Search Documents

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By Jiling Wang, Xuefeng Liu, Haojian Duan, Lifeng Zhang, Ying Ren, Wen Yang

"In order to study the influence of MgO-C refractory on steel cleanliness and inclusions during steelmaking process, and to understand the reaction mechanism deeply, laboratory deoxidation and equilibrium experiments were respectively performed in MgO crucibles at 1873K. In the former experiment, after Al addition, steel samples were taken at different holding time. In the latter experiment, different slag components and different contents of carbon and aluminum in steel were considered respectively. The inclusion characteristics of each experiment were analyzed. The results showed that with the increasing of holding time after deoxidation by Al, MgO existed in the small inclusions firstly, and then in the large ones such as the clusters. The MgO content in the inclusions increased with the increasing of holding time, indicating that the MgO in crucible could be individually reduced by the aluminum in the molten steel. The reaction could occur within nine minutes.IntroductionNon-metallic inclusions would have positive or negative effect on steel quality depend on the quantity, size and composition of inclusions. Large inclusions are always detrimental. From the point of view of inclusion property, plastic inclusions are required by steel cord, while hard inclusions are preferred by pipeline steel. One of the most important ways to increase the steel quality is reducing the inclusion size and controlling the inclusion composition in steel. Nowadays, MgO based refractory is used as ladle glaze material with more and more frequency, which results in different inclusion characteristics in molten steel, for example, the inevitable generation of MgO contained inclusions during ladle treatment of steel. In other words, the inclusions in this type ladle will influence on the steel cleanliness and the product property. Thus, keeping an eye on the inclusion formation behavior in the steel with MgO-C ladle glaze is important for the steel industry. There have been a few studies in this regard. Li et al[l] studied the reactions between MgO-C refractory, molten slag and metal using a high temperature X-ray radiographic apparatus. They found that the local corrosion was regarded as due to the cyclic dissolution of MgO and graphite in the refractory into slag and metal phase. The gas bubbles formed according to the reaction of (FeO)+C(s)=Fe(l)+CO(g) greatly influenced the corrosion. On an industrial scale, Du[2] found that ladle glaze is a major source of inclusions in the ladle. An experimental study has been performed by Lehmann in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel[3]."

Jan 1, 2014

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By R. W. McCallum, B. Jensen, K. W. Dennis

"There are substantial challenges in the exploration of magnetic materials in the R-TM-X system (R =rare earth, TM= transition metal, X =stabilizing element) where Xis an element which has high vapor pressure, high reactivity, toxicity, or a refractory nature. This research focuses on discovering new phases with high anisotropy and high magnetization through closed diffusion couples inside high purity Fe crucibles. Either vapor-solid reactions or powder metallurgy techniques are then employed to isolate a stoichiometric sample based on a potentially magnetic phase found in the diffusion couple. For this research, X = F, Ca, Sr, Se, Zn, Bi or Cd, TM= Fe, and R = Nd. New ternary phases have been discovered with WDS and EDS, and magnetic transition temperatures have been measured with a SQUID magnetometer and VSM.IntroductionSince the discovery of the RCo5 compounds in the 1960s, rare earth- transition metal (R-TM) magnets have been the main focus of permanent magnetic research over the last five decades. Iron-based magnetic materials were studied next in attempts to avoid the unstable price of cobalt as well as the high price of Sm, the top performer in the RCos and RzC011 series. This hunt eventually led to the discovery of Nd2Fe14B with a theoretical BHmax of 64 MGOe, nearly double that of the previous samarium based magnets. The next few decades were devoted to enhancing the magnetic properties ofNd2Fe14B by the improvement of processing techniques and the additions of alloying elements. The only complete elemental substitution discovered in this system was R1Fe14C, which did not improve magnetic properties. It is probably safe to say that most ternary R-TM-X systems, where Xis any element that may stabilize a ternary phase, have been investigated if they may be prepared by conventional processes such as arc or induction melting. The present study offers a systematic approach to developing a novel diffusion couple technique in which the volatile, reactive or toxic alloying elements are laser welded inside a high purity Fe crucible. This experimental setup will prevent the oxidation of the rare earth element, as well as contain the volatile X element. As the goal of the research was to find new rare earth permanent magnets, only phases which contained greater than 60 wt% Fe were investigated. 247"

Jan 1, 2012

By Yi Tan, Kazuki Morita, Yaqiong Li

Molten Si-Al alloy, with the addition of Sn, was used for metallurgical grade Si purification by a low-temperature solidification method, with the aim of improving the recovery rate of Si. In this ternary melt, bulk Si was grown with a planar front by a directional solidification process under a well-controlled thermal gradient and growth rate conditions, thereby reducing the contamination of solvent metals. Effects of cooling rate, amount of Sn addition, and temperature gradient on the quality of bulk Si were determined. The criterion for constitutional supercooling for single-phase growth from multicomponent melts was employed to evaluate the growth process.

Jan 1, 2015

By G. Gerbeth, Y. Gelfgat, A. Cramer, A. Bojarevics

The production of highly porous metallic substrates requires an effective and well controlled production of metallic fibres with diameters in the range of 50 to 200 microns. The melt extraction, where a quickly rotating wheel extracts fibres directly out of the inductively heated melt, is a promising technology for that purpose. The main limitations of this process are due to turbulence within the melt and a wavy motion on the surface. Both effects give rise to strong and time dependent deformation of the melt surface which, in turn, causes non-stationary conditions of the contact zone between the extraction wheel and the melt. In the patent literature many examples can be found which try to overcome these problems by submersing mechanical parts directly into, or placing them at least in close vicinity to the melt, aiming at a stabilisation of that contact region. Even made of heat resistant ceramics they suffer from corrosion or cracks and do not work reliable at all. The present work describes a non invasive control mechanism by means of a magnetic field. Model experiments were carried out to study the calm down of the turbulent surface of a inductively stirred melt. The stabilisation of the melt surface has been demonstrated in practise by the installation of a solenoid at a working extraction facility under rough industrial conditions like a powerful induction heating and vacuum.

Jan 1, 1999

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated' cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By Edilson Marques Magalhães, Danielly Da Silva Quaresma, José Antônio da Silva Souza, João Nazareno Nonato Quaresma, Emanuel Negrão Macêdo

"The production of alumina from bauxite using the Bayer process generates the residue known by red mud. This material can be used as a source for concentration and recovery of valuable metals such as titanium. The greatest difficulty of concentrating titanium compounds is the large amount of iron oxide present in red mud > 30% by weight. This paper shows the extraction of the iron oxide, increasing the concentration of the titanium compounds. The red mud is leached with H2SO4 at 30% concentration and temperature range of 60°C, 80°C and 90°C. Analysis of the leached and concentrated was made to verify the effectiveness of the iron oxide extracting process and the titanium compounds concentration viability.2- IntroductionIn the state of Para is located the Industrial Unit Alumina of North of the Brazil S/A (Alunorte), created to produce and commercialize alumina, aluminum oxide, Al2O3. The ALUNORTE with Aluminum Brasileiro S/A (Albras) and Mining Rio do Norte S/A (MRN) complete the production cycle of aluminum in the state. Although the production of alumina has a importance great for the socio-economic status, as in any area other, generates a amount large of waste, thus causing environmental impacts. Pará State has produced 25 million tons of bauxite (Pinto, 2010), of which 60% were transformed into alumina plant in Pará and Maranhão by ALUNORTE by ALCOA, generating approximately 9,000,000 tons of waste known as Red Mud (RM). Due to the high reactivity this material is considered dangerous, and currently there is no operating process capable of reuse all the material produced at any refinery. The search for industrial processes in order to reuse these wastes can contribute to reducing the overall impact of the production process of alumina. In this context, this paper estudied, within the research line of Solid Waste valorization the mining industry and metallurgy, a process that makes possible the red mud as a source of raw material, in other words, seeks to maximize the use of red mud as raw material for concentration and or recovery of titanium compounds in both the crystalline form of anatase, rutile and ilmenite, avoiding the predatory extraction of natural resources of these materials. Applying definitely the concept of self-sustainability of the mining industry and metallurgy."

Jan 1, 2012

By J. C. Agarwal

Do large-scale projects in mining and smelting start up and achieve expected capacity on schedule? In most cases not. Regardless of worldwide location, company know-how, or financial backing, unforeseen delays occur. A comprehensive CRA study for the World Bank shows that delays are the rule, not the exception, in most mining and smelting projects. When delays are not factored into analysis and planning, financial projections are, literally, not to be believed. Returns on investment will seldom achieve their targeted level because of startup delays. This paper reviews the results of our analysis of startup of new mines, mills, and smelters; provides a detailed discussion of why delays occur in the smelters and refineries; presents the cash flow implications of startup delays; and discusses preventive measures that should be taken to avoid financial shortfalls,

Jan 1, 1983

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

By B. M. Fisher

A process for making electrolytic copper of high quality from copper flotation concentrates is described. The concentrates are first slurried and then subjected to a high-temperature, high-pressure, oxidation-leaching operation under controlled conditions. The resulting slurry from the oxidation-leaching operation is cooled or flashed to atmospheric pressure and then subjected to a solids-liquid separation. The separated liquor, containing the recovered copper values, is cooled and then fed to an electrolytic deposition operation where metallic copper cathodes of high purity are produced. The spent electrolyte is then subjected to a sulfide treatment to precipitate the residual amounts of copper not deposited in the electrolytic cells. The precipitated copper sulfide is recovered and recycled in the form of a slurry to the initial stages of the process.

Jan 1, 1976

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By Adolfo Pillihuaman Zambrano

Fe-Cr-C production is a very high electrical energy consuming process. Decrease up to 10% of this electrical energy is expected when self-reducing agglomerates are used. This research aims to understand how the synergetic effects are when stronger reductant, like Fe-Si, is substituted for coke in self reducing pellets. Brazilian chromites containing 41.2%Cr2O3 were mixed with petroleum coke and agglomerated with cement as the binder. Small amounts of 1%, 2% and 4% of Fe-75%Si were substituted for the equivalent petroleum coke, and pure silica plus hydrated lime were added for adjusting the slag composition. The mixture was pelletized, dried and submitted at 1773K up to complete the reactions. The results showed that the reduction reactions were 1.4 and 2 times faster with 1% and 2%Fe-Si addition, respectively, than with no addition. The microscopic analysis showed that it was formed a liquid phase, but the pellet did not collapse what indicates that the coalescence of the metallic phase depends on the dissolution of the pre-reduced particles of the chromites into slag.

Jan 1, 2008

By Zhi-xiang Cui

Dongying Fangyuan Nonferrous Metals Co., Ltd. has developed a new technology to produce anode copper from concentrates through only two furnaces. This new technology is called the Two-Step Copper Smelting Process. This paper presents the commercial application of the Two-Step Copper Smelting Process and its operating conditions. The key features of the Fangyuan Two-Step Process are as follows: (1) feed materials, including concentrates and flux, are mixed without pretreatment and fed into the Submerged Lance Smelting (SLS) furnace; (2) high grade white metal (WM) produced by the SLS furnace is transferred via WM conduit into one of the two Submerged Lance Converting and Refining (SLCR) furnaces; and (3) the two SLCR furnaces blow alternatively to maintain continuous operation of the whole production chain. The new smelter started operation in October 2015 with a processing design capacity of 1.75 Mt/year of mixed feed and has been operating for over 30 months.

By N. Kanari

The kinetics of oxychlorination of MgO by Cl2+O2 was studied in the temperature range of 850 °C - 1025 °C, using thermogravimetric analysis. The effects of C12/02 ratio, gas velocity, temperature and partial pressure of reactive gases on the reaction rate were investigated. The oxychlorination process was characterized by an apparent activation energy of about 214 kJ/mol. The reaction orders with respect to C12+O2. C12 and O2 at 950 °C were about 0.65.0.98, and -0.37, respectively. Some data about oxychlorination kinetics of MgO, Cr2O3, and MgCr2O4 contained in chromite were compared. Efficiency of using oxychlorination for the removal of iron oxides contained in magnesia was demonstrated.

Jan 1, 1999

Al2O3,-WC Composite powder for cutting tools was synthesized by self-propagating high-temperature synthesis using A1 powder as a reducing agent. WC, W2C and Al2O3 were concurrently formed in WO3Al-C system. It was found that the complete reaction was achieved with excessive addition of carbon and appropriate processing parameters such as degree of dilution, particle size of aluminum, compaction pressures of green pellets and carbon source. The final product which was leached by 50% HN03+HF diluted solution was consisted of Al2O3-55wt% WC having 2-3um of mean particle size.

Jan 1, 1999