Search Documents

By R. G. Reddy

Nickel solubilities in spent pickling solutions (i.e. HF-HNO3-H2O solutions ) were measured as a function of HF and HNO3 acid concentrations. The chemical analysis of the industrial pickling solutions and sludges were made. The stable phases observed in the sludges are FeF3?3H2O, and ( FeCr ) F3?3H2O. Pure Ni, and stainless steel type 316 were used in this study. The results showed that the solubility of Ni increased with increase in concentrations of HF in pickling solution at a fixed concentration of HNO3: An excellent agreement between the experimental solubility data and the theoretical data was obtained. X-ray diffraction analysis showed that the solid solubility product formed is mainly NiF2?4H2O compound.

Jan 1, 1992

By F. H. (Sam) Froes, C. Suryanarayana, K. C. Russell, C. M. Ward-Close

"Far from equilibrium synthesis allows development of novel crystal structures and microstructures, leading to achievement of enhanced physical and mechanical properties. A number of ""far from equilibrium"" techniques are reviewed with emphasis on the amount of departure from equilibrium. The ability of two such techniques, mechanical alloying (MAl, and physical vapor deposition (PVD) to develop novel structures are discussed in detail. For the MA process emphasis is placed on intermetallic compound compositions. Solubility extension, beyond rapid solidification (RS) levels, is found in terminal compositions but not for the intermetallics. Nanostructure-sized grains (< 100nm) form which can be retained after ""low temperature"" compaction. On continued milling in many cases the nanometer-sized grains transform to an amorphous structure. Ordering is destroyed by MA, except in those intermetallics with large negative enthalpies of formation. For the PVD process, a review of application to terminal light alloy compositions is presented. This includes a new high-temperature aluminum alloy, layered materials with nanometer spacing, corrosion-resistant magnesium alloys and low-density titanium compositions. IntroductionTo enhance the mechanical property combinations of advanced structural materials innovations in process/synthesis are required [1-6]. In this paper the capability of various ""far from equilibrium"" synthesis techniques [7,8] to produce novel constitutional and microstructural effects, and hence potentially enhanced physical and mechanical properties, in advanced materials is presented. The application of two such methods, mechanical alloying (MA) and physical vapor deposition (PVD) is discussed in detail. For the MA process emphasis is on intermetallic compositions with consideration given to solid solubility extension, microstructural refinement, amorphization, and formation of intermetallic compounds. For the PVD process application to terminal light alloy compositions is discussed."

Jan 1, 1994

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By Suchun Zhang

The alkaline oxidation of refractory gold concentrates containing arsenopyrite and pyrite at ambient temperatures and pressures has been found to be accompanied by the simultaneous dissolution of gold without the addition of cyanide. A detailed study has been made of the kinetics of the oxidation of the pure minerals and of several concentrates. The reaction products of the oxidation of arsenic and sulphur have been monitored using chromatographic techniques. In the case of arsenopyrite, thiosulfate, monothioarsenate, arsenate and sulfite are the principal products while thiosulfate has been confirmed to be the dominant product of pyrite oxidation. Gold, either as added powder or as a constituent of the concentrates has been found to dissolve simultaneously during the alkaline oxidation of both arsenopyrite and pyrite, and this appears to be associated with the in-situ formation of thiosulfate as a lixiviant. The effects of temperature, stirring speed, oxygen partial pressure, alkalinity and pulp density on the oxidation of arsenopyrite and the dissolution of gold have also been investigated. Keywords: Gold, dissolution, arsenopyrite, pyrite, alkaline, oxidation, thiosulfate, thioarsenate

Jan 1, 2005

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998

By Xin Li, Hai-Xing Fang, Bing Xie, Hong-Yi Li

Chromium-containing vanadium slag (V-Cr slag) was obtained by an industrial smelting process of Hongge Ore, which is valuable vanadium-titanium magnetite to extract V and Cr in China. Sodium roasting thermodynamics of V-Cr slag in presence of oxygen were calculated to evaluate the reactivity of chemical compounds. Results showed that the oxidation of FeV2O4 was intensified in presence of Na2CO3 while the oxidation tendency of FeCr2O4 was far lower than that of FeV2O4. It was probably that reactions of impurities including Al2O3, SiO2 and Fe2O3 with Na2CO3 happened and the products can promote the oxidation of vanadium or chromium compounds in lower valence. Based on thermodynamic analysis, a two-step selective extraction process of vanadium and chromium was proposed. Extraction rate of vanadium was 88.6% while 7.0% for chromium in the first extraction step; extraction rate of 90.7% and 95.4% for vanadium and chromium, respectively, were obtained in the second step.

Jan 1, 2014

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By Kenneth N. Han

Thermodynamic and kinetic aspects of nickel and cobalt leaching from metals. minerals and ores in various media have been reviewed and discussed in this paper. A kinetic model developed to delineate the leaching mechanisms for these metals has been discussed in view of experimental observations. The current review also includes the dissolution behavior of nickel and cobalt from various minerals such as oxides, sulrides. ocean floor manganese nodules, and laterites. A particular emphasis has been extended to similarities and differences of the dissolution behavior of these two metals in various media. The leaching of nickel as well as cobalt metal in acidic solutions and arnmoniacal solutions exhibits in most part mass transfer controlling. although at some pH&apos;s, chemical controlling or mixed controlling mechanisms seem to prevail. The leaching of nickel and cobalt from oxides in acids and ammoniacal solutions. on the other hand, can be described best by chemical controlling mechanisms.

Jan 1, 1993

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By R. Boom, B. Kraaijveld, H. Kuntzel, Y. Meteleva-Fischer

"Alloying refining with rare earth elements followed by acid leaching was examined for the potential of upgrading of metallurgical grade silicon. Microstructure study of silicon alloyed with small additions of rare earths showed behavior relatively similar to the influence of calcium addition. After alloying with neodymium the phosphorus content was detected in various intermetallic silicides containing neodymium and iron. The content of lanthanum and neodymium in refined silicon was by several times lower than that of aluminium and calcium. Alloying with lanthanum and neodymium at smaller additions than calcium reduced the phosphorus content down to the same level. The efficiency of lanthanum and neodymium in removal of boron and phosphorus at the 1-2 wt% of their additions and their low solubility in silicon make the alloying with these metals followed by acid leaching an attractive option for the refining route of metallurgical grade silicon up to solar grade.IntroductionA striving for a cheap ""green"" energy directs the research interests in silicon solar cells towards new efficient refining routes for metallurgical grade silicon (MG-Si, -98% purity). The silicon price determines up to high extent the solar module's price, so that cheap and efficient metallurgical process is awaited. The research challenge is to fulfil the purity requirements of solar grade silicon (SoG-Si, 6N) by competing with the energy-consuming and environmentally unfriendly Siemens process. Most difficult impurities to remove are boron and phosphorus, so technologies dedicated to their efficient removal attract an attention of industry and academia.Alloying refining (also known as solvent refining) is one of the most promising refining options, which is based on a principle of solid-liquid extraction using limited solubility of impurity elements in solid silicon [ 1]. Various elements were proposed for alloying refining: aluminium [2], calcium [3], tin [4], iron [5], copper [6] etc. The attractiveness of the alloying refining is in decreasing a melting point of the metal mixture and an affinity of the alloying element to the most harmful impurities, especially to boron and phosphorus. However, the difficulties are still faced due to self-solubility of the alloying elements, their low affinity to boron and/or phosphorus, silicon losses and necessity of removal of the silicide impurity phases in an additional step, using acid leaching [7], fractional melting [ 8] etc."

Jan 1, 2013

By I. D. Reznik

On blowing nickel matte in a converter without quartz, first the oxidation of metallic iron and a part of FeS occurs without evolving sulfur dioxide, the formed FeO dissolves in a sulphide smelt and form a homogeneous oxysulphide smelt. On further increasing the FeO content, the oxysulphide separates into 2 layers. Based on the laboratory investigation of FeO-(FeS+Fe°) - (Ni3S2+Ni°) ternary phase diagram we have identified the separation region at 1250°C. The boundaries of the separation region have the form of an arc and the composition of the separated oxysulphide layers is defined by the canodes. In the nickel or copper-nickel matte - silicacalcium oxide slag system at 1250°C three layers, namely sulphide, oxysulphide, and slag may be formed. A high slag basicity due to the presence of CaO can serve to enhance the activity of FeO; a low nickel content in the matte corresponds to a high concentration of FeS therein; FeO from slag and FeS from the matte form a homogeneous FeO-FeS solution, i.e. an oxysulphide layer. The investigation on the "Camebaks" apparatus and by the nuclear gamma-ray resonance spectroscopy method of the phase composition in a slowly cooled oxysulphide layer has shown the presence of four phases: wustite, troilite, ferronickel grains, and calcium oxide-silica inclusions. Knowledge of regularities in the oxysulphides formation makes it possible to use them in pyrometallurgy of nickel and cobalt or preventing their formation.

Jan 1, 1997

By T. E. Warner

In order to detect arsenic and antimony in zinc, various electrochemcial experiments were performed involving the electrochemical introduction of sodium atoms into molten zinc using a solid electrolyte. Under high rates, the formation of the intermetallic phase NaZn13 was assumed to form. Under more moderate injection rates of sodium, employing a symmetric "zinc/zinc cell", a qualitative relationship between the current generated during cyclic voltammeuy and the arsenic and antimony concentrations in molten zinc was observed.

Jan 1, 1999

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By William Petruk

An investigation was conducted to determine whether mineral liberation data obtained by one image analysis technique are the same as data obtained by another image analysis technique. The liberated vs non-liberated, volume % and weight % techniques for measuring mineral liberations by image analysis were tested. The results show significant differences between the values obtained by the different techniques. The lowest liberation values were obtained by the liberated vs non-liberated technique and highest by the weight % technique. It is interpreted that the weight % technique produces the most realistic results. The weight % technique also produces data that can define mineral associations for the unliberated grains. These include (1) mineral quantities in particles that contain different amounts of unliberated mineral, (2) mineral quantities in particles that have different size ranges, and (3) mineral quantities and degrees of liberation for specific minerals in particles of different size ranges.

Jan 1, 1996

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By KNona C. Liddell

The ion interaction model Pitzer proposed twenty years ago is today the most widely used method for calculation of osmotic coefficients and electrolyte and single ion activity coefficients in aqueous solutions. This is due in part to the accuracy of the results that have been obtained for many concentrated electrolytes. An additional factor is that, compared to alternative activity coefficient models, there are many more parameter values available for the Pitzer equations. The important features of this model are reviewed. Published parameter values for Co, Ni, Cu, Zn and Fe are tabulated, and applications of interest in the aqueous processing of these metals are described.

Jan 1, 1993

By Y. W. Chung, W. I. Chia

"The interaction of water vapor with single crystal Ni3(Al,Ti) and polycrystalline Ni3Fe, with and without the presence of oxygen, has been studied with Auger electron spectroscopy, photoemission spectroscopy, thermal desorption and isotope exchange. Water dissociates to produce atomic hydrogen above 200 K on both Ni3(Al,Ti) and Ni3Fe surfaces. For Ni3(Al, Ti), the reaction is structure-sensitive. Pre-adsorbed or co-adsorbed oxygen on Ni3(Al,Ti) and Ni3Fe significantly suppresses hydrogen production due to water dissociation. This suppression process occurs more efficiently on Ni3Fe than Ni3(Al, Ti).IntroductionOrdered intermetallic compounds such as aluminides, silicides and titanides are very attractive for structural applications at high temperatures. This is because these intermetallics tend to form adherent oxides in oxidizing environments which protect the base materials from excessive oxidation and corrosion. In addition, they have low density, relatively high melting points and good high-temperature strength. However, the moisture in air severely embrittles many ordered intermetallics such as FeAl [1-3], Fe3A1 [4,5], C03Ti [6,7], (Co,Fe)) V [8], Ni3Si [9], Ni3(Si,Ti) [10], Ni3(AI,Mn) [Ill, and Ni3A1 [12-14], resulting in low 'ductility and brittle fracture at room temperature. Recent studies by Liu and coworkers (see review by George and Liu [15]) provide a qualitative description of the mechanism for this moisture-induced embrittlement. During elongation testing, cracks are formed, thus exposing fresh alloy surfaces. One or more active components of the alloy react with water vapor in the environment to produce atomic hydrogen which penetrates into crack tips and causes hydrogen embrittlement. This is similar to that proposed for moisture-induced embrittlement of aluminum alloys [16]."

Jan 1, 1996

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By J. J. Moore

The application of plasma technology to process metallurgy is briefly discussed. Experiments involving in-flight reduction of minerals (taconite, chromite, in particular) with a solid-based carbon reductant are described. The resultant metallic and slag product analysis is discussed with respect to thermodynamic and kinetic considerations.

Jan 1, 1985

By Norbert L. Piret

From the copper smelter operation a various outputs are to exert negative impacts on the environment. Particularly, emissions like SO2 and dusts, solid wastes like contaminated gypsum and arsenic sludge, effluents and heated cooling water are generated. Most countries have sitipulated an environmental legislation to provide the framework for an efficient environmental management. As part of the planning activities for x major greenfield copper smelter, the Following elaborations are required and were drawn up. -The Environmental Impact Assessment which is the first step of environmental management and mandatory for every new project. - The Environmental Monitoring Plan, which describes the monitoring procedures for the main impacts identified and assessed. -The Environmental Management Plan, which deals with the minimization of environmental impacts, and the methods of its implementation.

Jan 1, 1996