to a special-committee; Charles Whiting Baker, Charles Warren Hunt, and Calvert Townley, for re-drafting and presentation later in the meeting. The revised resolution submitted by this committee led to further discussion and as no agreement could he reached, the matter was laid on the table.

Jan 3, 1918