Search Documents

By A. W. Fahrenwald, Lewis S. Prater

BY taking advantage of the fundamental difference between screening and classification-namely, that specific gravity has no effect on screening but is one of the important factors in classification-a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from 3/8 to 1/2 in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard [v2]series. The accompanying flowsheet gives the testing procedure followed. [ ]

Jan 1, 1945

By G. M. Savov

Copper recovery via Solvent Extraction (SX) process is a well-known technique, which is practiced commercially for approximately 40 years. The main advantages of the SX process are: an absence of using high temperatures (not more than 50oC), complete recycling of barren solutions, very high selectivity at removal and purification of metals, metal conversion to a form, suitable for easy subsequent recovery. Despite the wide acceptance of Solvent Extraction, it does have some shortcomings, namely SX employs large quantities of volatile organic substances. This leads to huge plant ?footprint? of SX circuits. The SX is very sensitive to low temperatures and quantity of total suspended solids in feed solutions and this causes bad phase disengagement times and therefore poor process performance. And most important ? low grade solutions (with copper concentrations below 1 gram per litre) are very unattractive for treatment via Solvent Extraction process, because capital costs for SX plants are not a direct function of copper tenor in the feed. The combined process with Ion Exchange (IX) and Solvent Extraction ? further called IX/SX by IONTECH Engineering was developed. This combination eliminates SX negative characteristics shown above. The key findings of the IX/SX process are; (1) recovery of copper from pregnant leach solutions with metal concentrations, varying on a broad range; (2) can be operate effectively with very low-graded copper pregnant leach solutions; (3) the construction of large ponds for pre-filtration of the pregnant leach solutions is not necessary; (4) working with turbid solutions and solutions containing large quantities of suspended solids; (5) winter operation without troubles; (6) strongly reduces organic losses; (7) technological approach lead to plant sizes reducing. This paper reviews the main stages of the combined IX/SX process, the applications for metal recovery and introduces projects where the process is applied. Key findings of the process are also presented. A comprehensive technical comparison between processes has been carried out. This paper also evaluates the advantages of using combined IX/SX technology as a purification and separation step in copper production process, with the aim of further increasing the overall copper recovery and to ensure that a suitable copper concentration in the advanced electrolyte is achieved. The implementation of a Ion Exchange (IX) process in the classic Solvent Extraction-Electrowinning process(SX/EW) is found to be beneficial for processing of pregnant leach solutions both from spent and new copper heaps and dumps, acid mine drainage and other industrial streams without any preconditioning as well as in terms of achieving improved recoveries and copper cathode quality.

Sep 1, 2012

By V N. Rudashevsky, F Melcher, J Lodziak, D Klosa, N S. Rudashevsky, M Sitnikova, L Gast

A combination of novel and æclassicÆ methods, namely electric pulse disaggregation (EPD), hydroseparation (HS), preparation of monolayer polished sections, and mineral liberation analysis (MLA) was employed to study ores from platinum pipes (Bushveld Complex, South Africa), pristine PGE mineralisation of the Main Sulfide Zone (Great Dyke, Zimbabwe), as well as ancient and modern gold/PGM placer deposits. It is shown here that the EPD technique liberates mineral grains of interest without any visible destruction allowing the study and analysis of individual rock-forming and ore minerals, in our case especially platinum-group minerals. The HS method is an effective tool in concentrating heavy minerals by factors up to 10 000 fold. As near-total recovery of grains >10 ¦m is achieved, the nugget effect can be overcome also in case of limited availability of samples (drill core, museum specimens). The MLA technique is a fast tool to detect and characterise mineral phases in ores and ore processing products. Many mineralogical parameters of individual grains and mineral assemblages can be deducted and documented. The results show that the techniques employed, either on their own or in combination, provide a wide range of additional information especially on platinum ores which is beneficial to both the researcher and the metallurgist.

Jan 1, 2008

By Junius D. Edwards

WHEN Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipments through the Caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. BAYER PROCESS The Bayer process has been almost universally used for the 'production of alumina from bauxite. This process, in outline, comprises the digestion of finely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium aluminate and the impurities-oxides of iron, titanium and silicon-remain undissolved. The undissolved residue, known as "red mud," from its color, is separated and run to waste. Aluminum hydrate (A1202.3H20) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1945

By Ralph H. Sweetser

AT the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rejections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blast furnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of the operational variables on the concentrate grade, recovery, separation efficiency and kinetic parameters of the copper flotation process. The results indicate that concentrate collecting time and pulp density were the parameters with the greatest effects on the concentrate grade. Considering copper recovery, the concentrate collecting time, collector dosage and pulp density were the most significant variables, in decreasing order of importance. The separation efficiency was found to be mainly influenced by the concentrate collecting time. This study can be helpful in identifying the parameters with the most effects on flotation performance and, consequently, the overall process efficiency, including recovery and separation efficiency. Such an outcome can be used as a decision-based tool to apply the necessary changes in a real-life industrial operation in a more effective way to improve the quality and quantity of the flotation concentration.

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By V. G. Minenko, V. A. Chanturiya, A. L. Samusev

Eudialyte is one of perspective resources of zirconium and other rare earth elements (REEs). Large reserves of eudialyte concentrated in the Murmansk region of the Russian Federation. Usually, technologies of REE treatment include the decomposition of eudialyte concentrate in different acidic, extraction and utilization of all components. The main problems in the leaching of eudialyte include are: the formation of an unfiltered silicon-containing gel; low recovery of REE; difficulty extraction of metals from the productive solution; high aggressiveness of the reagents. One of the promising trends of intensification of the processing of hard-to-degrease rare metal raw materials is the use of energy methods for affecting mineral suspensions. These methods make it possible to increase the efficiency of break up fine-dispersed mineral complexes and extracting micro- and nanoparticles of a valuable component in subsequent deep processing. The purpose of this work is to investigate the effect of energy impacts on the nitric acid leaching of eudialyte concentrate. Experimental studies were carried out in a developed laboratory facility that makes it possible to evaluate the effect of electrochemical, ultrasonic and combined effects on the leaching of zirconium and REE from eudialyte concentrate. The studies carried out on the samples of eudialyte concentrate with the size class of -0.315 + 0.063 mm showed that the use of electrochemical and acoustic effects increases the extraction of ZrO2 in the production solution in 1.6 - 2.5 times, REE in 1.3 - 2.2 times, respectively. An analysis of the microstructure and phase composition of the surface of the eudialyte concentrate showed that the intensification of the leaching process is due to surface cleaning from the silicon-containing gel, as well as the opening of capillary channels and microcracks, which accelerates mass-transfer processes. The results obtained open wide opportunities for creation of modern and effective technology of processing of eudialyte concentrate, producing high-quality zirconium products and REE.

Jan 1, 2018

By Brian Wyatt, Neil Webb, Marcel Roche, John Thirkettle

Recent developments in survey techniques and measuring equipment now allow for an accurate assessment of external coating condition and cathodic protection performance. These developments build on 20 years of experience of using Direct Current Voltage Gradient (DCVG) and Close Interval Potential Survey (CIPS) methods. The techniques use the latest advances in measurement systems coupled to a bespoke data processing system. The paper describes tests and trial surveys carried out on a hydrocarbon transmission pipeline in West Africa during 2005. The survey works described and conclusions drawn are from the data collected. Of particular interest are the apparent capacitance effects which are thought to occur under disbonded coating and the characteristics that these may show on the integrated CIPS and recorded DCVG profiles. This paper was originally presented at the Cefracor conference in Aix, France, in June 2006 The pipeline was originally installed on a phased basis between 1989 and 1994. The external coatings were three layer polyethylene factory coating and shrink sleeve field joint coating. An impressed current cathodic protection system was installed. The pipeline has subsequently been affected by disbondment of the coatings. It was a primary objective of the trials to attempt to identify such affected areas. In addition to a technically detailed account of the survey works undertaken and the results obtained the authors will consider the practical and commercial aspects of these surveys with input that provides a perspective from the specifier, pipeline surveyor, pipeline operations personnel and the pipeline owner. It is intended that the data presented will provide greater awareness of the benefits and limitations of the techniques used and their role for both stand-alone interpretation and the integration of the survey information with other inspection methods used for external corrosion assessment. The application of the described techniques is well developed and proven to locate and characterise through?coating defects and to provide a full audit of cathodic protection status. However, the possibility of the techniques being able to indicate disbonded coating is unproven and further tests and trials are planned which may allow a greater understanding of the electrical characteristics which are believed to be associated with disbonded coatings which may or may not be filled with an electrolyte. Further work is currently planned in West Africa, South Africa and Scotland in order to improve the understanding of this technique and to determine if the reported indications do actually represent a method of locating disbonded coatings. Keywords: External Coating, Cathodic Protection, DCVG, CIPS, corrosion assessment.

Jan 1, 2006

Combined Flow Sheet for Treatment and Recycling of Municipal Solid Waste (MSW) with Complex Morphological Composition

Sep 13, 2010

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By SANJIT KUMAR PAL, Sarvesh Kumar, Arindam Guha

The integrated geophysical study around pipe 1 and pipe 2 in Wjarakarur Kimberlite Field (WKF) assisted in comprehending the response of pipes. In the present study, we have attempted a combined analysis of very low-frequency electromagnetic (VLF-EM), electrical resistivity tomography (ERT), and magnetic methods to analyze the response from pipe 1 and pipe 2. A comparative analysis along all the profiles revealed the extension, depth, and geometry of the pipes. The results of VLF data and ERT data have been compared for two profiles of pipe 1 and pipe 2. Fraser-filtered grid map generated from all profiles of pipe 1 proficiently demarcated the trend of kimberlite pipe extension with high Fraser filter value associated with kimberlite. The ground-based magnetic data around pipe 1, pipe 2, and pipe 6 have been processed to analyze the magnetic behavior and subsurface structure based on the susceptibility contrasts. Analytical signal (AS) map revealed the extension of pipes, which was validated with the Fraser-filtered grid map. Analytical signal anomaly pattern reveals that pipe 1, pipe 2, and pipe 6 are trending in SW-NE, NE-SW, and NE-SW, respectively. Based on this study, the results indicate the conducting nature of pipe 1, whereas pipe 2 is resistive in nature. Further, the Euler deconvolution technique has been applied to calculate the possible depth of pipes from magnetic data. The comparisons of calculated depth ranges obtained from all geophysical techniques correlate well and validate the result (Table 1). The geological borehole data at pipe 1 and pipe 2 reported by the Geological Survey of India are well corroborated with our combined geophysical study.

Jan 17, 2024

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024

By Claude Bazin, François Robichaud

The control of the operation of a semi autogenous grinding mill is mainly based on power and bearing pressure measurements. Image based sensors can provide on-line measurements of the size distribution of the ore feeding a SAG mill allowing the control of this variable that impacts the operation of this equipment. This paper investigates the potential of using the information from such type of sensor to maintain a SAG mill feed target size distribution by manipulating the speed of the ore extractors below an ore stockpile. A PID and adaptive predictive controller for the size distribution are studied using a simulator for a stockpile and the equipments used for ore withdrawing from the pile. The proposed controller is found to give a good performance while remaining easy to tune.

Jan 1, 2014

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By S. Srinivasan

Traditional pit optimization techniques cannot take account of the requirement to blend ore in order to produce a saleable product, as is the case for iron ore, coal, limestone and other industrial minerals. Various techniques are proposed to overcome the deficiencies, many of which have been tested. The techniques in general involve the combined application of pit optimization and blend optimization techniques.

Jan 1, 1996