Search Documents

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modelling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. Three-dimensional numerical direct shear tests were conducted on the coupled FD-DE model of the combined rock-cemented rockfill (R-CRF) specimens with the frictional-bonded interface. With the microstructural parameters determined, the macro-mechanical properties of the interface of the coupled model were calibrated to well fit with the theoretical values of the combined specimen under the direct shear condition assumed according to the Mohr–Coulomb strength criterion. Evident elastoplastic shear behaviour was observed on the interfaces, and excellent agreement was attained between the shapes of the theoretical and simulated shear stress-displacement curves of the coupled models at different servo-controlled normal stresses. Particulate-scale force chains inside the DE model of the CRF specimen were highly consistent with the force contour on the FD model of the rock specimen, demonstrating the shear stress evolution of the coupled model at different shear displacements. Parametric studies verified the effects of the deformation properties of the interface parallel bonds on the shape of shear stress-displacement curves of the coupled models. The test results validated the feasibility and rationality of the coupled FD-DE method for modelling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modelling experience for investigating the shear behaviour at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

Nov 2, 2021

By Andrzej M. Wala

A knowledge of the friction factor (K-factor) is necessary in planning and designing mine ventilation systems for least cost and highest effectiveness. The friction factor used must be accurate and reliable for correct estimation of airway resistances. At present, the friction factors are determined by using tables of published values. These values were established principally for metal-mine openings having small effective areas. This presents a problem to the ventilation design engineer whose responsibilities center around the design of effective ventilation systems for large room-and- pillar mechanized underground coal mines. Friction factors selected from these tables could be excessively conservative for large scale room-and- pillar operations. With only limited data on the K-factor (which are considerably site dependent) for Kentucky's coal mines and for all the above mentioned reasons, it was concluded that there is a need for field investigations to determine these values in-situ for existing mining conditions in Kentucky. The author describe the study carried out in ten coal mines located in eastern and western Kentucky and present the results of the investigation in both tabular and graphical form.

Jan 1, 1991

Jan 1, 1967

By Claude Cunningham

The primary reason for blasting is to fragment rock. In production blasting, the fragment sizes produced are known to exercise an overwhelming influence over working costs: handling costs and tonnage throughput are directly affected by secondary breaking, loading and crushing, all functions of fragmentation. In addition, particular size fractions are frequently of intense interest in terms of market or process requirements.

Jan 1, 1995

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By Michael G. Pojar, Peter G. Chamberlain

Solution mining, primarily by heap leaching, has emerged as an important method for mining gold and silver in the United States. Heap leaching offers many economic and environmental advantages over conventional production techniques, in particular for lean ores and old mine waste rock. In order to more effectively pursue research on heap, dump, and in situ solution mining of gold and silver, the Federal Bureau of Mines conducted an extensive survey of leaching practices and problems. This presentation summarizes trends and statistics. Leaching is projected to provide 20 pct of primary mine produced gold and 10 pct of primary silver by the end of 1982. Current leaching practices in the United States are reviewed; operational problems and research programs to alleviate those problems are discussed.

Jan 1, 1981

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By Reno H. Sales

Our colleagues cannot in the future earn reputations and medals for achievements in milling and smelting ore and for successful management of mining companies, if some one doesn't keep finding and mining the ore to mill and smelt and to provide the basis for the good management. Good ore seems sometimes to be quite helpful to good management, and good ore is not as easy to find as it used to be. And there are still more reasons, why—when this honor had been decided upon and named for Mr. Daniel C. Jackling—it should be initially conferred on Reno H. Sales. . The terms of reference of the award are that it should be conferred upon an individual working in the fields of mining, geology, geophysics, who has made an outstanding contribution to the progress of technology in one or more of those fields. And in this initial year (the earlier years are the easiest) just that was done. I think I could get away with it amongst the old-timers of my generation if I say that this time they made the award to the individual, who made the outstanding contribution. But, as Al Smith used to say, "Let's look at the record." Really, the record is mixed up a little with extra-lateral litigation—the old-time "apex cases" under Section 2322 of the Revised Statutes. Reno Sales doesn't like such litigation, but there is little question that the urgency, generated by conflicting claims of intra-limital and extra-lateral rights, and consequent necessity for committing to records and maps the complications of Butte structure, did advance—and by several years—the first continuous, accurate, systematic, and scientific portrayal of the geological and mineralogical details of what is, after all, the most important and the most complicated copper district—at least in North America. Prior to Sales' time, some of the most eminent of geologists often waived details. One geologist took the judge to the window to show him the Rarus fault going through a notch in the Continental Divide. The entertaining testimony in the Bluebird litigation was as perfect in literary style as it was innocent of the criteria by which faulting and lack of continuity of vein structure are now recognized. At any rate, this need for an accurate record of structure was in the background—to whatever extent it was, or was not, the etiological agent—for formation of the Geological Department of the Amalgamated Copper Co. in and about the year 1900. Charles W. Goodale was at that time the head of the Boston & Montana, and John D. Ryan succeeded William Scallon as the president of Anaconda Copper Mining Co. in 1905. Horace V. Winchell, for years a specialist in extra-lateral litigation, was perhaps the man who at that date had the vision, the persuasive weight with the management, and the willingness to defend the idea of large current expenditures (as then viewed) for a complete and sys-

Jan 1, 1955

By Jun Deng

The aim of this paper is to study the scientificity and reliability of three coal gas indices used to predict coal fire disasters, namely Graham?s ratio, CO/CO2 ratio, Litton ratio and their different characteristics and service conditions. Data from a programmed temperature experiment were applied to check their veracity and accuracy. Each index performed well in detecting the level of a fire. We conclude that it is better to redefine the definition through experimentation before applying a given index. Integrated analysis of the results can provide reliable reference data for predicting spontaneous combustion of coal.

Aug 1, 2013

By R. J. Baumgartner

Sustainability issues are from rising interest and importance for the mineral industry worldwide. In order to bring them into management processes and to improve decision processes, economic, ecological and social aspects of products, services or technologies have to be assessed. In this paper, the concept of integrated sustainability assessment is presented. Each aspect is assessed with quantitative or qualitative methods. The results of these ecological, social and economic sub-assessments are integrated by the means of Fuzzy Logic in order to regard preferences of decision maker and circumstances of decision situation. An example demonstrates the application of this new instrument.

Jan 1, 2005

By Michael Schmitz, Eugene Ahrenholtz, William A. Heitbrink, Jeanne A. Zimmer, Andrew B. Cecala, Ernest S. Moyer, Earle H. Andrews, Chris C. Coppock, John A. Organiscak

Many different types of surface mining equipment use enclosed cabs to protect equipment operators from health and safety hazards. The overburden removal and mining process can be extremely dusty and can cause excessive dust exposure. To study this issue, a cooperative research effort was established between the National Institute for Occupational Safety and Health, U.S. Silica Co., Clean Air Filter Co., and Red Dot Corp. in an effort to lower respirable dust levels in an enclosed cab on an older surface drill at a silica sand operation. Throughout this research effort, a number of modifications were incorporated into the drill's filtration and pressurization system, as well as in other areas, to improve its design and performance. An average cab efficiency of 93.4% was determined with gravimetric sampling instruments when comparing the outside with the inside cab dust levels on the final design. Although this study considered just one operation, the goal was to identify cost-effective improvements that could be implemented on all types of enclosed cabs to lower respirable dust concentrations. Two critical components for an effective enclosed cab system are having a properly designed, installed, and maintained filtration and pressurization system, along with a method for maintaining structural cab integrity, which allows the cab to be positively pressurized. Another important component is maintaining cab cleanliness. Although this research was originally directed toward the mining industry, it is also applicable to agricultural or construction equipment.

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By Pat Wilmoth, Joseph P. Gildner, Dan Nowak, Shane Yanagisawa, Don Z. Painter, Gordon F. Revey

Frontier/Traylor is presently completing construction of twin tunnels for the Tri-County Metropolitan Transit District of Oregon’s (Tri-Met) westside lightrail system. The tunnels are each 4,550 m (14,935 ft) in length and 6.48 m (21.29 ft) in diameter. The 1/3 of each tunnel was driven from the west portal using drill and blast methods and the remaining 2/3 was driven from the east portal using a TBM. The paper describes: The difficulties encountered by the TBM mining the weathered Columbia River Basalts. The execution of drill and blast work despite challenging ground conditions, stringent noise and vibrations specifications, and public relations problems. The excavation and lining of the Washington Park Station 79 m (260 ft) below the park zoo.

Jan 1, 1997

By Robert J. Kuhne

The Iron Ore Company of Canada has successfully employed advanced process control (APC) to optimize the operation of their induration machines. A significant increase in machine throughput and a reduction in fired pellet quality giveaway were observed following the APC implementation on all six machines. This paper discusses the opportunity for process control optimization in induration, reviews the property estimation and multivariable control technologies, and describes how the IOCC control strategy captured this opportunity. APC performance data is presented. The dependence of APC performance on control room operator acceptance, process equipment and instrumentation is highlighted.

May 1, 2007