Search Documents

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By J. D. Runkie, A. G. Lyle, G. A. Gillies

Tar evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis GRAPHS In Fig I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas In this instance the four curves are named, respectively the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve In these tests barite was the mineral concentrated, therefore a barite concentrate was produced Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions Percentage Rejection-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows Suppose a concentrate contains 5 per cent of an undesired mineral This indicates

Jan 1, 1942

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By R. C. Schmidt, B. E. Kennedy

The Mont Klahoyo magnetite deposit is located about 600 km (373 miles) northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 Mt (739 million short tons) grading 36% iron. The deposit occurs at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations with associated amphibolites, pyroxenites, and gneisses of the Liberian Shield. The ore body is represented by a highly metamorphosed banded quartz-magnetite iron formation with alternating beds of iron silicates and quartz-magnetite. Amphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated, overturned 2-shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m (427 ft) and outcrops intermittently over a distance of approximately 5.5 km (3.4 miles). Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K- 1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) while the remaining quartz-magnetite units are oxide facies, representing the important Mont Klahoyo deposit ores. Ore-bearing "K" units are subdivided further into 11 ore types, based upon their specific lithologies, iron content, and concentration characteristics. Identification of these ore types proved particularly useful to mine planning and flowsheet design. A cap of oxidized material overlies the primary quartz- magnetite iron formation, but no enrichment has occurred. It is thought that the Mont Klahoyo iron formations were deposited chemically in a volcanic environment as a siliceous iron formation with volcanism the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a coarse-grained, quartz-magnetite-silicate iron formation.

Jan 1, 1983

By L. W. Blau

THE entrance of geophysics and geochemistry into petroleum engineering may be viewed with apprehension by some engineers. They may not remember the time when "practical oil men" opposed the invasion of engineers into the field of petroleum production. By their excellent contributions they established themselves. In the popular mind, engis veers are practical men whereas physicists and chemists are suspected of being theoretical. It will be best to annihilate this misconception right now at the beginning of a closer relationship between petroleum engineers. geophysicists, and geochemists.

Jan 1, 1943

By R. F. Favreau, G. E. Larocque

The objective of the study is development of an analytic process based on rock and explosive properties which allows the prediction of the stress distributions and fracture zone around explosive charges. A computer program has been written for this purpose, using a finite difference approximation to the momentum equation, to describe the motion of the surrounding rock by step-wise integration. Its application provides ground motion data such as stress components, displacement and particle velocity as a function of position and time with respect to a spherical charge. The effect of tensile and shear failure on these ground motion parameters can be included. The analytic procedure contained within this program has been used to predict peak stress as a function of distance in rock for rock-explosive combinations for which field data exists to determine peak stress levels directly. Two methods have been used for the spherical charge which in the analysis replaces the actual cylindrical charges: instantaneous application of peak pressure to a charge having a radius equivalent in contained volume to a charge having a length to diameter ratio of 1, and gradual pressure build up to peak pressure with a charge radius equivalent in contained volume to the total charge used in the field test. The agreement with field data would appear best with the latter treatment. The peak stresses obtained are in closer agreement with field measured peak-stress and a better approximation to field stress wave duration exists in the case of gradual pressure build up. One of the assumptions made in the analysis is that, in the case of cylindrical charges, the explosion pressure rather than the detonation pressure of an explosive establishes the peak stresses in the

Jan 1, 1971

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

By W. H. Yarroll

This paper presents a general discussion of the utility of the statistical technique known as multiple correlation, and gives three specific examples of its application. The first demonstrates the most simple form, or straight-line, multiple correlation. The other two demonstrate multiple correlation analysis in best-fitting third-degree parabolas. With the increasing availability of digital computers, the method becomes entirely feasible where heretofore its use was impractical. The advantages of the method are discussed, and curves are presented which were developed by computerizing the regression equations developed in the examples. The method described in this paper is for use with complex systems, and the examples given are complex metallurgical systems. This subject falls under the general classification of cybernetics, which is defined' as "the science of control and communication, in the animal and the machine." Machine, in this case, can include chemical and physical processes which take place within machines and processing equipment of all kinds. The classical approach to scientific investigation has been the construction of simple models and the changing of variables one at a time. This method is wholly inadequate for obtaining useful information from the complex systems of modern technology including many of our flotation and hydrometallurgical processes. Cybernetics offers the method by which complex systems which have been implemented as an art in the past can now be analyzed with all the discipline of a science. Mathematical techniques for achieving multiple correlation analysis have decided advantages over some of the other statistical methods.2-4 Multiple correlation does not require a series of experiments that have been rigidly planned as do many of the other statistical methods. For this reason, it can be used effectively for interpretation of information from op- erating plants, where planned experiments are impractical, as well as for laboratory experiments. First-degree multiple correlation has been used for many years, and was useful, but limited to linear or nearly linear relationships. The technique described in this paper provides a method for analyzing systems which may be non-linear. This particular technique is multiple correlation analysis in best-fitting third-degree parabolas. It is quite possible that lack of reference to the technique has been due to the overwhelming mass of computations it requires even for relatively simple problems. With the advent of computers, however, its use has become entirely feasible. For the benefit of those who may not be familiar with the subject, it might be well to pause at this point to discuss multiple correlation analysis — what it is and what it achieves. To go back to the old familiar fitting of a set of points with a best-fitting straight line by the least squares procedure, it is conceded that this a good method where there is only one independent variable influencing the dependent variable under consideration, and providing that the relationship is linear. In most fields of investigation, however, there are usually a number of factors exerting important influence, and they frequently bear relationships with the dependent variable other than straight line. Under these conditions, it is easy to see how misleading a simple correlation study might be. Multiple correlation can be used for any number of variables. Within the experience of the writer, this technique has been used to establish regression equations for determination of carbon rate, burden permeability, and production rate on iron blast furnaces, production rate on open hearth steel furnaces, life of molds for steel ingots, rolled steel tensile strength and various defects in rolled products, the performance of ore dressing equipment, and optimization of extractive metallurgical process variables. The discovery of mathematical correlation does not prove, per se, true cause-and-effect relationship, but simply establishes a hypothesis. If the regression equation can be used to make successful predictions of what will happen with future arrays of independent variables, then one can feel reasonably assured that true cause-and-effect relationships have been discovered.

Jan 1, 1968

By James Gayley

The atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantitiee. At no time since the blast-furnace became an important and widely used apparatus—even when it was operated in the most crude manner—have the variations in composition of the raw materials used been as frequent and as great as the variations in humidity of the atmosphere. Important improvements have been made in the blast-furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing-engines, the increased protection given to the bosh-walls, and the careful preparation of the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least, a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humidity as variable to-day as when first blown into a primitive blast-furnace, appeared to stand as a barrier to

Jan 1, 1905

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By Marcus A. Grossmann

This paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron. Absence of Carbon We may turn at once to the effect of the presence of alloys. It has been found that in the complete absence of carbon, the gamma change will sometimes disappear entirely when sufficient alloying element is

Jan 1, 1927

By Cyril Wells, Robert F. Mehl

The purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2o C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made2. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsenl that variations as great as 30' C. exist in the reported data on the A3 temperatures in iron-carbon alloys. Fortunately, the Aa temperature in pure iron is now known to be 910" C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato5 on both hypoeutectoid and hyper-eutectoid steels. Esser made a dilatometric and magnetic study of iron and iron-carbon alloys containing 0.06 to 0.86 per cent C, for which a high purity is claimed. Presumably the electrolytic iron was reasonably pure, but the alloys contained considerable impurities, on the average totaling 0.35 per

Jan 1, 1937

By H. M. Howe

It has seemed to the writer that one important, and indeed sufficient reason, for our slow progress in learning the relation between the chemical composition and the physical properties of cast-iron, has been that the problem has not been attacked properly. It would be well to select the most probable working hypothesis which we can find, and proceed to test that hypothesis by comparison with observed facts, and by making new observations specially designed for such a test. Our first step, then, is to select the most probable working hypothesis ; and to attempt this selection, to state the hypothesis and its immediate corollaries, and to take some first steps toward testing it, is the object of the present paper. Its chief purpose is to bring the hypothesis to the attention of those who are more familiar with the evidence than the writer can pretend to be, and in a better position both to present new evidence and to discuss it. The hypothesis here selected is, that composition governs properties in the case of cast-iron, in the same general way and for the same reasons as in the case of steel, mutatis mutandis. This hypothesis, which of course makes no claim to originality, certainly seems reasonable and probable; its exposition and discussion are made easy by our existing knowledge of the constitution of normal or " carbon " steel; it therefore seems worthy of consideration.

Jan 1, 1902

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineralized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissipate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By C. S. Smith

It is the policy of The Metallurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editor, Dr. Gerhard Derge; Editorial Assistant, M. A. Redmyrski; Staff Coordinator, James J. Burke. THE METALLURGICAL SOCIETY: W. R. Hibbard, Jr., President; J. C. Kinnear, Jr., Post-President; John Chipman, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretory. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Chairman- Dennis Carney John Chipman J. C. Fulton J. H. Hollomon H. H. Kellogg, A. E. Lee, R. Moddin, J. D. sullivan, and D.' Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: T. B. King, Chairman; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr., and P. T. Stroup. lnstitute of Metals DM lion: Robert Maddin, Chairman. F. Lincoln Vogel, Jr.. Vice chairman. W. A. Backofen R. W. Boliuffi J. H. Bechtold' M. B. Bever R: S. Busk C 6. Goetzel poul Gordon C. D. Grobom, Jr., Robert F. Hehe-mann R. I. Joffee F. i. Joumot Jr. lrvin R. Kromer, A. J. Leno. Horold Morgolfn, C. J. McHargue, Russell A. Meussner, J. B. Newkirk, H. W. Paxton, G. E. Pellissier, I. S. Servi, Alon U. Seybolt, A. J. Shaler, and Jack Washburn. Iron and Steel Division: J. C. Fulton, Chairman. T. B. King, F. C. Laogenberg, W. O. Philbrook, and T. 0. Winkler. Publishod bimonthl by the American Institute of Mining Metollurgicol and Petroleum Engineers Inc., 29 West 39th Street, New York 16, N. Y. Telephone: PEonylvanie 6-9220. Subscription $20 par yew for non-AIME members in United States and North, South and Control Americo $25 foreign; $5 for AIME members. Single copies, $4.00, single copios foreign $5,00. The AIME is 1958 by the Amarican mode or opinion axpressed in it* publications ... Copyright by the Amarican lnstitute of Mining, MataIlurgicol, and Petrolum Engineers, Inc,. . . Reg. istered cable address AIME New Yark ... Indexed in Engineering Inderx, Industrial Arts ...Index and Chemicol Number5. Absrtracis . . . Second class postage paid at New York,Indor. N. Y., Industrialond Ann Arbor, Mich.

Jan 1, 1959

By James Johnston

Synopsis.-A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably. complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the, processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at. 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their . high-grade ore,1 the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partial amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company's Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000.

Jan 1, 1914

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

By T. E. Eagan, W. R. McCrackin

IN dealing with segregation in babbitt, and its effect on the final cast structure, which is a bearing, it is obviously impossible to cover all of the compositions manufactured. Each composition, of course, will exhibit certain specific types of segregation. However, as examples,, two compositions of babbitt are presented: one a tin-base of well-known analysis and the other a lead-base, which in the past few years has found wide usage. Bearings usually are cast either statically or centrifugally; therefore the effect of these two methods on segregation is presented. EXPERIMENTAL PROCEDURE A slab of babbitt 1/2 in. thick by 5 in. wide and 17 in. long was cast, using a book mold with the long edge vertical. An A.S.T.M. grade 2 babbitt was used (3.5 per cent copper, 7.5 per cent antimony, remainder tin), to which 0.10 per cent tellurium had been added. Unfortunately, no metal without tellurium was available. The mold to hold the babbitt was heated to approximately 300°F., the temperature being judged by the babbitter. The pouring temperature of the babbitt was 875°F. (470°C.). One slab was made by allowing the babbitt to cool without stirring. The other slab was stirred during the entire cooling cycle. This stirring consisted of a vigorous churning or puddling into the mold until complete solidification had taken place. Three samples were removed from these slabs. One was taken at the extreme bottom, another half way to the top, and another at the extreme top, all at the center of the width. Chemical, macroscopic and microscopic examination was made of all samples. Table I shows the chemical analyses obtained at the described positions [ ] in the slab. The analyses show no serious amount of gravity segregation. Microscopic examination from edge to edge of the slab showed little change in structure. From top to bottom there was a progressive coarsening of the grain size in the stirred slab but little change in the slab that was not stirred (Fig. I). No definite exhibit of segregation could be detected. In line with our experimental study on the tin-base babbitts, we cast an almost duplicate slab using A.S.T.M. Alloy No. 15, containing 0.9 to 1.25 per cent tin, 14.75 to 15.5. per cent antimony, 0.80 to 1.25 per cent arsenic and 0.4 per cent copper. The slab was 16 in. long and 3/8 in. thick, cast with the long side vertical. One slab was allowed to cool normally and the other was stirred continually during cooling. The pouring temperature of the babbitt was

Jan 1, 1944