Search Documents

By Xiangwen Wang

Electrochemical measurements associated with the electrowinning of lead metal from concentrated brine (NaCI) - lead chloride (PbCI,) electrolytes at temperatures in the range 328 to 353°K (55 - 80°C) were conducted. The electrodeposition of lead metal onto a lead rotating-disk electrode may be described by the electrodic reaction: {PbCl 4 2 + 2e- = Pb° + 4Cl-} The deposition-overpotential requirements are low (approximately 41mV per decade of current density - Am+), with a corresponding high exchange current (approximately 0.018 A.cm2). The diffusion coefficient of the electroactive PbC142- species in a 3.5 NaCl electrolyte at 353°K was insensitive to the total PbCI, concentration (0.01 to 0.1M), and its value was found to be (1.21*0.1)~10-5 cm2Is with a temperature-sensitivity coefficient (E,/R) of approximately 1.98x103K-1 (328OK(T<353OK).

Jan 1, 1993

By Nadia H. Rafat, Iman S. El-Mahallawi, Hussein Badr, N. Khattab, Ahmed A. Abdel-Rehim

The basic part of solar water heaters is the collector and the main functional part of the collector is the absorber layer. In this work, a commercial locally available black painting (PACEN code 10382 colour 890), used for swimming pools solar heating, was modified by adding nano-graphite dispersion. The effect of nano-graphite particles percentage on the spectral absorbance of the material was examined on samples containing two values of 1.5 and 2.5% nano-graphite particles by weight. Fourier transform spectroscopy (FTIR) analysis was also used to identify the functional groups in the developed material. A simple experimental setup was designed to evaluate the performance of the developed nanodispersed selective coating polymeric based material, by measuring the increase in temperature of circulating water. It was shown that adding 1.5–2.5% nano-graphite particles to a polymer based black coating causes an increase in the optical absorptance, and an increase in the circulating water temperature.

Mar 1, 2018

By C. P. Snyman

Three independent methods of coal classification can be distinguished, namely on the basis of grade, type and rank. The latter two can be determined accurately and unambiguously only by means of microscopical techniques. These three independent variables affect all the coal properties and therefore also the technological behaviour of a particular coal. The influence of the inorganic constituents of coal on the fusibility of the ash and on the length of the slag, and also on fouling and slagging, is discussed. The fractionation of the ash-forming constituents during combustion and gasification of pulverised coal shows that fouling and slagging are not related directly to the fusibility and composition of ash of the coal as a whole. The results of combustion experiments using a drop furnace technique indicate that the ignition temperatures of the light volatiles in the coal, and of the formed char, as well as the burn-out time of the char are more dependent on the rank than on the type or grade of the original coal. High-ash coals, however, apparently ignite at lower temperatures and are more reactive than low-ash coals of similar type and rank. The surface properties of coal, which are important in froth flotation and oil agglomeration, correlate well with the inherent moisture content (and by inference with the heat of wetting and the calorific value) and therefore with the type and rank of the coal. In coal exploration, variations of rank offer the possibility of predicting the presence of an intrusion near the seam, thus contributing to more effective exploration and mine planning.

Jan 1, 1991

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don&apos;t assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don&apos;t have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By C. Dupuis

Thiourea is a promising reagent for gold extraction especially from refractory ores that cannot be treated by traditional cyanidation route. In this study recovery of gold from thiourea leaching solutions was investigated by direct electrowinning. The electrolysis cell consisted of a carbon flow-through cathode and a lead anode. The anodic and cathodic compartments were separated by a membrane. Galvanostatic mode was chosen for operation of the cell. Factors affecting recovery efficiency such as cathode thickness, linear flowrate, current intensity, thiourea and gold concentrations were investigated. The influence of some species in solution on efficiency and selectivity of recovery was investigated. Gold recovery reached 99% but current efficiency was lower than 10%. The complex formed with ferric ion and formamidine disulfide are reduced before gold-thiourea complex. Thiourea consumption occurred during leaching mainly by oxidation and reaction with dissolved copper.

Jan 1, 1989

By Yungang Li, Hui Li, Ramana G. Reddy, Jinglong Liang

High solid corrosion protective coatings were prepared by the dust of the converter with an average particle size of 59.33 μm. The effect of different amount of benzyl alcohol diluent on the performance of high solid anti-corrosion coatings was studied. With the increase of the amount of diluent, the viscosity of high solid anti-corrosion coatings reducing, the film apparent bubble content decreasing, and film resistant to salt water corrosion ability decreased, while acid corrosion capacity enhancement. When the dosage of diluents is 15%, the coating film is more resistant to acid corrosion.

Mar 1, 2017

By J. Grogan

Leaching of galvanized steel coatings allows the steel substrate to be used as a zinc-free scrap source to steel and iron furnaces. In this study the behaviors of sulfuric acid leaching solutions are investigated. The ranked significance of the variables are shown to be acid concentration > temperature > zinc concentration. Examination of the leaching mechanism finds the rate-limiting step to be the cathodic hydrogen reduction reaction. This rate is not only influenced by acid concentration, but also by the hydrogen reduction exchange current density. Dezincing leaching rates are improved by taking advantage of the higher exchange current density of the iron substrate versus the zinc coating. This is accomplished in practice by increasing the exposed interfacial zinc:iron surface area through shredding. Also, a leach control mechanism is proposed through online monitoring of the zinc-iron couple mixed potential.

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By Pedro Henrique L. M. Lopes, Édio Pereira Lima Jr., Fernanda Santos da Luz, Fábio de Oliveira Braga, Sergio Neves Monteiro

Several works have been dedicated to study the ballistic response of multilayered armor systems (MAS), including those using natural fiber composites as second layer. These composites disclosed good ballistic performance, having economic and environmental advantages. In the present work, the objective was to investigate the effect of areal densities of each MAS layer, in the overall performance of a MAS with an alumina ceramic front, a curaua fabric reinforced composite filling, and an aluminum alloy backing the target. Ballistic “backface signature” tests were conducted, varying the areal densities of the MAS layers according to a Box-Behnken design. The results showed a similar influence of the ceramic and aluminum layers in the MAS “backface signatures”, although deformation and failure mechanisms were significantly different. The composite also showed significant participation in the overall MAS performance. Since the composite is cheaper and lighter, a balance minimizing the other layers would be advantageous.

Mar 1, 2018

By Yijia Dong, Mingjun Rao, Pengxu Cao, Jun Luo, Guanghui Li, Zhiwei Peng

Coal fly ash (CFA), as a by-product generated from coal fired power stations, is widely used for autoclaved concrete block production. It has been found that the generation of tobermorite is great benefit to the block strength during autoclaving. In this study, the tobermorite fibers synthesized from CFA and lime via the hydrothermal process are used as the revulsive to promote the mechanic strength of the concrete blocks. The results show that tobermorite fibers with 0.01–0.5 lm in diameter and 1–3 lm in length are obtained at 200 °C for 0.2 h. As the addition of prepared tobermorite fibers increases from 0 wt% to 2.0 wt%, the compression strength of concrete block increases from 24.6 to 40.5 MPa, and the compression strength of aerated concrete block produced under the optimized conditions can reach above 7.5 MPa.

Mar 1, 2018

By V. Reiter, K. Reinharter, C. Wenzl, D. Gregurek, A. Spanring

The refractory linings in lead furnaces are exposed to several stresses rather complex in their interaction. In the present study the magnesia-chromite brick out of a lead recycling furnace suffered from a high chemical attack by the process slag. The high CaO, BaO and sulfur bearing silicate slag, as well as a high NaO2 supply from soda resulted both in a deep-reaching infiltration of the brick microstructure and a severe corrosion of the brick components. Both the sintered magnesia and chromite were attacked chemically. The FactSage calculations showed the formation of high amounts of liquid phase in the infiltrated microstructure. Further phenomena affecting the refractory performance such as iron oxide attack, redox effects, and boron attack are also discussed in the paper. The obtained information and insights serve as a basis for improving refractory materials (i.e., choice of refractories for individual process and new developments) and consequently furnace operations.

Mar 1, 2017

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By Zhanjun Wang, Mei Zhang, Zuotai Zhang, Min Guo

In this study, the viscous flow and crystallization behavior of CaO–SiO2–MgO–Al2O3–FetO–P2O5–TiO2 steelmaking slags have been investigated over a wide range of temperatures. The results indicated that the viscosity of the slags slightly decreased with increasing TiO2 content. The constructed non-isothermal continuous cooling transformation (CCT) diagrams revealed that the addition of TiO2 lowered the crystallization temperatures. This can mainly be ascribed that the addition of TiO2 promotes the formation of [TiO6]-octahedra units, thereby MgFe2O4–Mg2TiO4 solid solution is formed. Moreover, the decreasing viscosity has a significant effect on the diffusion of ion units, such as Ca2+ and [TiO4]-tetrahedra, from bulk melts to crystal-melt interface. The crystallization of CaTiO3 and CaSiTiO5 was therefore accelerated, which can improve the phosphorus content in P-enriched phase.

Mar 1, 2017

By Eulogio Velasco, Jose Nino, Marcos Cardoso

"Recycling of aluminum scrap for production of secondary alloys used for automotive applications is increasing continuously. Automotive alloys require a strict control to remove alloy impurities, inclusions and excess of magnesium. The advantage of aluminum is its recyclability with large energy and emission savings with minimal loss in material properties. The aim of this work is to study the magnesium removal from recycled aluminum by chlorine injection in a reverberatory furnace, and removal by an oxidation process at high temperature in an industrial rotary furnace.The magnesium removal by gas injection is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors. In the rotary rapid oxidation of aluminum and magnesium elements at high temperature is characterized by the formation of surface films composed of magnesium oxide. Additionally this work reviews the benefits of an efficient demagging process.IntroductionThe advantages of using light alloys for automotive applications include fuel economy improvement, greenhouse gas reductions and polluting emissions. These characteristics makes the aluminum alloys an attractive option for automotive components such as powertrain products and other critical parts like cylinder heads and blocks. [1]Aluminum alloys coming from recycled automotive components, used beverage cans (UBC) and wrought alloys have positive effects in the energy savings and current environmental trends. Producing a scrap recycled aluminum ingot consumes approximately 5% of the energy required to produce a primary aluminum ingot from bauxite ore. [2]"

Jan 1, 2011

By James Cornwell, John A. Elton

"Thermionic induced reactions and radiation resonance catalysis of aluminum and aluminum oxide materials exposed to microwaves and triboemissions will be described and explained from both a fundamental and practical level. Magnetron operation at distinct operating conditions that generates both plasmon and triboemissive radiation will be explained and the resulting tribochemical and radiation resonance catalytic reactions between aluminum, aluminum oxide, water and graphite will be delineated. The generation of hydrogen from these materials using triboemissive radiation and microwaves will be described, and the application of this methodology for hydrogen based technologies will be discussed.IntroductionProtective Systems Directed Energy RadiationProtective Systems, Inc, has developed a new radiation device called the EMR (Electromagnetic Resonator) that has unique characteristics that separates it from traditional microwave and rf radiation devices. The radiation from the EMR device is generated using a modified electronresonance magnetron with proprietary filters and operating characteristics.Electronic Device Shutoff. When electronic devices such as cell phones, computers, and other IC based electronics are placed within the EMR radiation, these devices become non-functional as long as the EMR beam is active. Upon removal of the EMR radiation the devices either become operational again or become operational after a cold start. The devices are not damaged by the irradiation.Faraday Cage Interaction Effect. When any of the above electronic devices are placed in a Faraday cage and activated within the Faraday cage without EMR radiation, they operate normally. However, these devices will still be rendered inoperative when an EMR beam generated outside the Faraday cage is directed at the electronic."

Jan 1, 2010

By Zhucheng Huang, Zhikai Liang, Lingyun Yi, Tao Jiang

"In this study, reduction of iron ore pellets was carried out at 800-950°C by simulating the atmosphere of typical coal gasification gas. The effects of temperature, gas composition and reduction degree on swelling were investigated respectively. Reduction degree was obtained according to the weight loss records. And volume changes of pellets during reduction were evaluated by infrared photography. Results showed that the pellet swelling increased with temperature and decreased slightly with hydrogen content in the reducing gas. The swelling peaked when reduction degree reached about 40% and then decreased to be stable finally. The microstructures of pellets during reduction were examined by reflected light microscope and relatively rational explanations were proposed for their swelling behaviors.PrefaceDirect reduction iron is an important and indispensable raw material for high-purified and high-quality steel in the electric furnace smelting. Gas-based shaft furnace direct reduction process has very strong competitative ability; however, this technique requires natural gas as reducing agent, so its development has been restricted by gas source and area. Compared with gas-based reduction method, coal based reduction method has the disadvantages of higher production cost and lower productivity. In China, coal resources are abundant and coal gasification technology is mature, and the development of coal gasification shaft furnace direct reduction process is promising. [1] The gasification methods of fixed bed method (Lurgi method), fluidized bed method (Undok method), airflow bed method (Texaco coal water slurry method and Shell dry powder coal method) have been put into use successfully. These syngas generated by different methods can meet the actual production requirement of shaft furnace. However, the compositions of the effective reduction gas in the syngas are quite different. The ratios of hydrogen and carbon monoxide (H2/CO) of Undok or Shell coal gas, Texaco coal gas and Lurgi coal gas are 0.4, 0.6~ 1.0 and 1.6~2.3, respectively. [2] In the coal gas direct reduction process, the swelling behavior of iron ore pellets is various due to the differences of the gas composition, reduction temperature and reduction degree, and it seriously affects the normal operation ofDRI production. [3-9] Therefore, the research on the swelling behavior and its mechanism of iron ore pellets in direct reduction were carried out in this paper."

Jan 1, 2013

By C. M. Wai

Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ chelation-supercritical fluid extraction technique offers, several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, ß-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.

Jan 1, 1996

By Xudong Liu, Ganghua Fu, Yufeng Guo, Wei Chen, Yujia Tan, Tao Jiang

Willemite is usually found in high-silicon oxide zinc ore and zinc metallurgical secondary resources but without effective extraction method yet. In this study, zinc was extracted from willemite by sodium salt roasting and ammonia-leaching process based on the idea of zinc phase reconstruction. The effects of Na2CO3 dosage, roasting temperature and roasting time on phase transformation and zinc leaching rate were studied, respectively. The results show that Zn2SiO4 was transformed into ZnO or Na2ZnSiO4 during roasting process. After roasting at 800 °C for 2.5 h at ratio of n(Na2CO3)/n(Zn2SiO4) = 2.5:1, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.62% in NH4Cl–NH3–H2O leaching system, which increased by 91.57% compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl–NH3–H2O system.

Mar 1, 2017

By A. Yudiarto, M. Z. Mubarok

At the present paper, synthesis of magnesia from ferronickel smelting slag is discussed. The first stage was extracting magnesium from the slag by leaching in HCl solution. Magnesium extraction of 97% was obtained from the slag leaching with HCl 8 molar, solid:liquid ratio 1:40 (g/ml) and temperature 80 °C after 24 h. Solution purification was performed by adjusting solution’s pH at 95 °C with addition of MgO powder. At pH range range of 3–4, co-dissolved iron was removed as akagenite (b-FeOOH) precipitate. Dissolved nickel precipitation was detected at pH range of 4–6, while dissolved Mg and Al started to precipitate in the forms of pyroaurite (Mg6Fe2CO3(OH)16∙4H2O) and hydrotalcite (Mg6Al2CO3(OH)16∙4H2O) at pH range of 8–9. High purity of brucite (Mg(OH)2) was obtained by Mg precipitation at pH range of 11–12, under stirring speed of 300 rpm and stirring time of 4 h. Calcination of brucite at temperature of 1000 °C completely converted brucite to periclase (MgO) powder after 240 min.

Mar 1, 2017

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986