Search Documents

By E. De Souza

Rockbursts and rockfalls cause very large safety and productivity losses in underground mines. One of the major unsolved problems of safe, economical rock support in underground mining has been that of maintaining anchorage during dynamic rock loading conditions or seismic related occurrences. It is recognized that the large displacements and high strain rates in excavation walls and underground structures cannot be countered by increasing the strength of stiff rock-reinforcing systems but must be accommodated by introducing yieldability into the support elements. This paper introduces a low cost yieldable support system which provides viable solutions to dynamic support loading. Such system should not only provide a feasible and more effective rock mass stabilization strategy but improve mine safety and reduce losses.

Jan 1, 1998

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987

By J. A. Madonna

Universities and colleges in three countries, Australia, Canada and the United States, recognized the need to establish and/or reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral industry organizations cooperated in the study by providing information regarding their specific training needs for support personnel. The data gathered has been used to identify training areas for semi-skilled, skilled and technical personnel in geochemical mineral exploration, including, but not limited to, geological skills, geochemical skills, environmental skills and computer skills. With the areas of major educational need defined for geochemical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will be discussed.

Jan 1, 1993

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By John C. Bowling

Many recent mine developments in North America are located in remote northern regions with extreme winter temperatures in the range of -20oF to -60°F. In addition, many locations are subject to very heavy snowfall. This paper discusses some of the key considerations in the planning and design of mine plant buildings, particularly concentrators, located in these regions. SUMMARY & CONCLUSIONS The subject is considered under three main headings: I. Building Out line and Structural Frame 2. Wall and Roof Materials 3. Foundations The plan outline of a mine plant building will naturally be governed by the scope and layout of the process equipment it contains. The selection of roof profile, on the other hand, will generally depend upon a number of factors extraneous to the process e.g. snow conditions. When these factors are considered for concentrators in cold locations, a flat or stepped roof will usually be more economical and suitable than a sloping roof. The materials normally used for the structural framework of concentrators are the same as used for other industrial buildings, namely steel, concrete and wood. Structural steel, however, is the most commonly used material for concentrators in

Jan 1, 1971

By E. H. Christiansen

Gem-quality red beryl in the Wah Wah Mountains of southwestern Utah formed as a post-magmatic mineral in a topaz rhyolite flow. Unlike topaz, this beryl occurs along fractures in devitrified rhyolite, rather than in lithophysal vugs. The flow occupies a graben and perhaps a significant paleo-drainage. Beryl occurs at medial depths within the eroded flow, about 170 m below overlying mafic lava flows. Both beryl-bearing fractures and the host rhyolite show an unusual amount of argillic alteration compared with other topaz rhyolite flows. Alteration may be related to the incursion of surface water along shrinkage fractures within the flow. Whole-rock concentrations of CaO within the host rhyolite are very low (<0.01 % to 0.18%) compared with other topaz rhyolites and Be concentrations (about 20 ppm) are about average. Low Ca activities prevented fluorite precipitation and allowed Be transport as fluoride complexes. Beryl probably grew at subsolidus temperatures (-300-650°C), but above the temperature of kaolin development (200-300°C) as fluoride-rich vapors, released by devitrification, encountered fractures and mixed with vapors derived from surface water flowing through the fractures. Beryllium fluoride complexes reacted with water vapor, silica minerals, alkali feldspar, water, and Fe-Mn oxides along fractures to produce red beryl. Continued reaction of the cooling flow with surface water at lower temperatures probably produced a boiling, more acidic fluid that produced the argillic alteration. Consequently, eruption of low-Ca topaz rhyolite followed by entrance of surface water into medial portions of a devitrifying and still hot lava flow appear to be critical factors that led to red beryl formation.

Jan 1, 1996

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By R. L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps is a potentially hazardous practice which often results in localized slope failures. A limit plasticity approach to determine the total admissible weight for moving loads near slope crests is presented. A three-dimensional analysis provides an upper bound solution to the load that can be applied to the top of the slope (dump point), and it also provides the critical distances of the load from the slope crests. The analysis accounts for the inertial forces generated by the deceleration of a moving load (e.g., a dump truck), and it also includes the drag resistance of the front wheels if the brakes are engaged. The results can be utilized to determine the safe operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism. An example with realistic parameters also will be presented.

Jan 1, 1991

By Emanuele Catelli, Paolo Vicentini, Manuel Petitat, Paolo Lanfranchi

"More than 800 million tons of material will be excavated during large underground projects such as tunnels, undergrounds and power plants by 2030 in Europe only. The raw material excavated is often classified as waste, which involves environmental impact and transport issues: landfill areas, CO2 emissions and noise. But how can such massive amounts of material be transported, processed and deposited? Using the example of the AlpTransit Ceneri Base Tunnel (15.4 km), we show that suitable excavated materials can be used sustainably as a primary resource for tunnel concrete. This requires careful planning of the installations and storage areas by the client, timely building of the processing plants and other handling facilities outside the tunnel and a continuous evaluation of the raw material quality. 1. INTRODUCTION Spoil management is a central element of large construction projects. The systematic reuse of suitable excavated material not only saves natural resources, reduces transport distances and landfill volume, but can also decrease overall construction costs. Ideally, all of the concrete needed for tunnel lining can be produced with this on-site material. Such a natural resource management concept was applied for the construction of the new Gotthard Base Tunnel (L = 57 km). Spoil management concepts are, how-ever, difficult to implement and call for innovative techniques, sophisticated logistics and organization. In the context of large projects, environmentally friendly transport, processing and storage of millions of tons of excavated loose material represent another logistics challenge (Simmen & Lieb, 2010). This paper shows key factors that led to the successful completion of spoil management at the Ceneri Base Tunnel, which constitutes a part of the AlpTransit Gotthard Project (Figure 1)."

Jan 1, 2016

Power consumption of stirred media mills has been studied by an approach developed from work on stirred reactors. Relationships between torque required to rotate both disc and pin impellers immersed in dense particulate media as a function of speed, impeller and tank dimensions, and other relevant variables are evaluated. Data collected during numerous different experimental conditions are analyzed. The results can be summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention is directed towards the rheological properties of the media, which is considered as non-Newtonian liquids and hence, the equation of power law liquids is employed. Procedure for estimating parameters of effective viscosity and scale-up guidelines with respect to power consumption are put forward.

Jan 1, 1994

By Paul Soros

The rationale for innovations in two directions is identified: raising capital and annual throughput, in order to avoid the cost of constructing and operating an additional system and to reduce the capital cost of pits and tunnels, applicable to installations of any capacity. Cast histories cover railroad unloading of bottom dump cars, rotary dumping of random cars, with and without indexer, and unit trains as well as truck unloading of multiple grades of coal.

Jan 1, 1985

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains (CAC) on roof bolting machines have been proven, through laboratory and field investigations, to protect miners from respirable dust, preventing dust overexposures. Another desired application is to develop a CAC that is mounted in the compartment of a shuttle car to protect the operator from dust. The challenges faced with this design include mine ventilation rates in tandem with the shuttle car tram speeds, causing cab airspeeds that may exceed 600 fpm, as found in this study of a central Appalachian underground coal mine. Prior research and laboratory testing indicate that successfully protecting a miner in high air velocities is difficult to achieve because the clean air from the CAC is unable to penetrate through the high velocity mine air and make it to the breathing zone of the operator. During this investigation by researchers from the National Institute for Occupational Safety and Health (NIOSH), dust concentrations of the shuttle car operator were measured. Also, air velocities experienced by the operator were measured using a recording vane anemometer. Results from the survey indicate that the highest exposure to respirable dust (2.22 mg/m3) occurred when the shuttle car was loading at the continuous miner, where there was an average airspeed of 157 fpm. While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 203 fpm. This study indicates that a CAC system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, since the majority of the operator’s dust exposure occurs in air velocities less than 200 fpm. INTRODUCTION NIOSH has issued a contract (#200-2015-63485) with Marshall University and J.H. Fletcher & Co. (Salem et al., 2016) to develop a canopy air curtain (CAC) for coal mine shuttle cars. The proposed design maintains a similar design to the roof bolter CAC by providing filtered air via a blower over the operator. The plenum, which will provide the uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a CAC is ventilation airflow perpendicular to the plenum airflow [Engel et al. 1987]. This ventilation airflow, if the velocity is significantly high, can shear the downward flow from the plenum. The shear caused by the ventilating airflow can reduce the effectiveness of the CAC by either disrupting the downward flow or allowing contaminated mine air into the CAC zone of protection."

Jan 1, 2018

By B. K. Gupta

Arch Mineral&apos;s Captain Mine has used the Bucket Wheel Excavator System(BWE) for over 3 years in conjunction with a 180 yd3 (138M3) stripping shovel. The bucket wheels prestrip the soft overburden ahead of the shovel. This soft overburden is brought to the spoil side through a series of shiftable conveyors and placed by a spreader over the ungraded or partially graded shovel spoils. The placement of the soft overburden and top soil is accomplished in a manner that meets the reclamation mandates. The prestripping by the BWE has reduced the incidence of the highwall and spoil slides, depth the stripping shovel has to dig and the volume handled by the pullback draglines.

Jan 1, 1984

By D. Goffaux

In less than two years, Stratmin has discovered, explored, developed, financed and put into production by open pit, a large graphite mine. The deposit, hinted by airborne electromagnetic survey, was discovered in September 1987 through various ground geophysical surveys, diamond drilling and trenching. The open pit started production in February 1989, feeding a nearby leased mill at Notre-Dame-du-Laus (Quebec), having a processing capacity of 400 tons per day. A new 1,000 tonne per day mill was built at the mine site, in Lac-des-lies (Quebec) and began production in April 1990. The Lac-des-lies graphite operation is currently one of the largest of its kind in the world. Mine and mill facilities are operated by Stratmin Graphite, jointly owned by Stratmin Inc. (75%) and Imetal-France (25%), a wholly owned subsidiary of Imetal (France). From initial exports limited to Japan and United States, Stratmin Graphite is now exporting in fourteen different countries, attesting to the very high quality of its products, with grades ranging from 92% to 97% carbon. Among the numerous graphite deposits discovered in Canada, Stratmin Graphite Inc. has emerged as the leader and virtually the sole crystalline graphite producer in North America, operating on a continuous basis.

Jan 1, 1992

By Mike Hall, Tim Kelly, Mohammad Reza Jafari, Ulf Georg Gwildis

"Qatar’s capital Doha is undergoing major infrastructure improvements including a multiphase stormwater management program. Although located in an arid climate, Doha experiences flooding during rainfall events. Dewatering operations and rising groundwater levels add to the management needs. To address those needs, construction of the Musaimeer collection tunnel along Doha’s southern rim is being followed by a marine outfall tunnel connecting a pump station to a dispersion field 10 km offshore. Qatar’s geology is characterized by sabkha deposits, a series of predominantly weak and karstic rock strata that creates challenging conditions for mechanized tunneling, as highlighted by the uncontrolled flooding of a tunnel boring machine (TBM) used on the Doha Metro tunnels. Risk associated with these challenges is magnified for the outfall tunnel by drive length, sub-sea elevation, and a single access point. This paper describes the outfall exploration strategy and design decisions made in light of experience gained during the collection tunnel construction. CONTEXT – STORMWATER MANAGEMENT PROGRAM Qatar has an arid climate with an average annual precipitation of less than 100 mm. Precipitation is mostly confined to the winter months when rare, but occasionally heavy rainfall events easily lead to flooding in Doha’s metropolitan area. Its coastal location and flat topography a few meters above the sea level mean that the depth to the groundwater table is generally shallow. The karstic aquifers in the regional dolomite and limestone series contain groundwater of high salinity, which is not suitable as a potable water source. For supplying Doha’s population of more than 900,000 (2014) with potable water, the Ras Abu Fontas seawater desalination plant is operated about 10 km south of the city. This potable water production capacity is crucial for Doha’s development and – in conjunction with overirrigation and leaking sewage tanks – is also the root cause for rising groundwater tables that have been observed over the past years."

Jan 1, 2016

By J. H. Desautels

The modern coal mining industry is subject to a vast array of regulations affecting virtually all aspects of its operations. Probably the most significant over-sight role involves the Office of Surface Mining Reclamation and Enforcement (OSH) established by the Surface Mining Control and Reclamation Act, or SHCRA.1 Although complying and coping with SHCRA can be difficult for coal operators, this complex regulatory process has helped insulate the industry from ongoing efforts to extend regulation under the Resource Conservation and Recovery Act, or RCRA, 2 to aspects of the mining industry in general. The Environ-mental Protection Agency (EPA) has struggled with regulation of mining wastes under RCRA since the mid-1970&apos;s, but RCRA itself places most coal mining wastes firmly under the control of OSH and SHCRA. Despite the general exemption from RCRA regulation for waste materials that result from extraction and processing of coal itself, there may be circumstances under which coal mining operators could find themselves subject to regulation under RCRA or a number of other statutes administered by EPA. This paper will review briefly the history of mine waste regulation under RCRA, as well as touch on the policy decisions that led to the exemptions from RCRA regulation. The paper will summarize coal waste requirements under SHCRA, and also will review what operations at coal mines need to be controlled, in order to avoid potential liability under RCRA. In addition, it will mention requirements under other federal laws, including CERCLA, or the "Superfund" law,3 and describe how they may impose restrictions or liability on coal operations for waste or other materials commonly found at surface and underground coal mines.

Jan 1, 1993

By O. A. Velasquez, A. R. Kumar

"Continuous miners are often equipped with a flooded-bed dust scrubber to clean the air from close to an active underground coal mining face. However, its impingement screen is prone to clogging due to an accumulation of dust, thereby lowering the scrubber’s efficiency and potentially exposing the mine workers to higher levels of dust. Fans can compensate for the increased resistance by varying their operating parameters, but the scrubber screen needs significant maintenance which leads to downtime. The authors have proposed a suitably sized Vortecone as an alternative to the conventional flooded-bed dust scrubber system. Water is used as the filter medium, which is replaced and recycled continuously. Preliminary CFD investigations of Vortecone scrubbers have indicated higher cleaning efficacies, especially in the respirable range. This paper presents the results including the flow characteristics and capture efficacies of a full-scale Vortecone. Multi-phase flows, including free-surface modeling and particle tracking methods, have been adopted. ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research project. This research is being developed with the support of a NIOSH Grant 200-2014-59922- ‘Coal Mine Dust Mitigation through Novel Scrubber Development and Numerical Modeling’. The views expressed in this paper are those of the authors and do not necessarily reflect those of NIOSH. This project is aimed at designing novel and efficient scrubbing systems for underground mining operations. The authors acknowledge Dr. Thomas Novak of the Department of Mining Engineering, the University of Kentucky for his support and encouragement. The authors also thank Dr. Sunil Vytala, CFD engineer at Cradle CFD for his invaluable inputs to the numerical models.INTRODUCTION Continuous miners are the main production machines deployed in room and pillar mining operations. These miners extract coal by the shearing action of the wethead cutting drums. Strategically placed water sprays on the drum not only cool the bits extending their useful service life, they also suppress the dust at the point of generation itself. A flooded-bed dust-scrubber (Campbell, et al. 1983) is usually integrated onto the continuous miner to arrest dust from close to the active face. These fan-powered scrubbers have an impingement screen flooded with water, which also serves as the filter element. A demister downstream of the screen removes the excess water from the air cleaned. These conventional scrubbers have been found to be very effective in alleviation of respirable dust levels underground (Chao and De-sheng 2000) (Colinet, Reed and Potts 2013). However, the inefficiencies of the flooded-bed dust scrubbers arise out of their internal components. Depending on the mining conditions, the screen may be clogged by the accumulation of the trapped dust particles. The resistance of the scrubber system is increased reducing the airflow. The flooded-bed dust-scrubber system would, therefore, require frequent maintenance of the screen and the demister (Listak 2010). Since any maintenance needs to be carried out under supported roof, this leads to loss of availability of the equipment as well. In addition to this, the continuous miner operators could be exposed to elevated levels of dust when satisfactory airflow at the face is not achieved."

Jan 1, 2018

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

By G. Buchan

This paper discusses the design of long panels for longwall mining at Twentymile Coal Company (TCC) from conception to implementation. The case study of the long panels at Twentymile includes extensive mine plan reengineering in the early 1990&apos;s to world record production months in 1996 and 1997. The obstacles of subsidence engineering, environmental regulations, conveyance, ventilation, equipment design, and continuous miner (CM) development timing had to be overcome to successfully begin longwall production within a 4 year time frame. The background and some detail for each of these areas listed will be discussed to show how the coordination of many facets must be pulled together to implement a successful long panel mine plan.

Jan 1, 1998