Search Documents

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By J. Hartikainen

19 papers were allocated to this session by the paper classification committee, 8 related to bored piles, 5 to continuous flight auger piles (CFA piles), 3 to slurry trenches, 2 to both bored piles and slurry trenches, one of them also dealing with root piles. There were no papers dealing with root piles only, as root filling is a different technique. One paper concerns sheet piling (Table 1). Table 1. Papers for session 1: Recent Technological Developments in Deep Foundations with Soil Excavation. [ ] Table 2. Classification of pile type in Belgium - van Impe W.F. /10/. [ ] Trends in piling Trends in piling in Central Europe were studied by van Impe for his brilliant lecture to the Finnish Civil Engineering Society. He claimed that bored piling is on the decrease and CFA pilling on the increase (Table 2). Thus the numbers of papers presented here do not conform to recent developments or trends. The papers submitted arc of course influenced largely by the fact, observable in Table 3, that bored piling is

Jan 1, 1994

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By Garland E. Likins

High-strain dynamic testing of drilled shafts and cast-in-place piles has become routine procedure in many parts of the world today. Field testing is performed by measuring strain and acceleration records under impact of a falling mass. Wave equation analysis is utilized to design the weight, drop height and cushion of the hammer apparatus to assure a successful test. The Pile Driving Analyzer* (PDA) and CAPWAP* methods are used for data acquisition and analysis. Testing results yield information regarding pile static bearing capacity, structural integrity, and pile-soil load transfer and pile load-movement relationships. This paper discusses application of high-strain dynamic testing to cast-in-place shafts with emphasis on aspects unique to this type of pile. Suggestions regarding minimum requirements for good quality tests are offered. Five case histories reported in the literature are summarized and a sample specification is also included.

Jan 1, 1995

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By Bengt H. Fellenius

The bearing capacity equation?"the triple N formula"? is now about 50 years old. It was developed from theory of plastic resistance of metal to a cone being pressed into the surface of the metal, superpositioned by resistance due to shear in an interparticulate medium (soil; note, we are not dealing with metallurgy), and tempered by work necessary to move the footing into the medium. The equation (and its coefficients) was "confirmed" by tests on small footings placed at or near the surface of the soil. The equation is a basic tenet of every geotechnical textbook, manual, and code. Over the years, innumerable variations of the N-coefficients and adjustments to the equation have been published. The main assumption behind the bearing capacity equation is that a shear plane develops between two essentially otherwise unaffected bodies: the main soil body and a body comprised of the footing with some soil. Moreover, the notion is that a model footing placed at or near the surface of a soil would behave proportionally or similarly to a full-scale footing, or to even a same size footing (pile toe) placed at some depth in the ground. This is not in agreement with factual observations. It is suggested that the behavior of a small or large diameter footing as well as a pile toe is governed by compression of the soil below the footing or pile toe and not by "bearing capacity".

Jan 1, 1999

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2004

By Peter O. Wilkinson

Ascot Racecourse in the UK is a major international venue for horseracing. The racecourse is being redeveloped to provide entirely new public facilities. The development includes the construction of a new grandstand. A site investigation was earned out comprising mainly cone penetration testing. The site is underlain by the Bagshot Formation, comprising predominately cohesionless deposits of medium dense becoming dense, silty fine to medium sand, containing occasional layers of clay. Shallow foundations would present uncertainty regarding total and differential movement; hence a piled foundation solution was chosen using a continuous flight auger (CFA) piling system. The possibility that piles may found either directly on or within the influence of cohesive material suggested uncertainty regarding toe resistance. In order to measure shaft friction, an instrumented preliminary test pile was undertaken. The results were compared to published correlations of cone and shaft resistance. This approach resulted in a net saving in terms of pile length which resulted in optimum value engineering and hence a cost saving to the client.

Jan 1, 2006

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By George G. Goble

In the middle of the nineteenth century, the dynamic formula appeared as a description of pile penetration during impact driving. The simplicity of use of the formula combined with the power of the energy concepts behind the formula caused it to be quickly accepted and integrated into practice. Dynamic formula had been in use for 100 years when the Wave Equation computer programs first appeared. With that long experience it is not surprising that the formula continued to be used and were only slowly abandoned. The Wave Equation offers many advantages over the various formula but it does not offer a clear sense of physical understanding of pile driving that is available with the formula. Large amounts of numbers are generated but often it is difficult or impossible to gain a physical understanding of the results or a feeling for the importance of the various parameters. The question that the Wave Equation user has is, "What will happen if I use a larger drive cap (or change any other item of equipment)?" In this paper, I will attempt to explain pile driving using elementary wave propagation theory. However, the presentation will not depend on any higher mathematics. With the use of wave mechanics, it is possible to explain driving characteristics that cannot be handled with the energy formula.

Jan 1, 1995

Jan 1, 2001