Search Documents

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

"The Hardy Cross algorithm offers a reliable method of solving network systems of fluid flow and has become widely used for solving water and ventilation flow networks. A limitation is that computational iterations and time to solve a network rises rapidly with the size of the model and modern detailed ventilation networks have typically grown to thousands of airways. Non-linear matrix solving methods can offer improved performance, however these are more complex and may be unstable if initial estimates are poor. This paper presents improvements that can be applied to the traditional Hardy Cross algorithm to greatly reduce iterations and solving time for large ventilation models. INTRODUCTION The Hardy Cross algorithm (Cross, 1936), was originally developed to solve water flow in city and urban pipe networks. Using principles of Kirchhoff’s electricity current laws, Hardy Cross developed an iterative algorithm for solving non-linear equations associated with network water flow. Traditional network analysis research refers to the various members of system networks as branches, nodes and meshes. This terminology has been changed in this paper to airways, junctions and loops respectively which are terms more familiar to engineers in mine ventilation. When Kirchhoff’s laws are applied to fluid networks, the following assumptions can be made: •The sum of fluid flows into a junction must equal the sum of fluid flows out of the junction.•The sum of pressure losses around any loop through a network system must be equal to zero.An iterative solution can therefore be achieved by initially guessing flow in a network, calculatingthe pressure losses around the network loops (Figure 1), and applying flow corrections using Newton’s method for each loop if the sum of the pressure losses does not equal zero. To solve the system, a loop must be defined for every segment or series of segments between a junction of 3 or more airways.The Hardy Cross algorithm has been used extensively for ventilation network analysis since the introduction of the first electronic computers (Tien, 1997), however numerous other variations and methods have since been developed through the use of matrices to solve the required system of nonlinear equations. Commonly used algorithms such as the Newton Raphson method (Brown, 1969), the Gradient method (Todini & Pilati, 1988), the Linear Theory method (Gupta & Prasad, 2000), and Coupled Network Solver (G. Danko, 2008) have found general use in fluid flow network solvers (Rossman, 2000). Despite poor and sometimes unpredictable convergence performance however, the Hardy Cross algorithm still has unique properties that make it attractive for ventilation models. Some benefits are:"

Jan 1, 2019

By Ph. D. Favreau, Favreau Patrice B. Eng, R. F.

Geology is important in mining by helping to identify the rocks which contain sufficient valuable ore to justify their excavation. Geologists give a geological name to each rock type, so geology is a player in blasting; when a blaster has successfully blasted rock of a given geological name at a former site, and he later has to blast rock at another site whose rock has the same geological name, then his first trial often is the same method as he used at the former site, since the geological name of the rock is the same

Jan 1, 2019

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

By Catherine T. Aimone-Martin, Elena Oana Jacobs, Brent Meins

Accurate pressure measurements during underwater detonations are critical for the protection of structures and mitigating impacts to fish and marine mammals. Current guidelines that limit underwater pressures are based on past studies, many of which used sample rates of 48 and 65 kS/s (48,000 and 65,000 samples per second). These sample rates may be insufficient to accurately record high frequency, sharp rise time blast pressures. As such, pressure thresholds associated with fish and marine mammal injury or mortality may be underestimated, calling into question the pressure and sound pressure level guidelines that govern underwater blasting today.

Jan 1, 2019

By C. Cristonffanini, S. Nazari

"In the past, simulation was considered to be an offline tool disconnected from plant operation. Advancements in the computation power combined with utilizing physics and chemistry sciences have allowed us to significantly improve the modeling and simulation technology for mining and mineral processing. This paper investigates the benefits of first principle models and simulation by connecting them to real time operation. Process data are connected to high fidelity models executed in parallel to the operation. In recent literature, this concept is known as Digital Twins. The Digital Twin is used for various purposes such as optimization, virtual instrumentation and condition monitoring. Using IDEAS™ simulation software we are able to construct a digital twin for different equipment inside a mineral processing plant. Two case studies for building a digital twin for the primary hydrocyclone feed pump and thickener underflow are presented. Using the pump’s model, a digital twin is developed and is installed in a gold extraction plant that is able to infer the slurry density in real time. Additionally, it is used for detecting sanding in the pipes and impeller condition monitoring.INTRODUCTION Since the eighties, thanks to advances in computation technologies, computer based simulation of processes using first principle models has become a well-known engineering tool for various industries. As our understanding of processes has increased, their representative models have become more realistic and more sophisticated. Due to this increase of accuracy, use of simulation is becoming more fundamental in process industries. The main goals to use accurate simulation is to decrease the engineering and construction cost, optimize the process design and improve the operation performance by decreasing operation cost and increasing efficiency. The term Digital Twin was first introduced in 2010 by NASA (Shafto et al., 2012) in aerospace industry. Subsequently, the concept quickly spread through other industries. As of today, no standard organization has provided an official and unique definition of Digital Twin for process industries. However, there are three important aspects that are common throughout various descriptions. When simulation is core functionality of the process (1) along the entire life cycle of the plant (2) with direct linkage to operation (3), it is called that process has a Digital Twin. According to Gartner, the concept of Digital Twin has elected as fourth most important disruptive technology for the year 2018 (https://www.gartner.com/, 2017)."

Jan 1, 2019

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By M. Li, T. H. Dubaniewicz, H. N. Dougherty

"INTRODUCTION Underground mines have the risk of accumulation of gases if not ventilated properly or during and after emergency situations when ventilation controls become damaged or stop working. Common gases that are monitored in underground coal are carbon monoxide (CO), oxygen (O2), and methane (CH4). Methane is a gas found in coal and released through mining; its explosive range is between 5% and 15%. Methane is commonly monitored on all mining equipment and with handheld gas sensors carried by most underground coal miners. Fiber optics (FO) is a popular technology applied in underground mining, particularly for its electric isolation. Many miners are familiar with FO cables hung throughout the mine, which are primarily used in the communication of voice and data (Taylor et al. 2010). Advancements in laser and fiber optics have made this technology well suited for gas sensing the harsh environment of mining applications. The work of the U.S. Bureau of Mines on the use of fiber optic monitoring of gases in mines started in 1992. Dubaniewicz et al. (1992, 1993, 1995, 1999, 2003) developed prototype gas sensors, including methane gas sensors, for research purposes. Previous research (Dubaniewicz & Chilton 1992) identified potential fiber optic gas detection cross-sensitivities associated with the index of refraction of various gases. Index of refraction effects was noted for carbon dioxide (CO2), which is produced in significant quantities by mine fires or explosions. NIOSH released a broad agency announcement (BAA) for the development and demonstration of mine safety and health technology (CDC NIOSH 2017). The objective of this announcement was to validate a sensor, specifically fiber optic, for the mine environment and test it in an actual working mine. The RSL FO sensor “OptoSniff” provided from this work is capable of hundreds of sensing points over distances of up to 20 km, has a measurement range of 0.05% to 100%, senses in an oxygen- deficient environment, and has no gas cross-sensitivity (RSL, 2014). The RSL system is totally electrically passive outside the central control unit (CCU), which can be housed in an MSHA-approved explosion-proof (XP) enclosure or in a control room outside of the permissive area. The sensor was tested in dusty and signal loss situations, showing it is tolerant of dust, has functioned at signal losses up to 90%, and was successfully tested in a mine environment for a five-month period (Walsh et al. 2014). This paper describes how the RSL FO sensor is used for testing using smoke and its contaminants for applicability in emergency situations. The testing investigates individual contaminants such as CO2, temperature, and smoke. Each test was performed separately and methane concentration, laser power, and response time data were collected."

Jan 1, 2019

By Sushil Bhandari, Amit Bhandari

Blast optimization in open-pit operations is a task that often remains at a theoretical stage. Indeed, when it comes to operational blast design and onsite implementation, time restrictions and field conditions make it difficult to execute a planned pattern accurately and optimization according to local conditions is even more difficult. For example, adjusting a drill pattern to a complex face geometry is not something that can be easily undertaken on site. Blasters and engineers will do their best trying to distribute boreholes over the bench and even then, it can take them hours to achieve an acceptable layout. Similar situations occur with delay sequences, when trying to adjust them to address selectivity or vibration issues. For these reasons, operational blast design will often remain at a very basic level and the required adjustments are laid aside due to the difficulty of implementing them on site.

Jan 1, 2019

By Andrew Artzer, Michael Moats, Jack Bender

Antimony and bismuth in copper electrorefining electrolytes can cause cathode contamination, leading to the careful control of their concentrations. This study examined the laboratory scale removal of bismuth and antimony from an electrorefining electrolyte using a solvent extraction mini-pilot plant. The ability of a proprietary phosphonic acid ester extractant (REX-2) in a commercial diluent was studied in a simulated commercial setting. Antimony and bismuth were both extracted effectively from the electrolyte (72% Bi and 70% Sb removed) and Bi was effectively stripped (92% Bi recovered) with 400 g/L sulfuric acid. A final strip solution was obtained from the SX circuit containing 0.36 g/L Bi, 0.043 g/L Sb, 1.3 g/L Cu, and 0.18 g/L As. Unfortunately, most of the extracted Sb remained in the organic phase. Following the pilot study, experiments were performed to examine the precipitation of bismuth from the aqueous strip phase and the removal of antimony loaded on to REX-2. INTRODUCTION For many years, antimony and bismuth have been some of the most problematic impurities in copper electrorefining (ER) (Bardwell & Lapee, 1933). Along with surface roughening, high concentrations of Sb and Bi can contaminate the copper cathode and precipitate at the copper grain boundaries. This drastically reduces the drawing ability of the metal (Bender & Emmerich, 2016). For these reasons, it is necessary to control Sb and Bi concentration in the cathode, which is done by controlling their concentration in the electrolyte. Conventionally, Sb and Bi concentrations are controlled by maintaining a proper As/(Sb+Bi) molar ratio in the anode and arsenic concentration in the electrolyte. Antimony and bismuth are removed during electrolyte purification using liberators (electrowinning cells) and/or ion exchange. Liberators treat an electrolyte bleed stream from the ER circuit and electrodeposit increasingly impure copper as the copper concentration of the solution decreases. Traditionally, first stage liberators reduce the copper concentration from ~45 g/L to ~15 g/L and produce saleable copper. Second stage liberators decrease the copper concentration to ~8 g/L (Biswas & Davenport, 1980) which results in contaminated cathode that is returned to anode production (Biswas & Davenport, 1980; Wang, 2004). Further electrolyte purification is not always required but third stage liberators can be used to reduce copper concentration below 2 g/L which results in significant removal of As, Sb and Bi and very impure deposits which are recycled to a smelter or used for As production. However, liberators do not have very high energy efficiency (Acharya, 2014; Ando & Tsuchida, 1997) and below 0.5 g/L copper, highly toxic arsine gas may form (Biswas & Davenport, 1980).

Jan 1, 2019

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By Greg Canivan, Bernie Hertlein, Les Chernauskas, Joram Amir, Garland Likins, E. Anna Sellountou, Tim Kovacs, Peter Kandaris

Nondestructive testing of drilled shaft foundations via Crosshole Sonic Logging (CSL) is often performed as part of the quality assurance process to assess the soundness of concrete. The intent of CSL testing is to identify irregularities such as soil intrusion, necking, soft bottom, segregation, voids and other defects that could result in poor structural performance of the foundation. Over time, CSL rating criteria based on first arrival time and relative energy have incorrectly evolved to often be the sole means of determining the acceptability of a shaft. Some of these criteria have found their way into regulatory agency specifications, with acceptance values often differing from agency to agency.The purpose of this document is to review the state of the practice (including experience gained over the past 20 years), propose improved CSL rating criteria and make recommendations for additional assessment, as well as educate the industry on the proper interpretation of CSL test. CSL test results alone should not be the sole means of rejecting or accepting a shaft. A task force of industry exerts was formed to review the existing CSL rating criteria and propose improvements where appropriate. The recommendations presented herein are the consensus of the task force, which believes that they should be incorporated into future criteria, codes and specifications. This paper was produced as a joint effort between the Codes and Standards Committee, the Drilled Shafts Committee and Testing and Evaluation Committee. A task force was authorized under Testing and Evaluation Committee. The task force contributed their expertise in web-based discussions often every two weeks over a period of three years. Interested participants were invited to participate at any time. The document had two rounds of broad industry review, two rounds of DFI Technical Advisory Committee reviews, and a Public Comments process. All comments were considered in producing the final document.

Jan 1, 2019

By Y. X. Li, L. R. Xiao, S. Gong, S. S. He

Porous copper and porous copper based alloys with controllable pore structure have been manufactured successfully by sintering evaporation process. This process consisted of mixing copper or copper based alloys with NaCl powders, hot pressing and final high-temperature sintering to evaporate the filler material of NaCl powders. NaCl was eliminated completely during vacuum sintering, and strong metallurgical bonding in the walls was achieved. The pores’ structural parameter (pore size, shape, and direction) and porosity can be controlled effectively. These porous copper and porous copper based alloys with controllable pore structure have great potential in many fields. Including heat dissipating materials, heat absorbing materials, chemical catalyst carriers, electromagnetic shielding materials, filtering materials, damping materials, silencing materials, battery electrode materials. INTRODUCTION The development of porous materials began in the 1960s. The research of activated carbon with high specific surface area made porous materials enter the stage of material research (Belyakov et al., 2008; Ferey et al., 2008). With the rapid development of science and technology, porous materials play an important role in material research, and gradually become an indispensable part of the material research field (Wu et al., 2012). The research of porous materials has gradually extended to metal, ceramics, plastics and glass and other fields. It has been successfully applied in many fields, such as functional materials, industrial production, aviation, medical materials, biochemistry and electronics, which fully shows that porous materials have considerable development prospects. Porous silicon, plastic porous materials and glass porous materials are the most widely used in the field of non-metallic porous materials (Capelle et al., 2012). Compared with non-metallic porous materials, metal porous materials have developed rapidly in the late 1980s and become new materials with good mechanical properties and excellent physical properties. Porous metal materials have many advantages, such as large specific surface, small specific gravity, good silencing effect, high stiffness, high electromagnetic shielding performance, good shock absorption performance, etc (Li et al., 1999; Ferey et al., 2008). Among its many applications, metal porous materials can be used as both functional materials and structural materials. In some cases, metal porous materials have dual functions and structures. It is a multi-purpose engineering material with excellent performance. At present, porous copper, porous aluminium and porous nickel are the most concerned materials (Chen et al., 2002; Yang et al., 2017; Liu et al., 2018). The preparation methods of porous copper and copper-based alloys mainly include self-propagating high temperature synthesis (SHS), capsule-free hot isostatic pressing (CF-HIP), spark plasma sintering (SPS) (Kvanin et al., 2008; Takahashi et al., 2008; Zhang et al., 2014). However, these methods can not accurately control pore structure parameters (including pore size, shape, orientation, distribution, etc.). In porous materials, pore structure plays an important role in the overall performance of materials. In order to control pore structure parameters accurately and optimize material performance, it is necessary to explore and develop new preparation technology. In this paper, the sintering evaporation process (SEP) was introduced for the preparation of porous copper and copper-based alloys. The core process of the preparation method is hot pressing and evaporative desalination. Hot pressing can make the pore orientation consistent. Evaporative desalination can ensure the complete removal of NaCl in the form of vapor in a short time, thus eliminating the corrosion of residual NaCl on the matrix metal (Gong et al., 2011).

Jan 1, 2019

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By David S. Graham, Paul J. Axtell

Crosshole Sonic Logging (CSL) non-destructive integrity testing identified anomalous readings near the base of a 6.5-foot diameter drilled shaft rock socket. The anomaly was confirmed to be a defect by subsequent coring and core hole camera inspection. A large void and exposed rebar were visually observed in one of the core hole camera inspections. The center of the shaft was then excavated initially with 3-foot diameter tooling and subsequently with 4-foot diameter tooling as part of the remedial actions to address the defect. While excavating with 3-foot diameter tooling, the shaft defect was not encountered. Excavation with 4-foot diameter tooling revealed the defect, a significant void around the majority of the shaft circumference. The void extended radially from the circumference of the 4-foot diameter excavation to beyond the reinforcement cage to the exposed wall of the rock socket around approximately 80 percent of the shaft circumference. CSL results and observations made during remedial shaft investigation and excavation are in good agreement. The shaft defect, located primarily outside of the reinforcement cage, was effectively identified by CSL testing. Although the defect was confirmed by investigative coring, the remedial excavation demonstrates how the investigative coring could have easily missed the defect. This paper shows how CSL results compare to physical observations made during a rare opportunity to characterize the full extent and nature of a drilled shaft defect originally identified as an anomaly by CSL testing. INTRODUCTION The case history presented here pertains to a drilled shaft for a multi-shaft bridge pier in the Midwestern United States. However, the observations presented in this paper are not a result of unique site conditions or the particulars of the project. The lessons learned from this case history are applicable to almost any drilled shaft constructed in the wet. The overall length of the subject shaft is 22 feet including approximately 12 feet of permanently cased, 7-foot diameter shaft extending to bedrock and approximately 10 feet of uncased, 6.5-foot diameter rock socket. The shaft is designed to resist axial and lateral loads and considers the contributions of side and base resistance in the axial design. Six, 2-inch diameter steel Crosshole Sonic Logging (CSL) tubes are include in the shaft. The bedrock at the shaft location includes beds of sandstone, shale, and limestone. The shaft was drilled using conventional drilling equipment and tooling, and water was used as the drilling fluid. Conventional drilled shaft concrete appropriate for underwater tremie-placement was placed via a 10-inch diameter open hopper tremie.

Jan 1, 2019