Search Documents

By Raphael Mourad, Colin R. Phillips

Investigation of the traps in LiF:Mg, a multi-peak phosphor, was carried out using simple phosphorescence decay analysis. Half lives at room temperature of the trapping centres (peaks -lb, -la, -1, 0, 1, 2, 3a and 3) in the phosphor after irradiation with [a] radiation were found to be 3 s, 5 s, 28 s, 4 min, 15 min, 1 h, 6 h and 2 d respectively. Justification for the method of analysis is pro- vided and the results of measurements compared with published data. The effects of pre-annealing at 400°C for 1 h and 80°C for 24 h on the trapping configuration and on the trapping efficiencies were also studied.

Jan 1, 1981

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By R. H. Seraphim

The name is derived from an Egyptian myth, "A beautiful lone bird which lived in the Arabian desert for 500 or 600 years and then consumed itself in fire, rising renewed from the ashes to start another long life." HISTORY This account of the first history is gleaned from old reports and documents which are listed in the Bibliography and from discussions with old-timers of the district. Prospectors were active in the vicinity of Greenwood in 189 1, and in that year staked the Mother Lode, Crown Silver, and Sunset. Henry White staked the Knob Hill claim in Phoenix on Jul. 15, 1891, and by the end of the year, other prospectors had staked most of the claims covering the valuable ore bodies in the camp. Much surface work done in the early years indicated that the values in copper, gold, and silver were low. Large capital investments were required to develop the ore bodies and build smelters. The discovery that the ore was practically self-fluxing greatly enhanced the value of the deposits. A map of the area showing the geology is given in Fig. 1. The bedded Brooklyn conglomerate is shown in Fig. 2.

Jan 1, 1991

By R. Bhaskar

Although the health effects of airborne dust in underground coal mines are well recognized, a lack of understanding remains about the fundamental mechanisms of dust generation, transportation, deposition and dust-lung reaction. This study was intended to contribute to the understanding of dust transportation and deposition mechanisms in underground mine airways. Data from in-mine experiments carried out under controlled conditions in a straight section of a longwall panel with three different airflow velocities and two different types of coal dust (bituminous and semi-anthracite) were used to determine the turbulent deposition rate of dust particles. Measurements of ambient dust concentrations and deposition along the mine airway were obtained and the total dust deposition velocity (rate) was calculated. The deposition velocity of turbulent diffusion was estimated based on the experimental data and theoretical equations. The effects of airflow velocity, particle size, particle density and distance from the dust source on gravitational, turbulent and total dust deposition are discussed along with related conclusions.

Jan 1, 1995

By Robert F. Conley

This paper describes attrition milling as exemplified in rotary and vibratory mills for ultrafine grin¬ding application Without attempting to narrate the differences between various devices, generalized differences between the broad categories of rotary and vibratory milling are presented and compared with the ball mill Applications of these mills for coal, limestone, kaolin, mica, talc and iron oxides are described giving specific differences of the mineral properties that affect their behavior in the grinding mills Where applicable, specific recommendations are provided for ultrafine grinding of various industrial minerals

Jan 1, 1983

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By J. Brent Hiskey, Srini Raghavan

The physical chemistry of dissolution of silicate and complex oxide ores in aqueous lixiviants has been reviewed. Particular attention has been paid to the analysis of dissolution mechanisms and kinetic models and to the elucidation of the role of the porous nature of the materials on dissolution behavior. Importance of the physico-chemical characteristics of the leach residues on leaching efficiency has been discussed.

Jan 1, 1989

By R. R. Tatiya

The algorithms to model three stoping methods - sublevel, down- the-hole (DTH) and cut and fill stoping have been developed. These algorithms are capable of designing and performing economic analysis for one or more number of stopes in a continuous orebody. The design and economic analysis of each individual stope are first obtained. This is followed by the composite stope design layout and overall economics of the stopes under study. This paper describes only the stope design aspects of these models. The programs have been written using Fortran 77 with Tektronix graphical aids available at Imperial College Computer Centre (ICCC) London and are based on the basic data obtained from Khetri Copper Complex (KCC) and Rajpura Dariba (a zinc mine) in India. Minor modifications, however, may be necessary in some routines when used on other systems and for other mines.

Jan 1, 1989

By S. K. Mishra, S. B. Kanungo, D. Biswal

An attempt was made to beneficiate low-grade, high-phosphorus manganese ores of the Garividi-Garbham region of Andhra Pradesh, India, by using wet high-intensity magnetic separation (WHIMS). The distribution behavior of both mass and chemical constituents in different size fractions of a typical highly weathered ore sample was studied to obtain information about the liberation characteristics of various chemical constituents. Magnetic separation indicated that in the +208-µm size fractions, P and acid insolubles were concentrated in the magnetic fractions. However, in the -208-µm size fractions, P and acid insolubles were concentrated in the nonmagnetic fraction because of a lower recovery of the magnetic fraction. Variations in field intensity between 1.3 and 1.75 T had little effect on the recovery and the grade of concentrate. The results also demonstrated that phosphorus was associated with all three major constituent phases, namely, oxides of Mn and Fe and aluminosilicate gangue minerals.

Jan 1, 2000

By G. T. Adel

This paper presents the highlights of a general-purpose simulator for mineral processing plants that is being developed at the University of California, Berkeley. The state-of-the-art structured design methodogy based on a top-down design approach is being used to construct a modular and completely structured simulator such that it is independent of the unit operation models and routines. The simulator provides for two levels of operation allowing prebuilt or user-built simulation flowsheets depending upon the degree of computer knowledge expected of the user. The philosophy used in designing this simulator appears to be unique in the field of flowsheet simulation. The paper also includes a mini-example demonstrating the usage of the simulator.

Jan 1, 1982

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high-expansion foam generator. Thus allows fire fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600 ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Jan 1, 1996

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By Xinming Lu

In this paper, we use a new kind of fan charateristic curve instead of the common quadratic function, and give the existence and the uniqueness of the solutions to the ventilation network controlling equations, so that the existence and the uniqueness of the solutions for the natural air distributting problem can be conveniently given. We also give a conjugate gradient method with the global convergence to solve the equations having the unique solution. Because we adopt a very efficient technique of one dimensional search (or linear search) in this method, the method can quickly solve a lot of problems, especially in large scale problems. The second part of this paper is the establishment of the model of the constrained quadratic programming for the measurement adjustment of mine ventilation network. We give the algorithm to solve this model as well. The two algorithms given above have been realized in the mic-computer MC-68000 with Fortran codes, and the numerical results are satisfactory.

Jan 1, 1991

By W. F. Hahnert, T. L. Ward, K. E. Stoll, P. A. S. Ralston

Fuzzy logic is well suited to the control of non-linear, time-varying, and/or any system for which it is difficult to obtain an exact mathematical model. To design a good fuzzy controller, a thorough understanding of the desired process behavior is required. Many papers have suggested that fuzzy controllers are robust. If they are, it is reasonable to explore whether or not they respond better than conventional controllers to errors in the feedback signal due to imperfect measurement or sensor degradation. It may be the case that simpler or less expensive sensors could be used in some processes. The research presented here relies on an integrated array of computer programs that model and simulate (1) the process to be controlled, (2) common feedback instrumentation, and (3) both fuzzy logic controllers (FLC's) and conventional controllers. Various types of feedback sensor imperfections are imposed upon the system, and the performance of the two controllers is compared. Each controller is tuned to its optimal performance in response to a setpoint change using perfect feedback measurement.

Jan 1, 1993

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By S. G. Malghan

This paper reviews uses of sodium sulfide in the flotation of oxide minerals of copper, lead, and zinc. The activation and depression effects of sodium sulfide are of particular importance because of their applications with oxidized lead and copper ores. In spite of its industrial importance, the nature of the heterogeneous reactions between sulfide ions in solution and the surface of oxidized minerals has not been fully understood. Hence, proposed mechanisms of the sulfide action in flotation, methods of measuring and monitoring sodium sulfide in flotation pulps, and variables influencing the sulfide addition are analyzed. Recent studies on sodium sulfide addition to flotation pulps, monitoring its concentration, and the optimum dosage control using platinum and/or sulfide specific ion electrodes are discussed.

Jan 1, 1987

By D. Koch

Bentonites and bentonite containing sealing materials are used since many years for sealing purposes in foundation, dike construction, hydraulic engineering and landfill construction, especially for encapsulation of old waste deposits In the near future compacted bentonites will be important components of multi-barrier systems for dry charge of old mines, for underground disposal of hazardous or radioactive wastes. Because of their exceptional physical, structural and chemical properties, bentonites are offering manifold possibilities to protect the environment against the negative effects of dumping grounds. Often the compliance with legal regulations for waste dumping or the isolation of contaminated areas is possible only by using bentonite containing sealing systems. The essential properties of bentonite, bentonite containing building materials and the different techniques of making horizontal technical base liners and vertical cut-off walls are explained. For horizontal technical base liners the adsorption ability, the ion exchange capacity and the swelling behavior of bentonites are important. For cut-off walls bentonite controls the rheological behavior of the slurry and is responsible for the low permeability of the hardened bentonite-cement-wall. In the multi-barrier systems of repositories for chemical or radioactive wastes compacted bentonites are considered to be favourable sealing and backfilling materials because of their high swelling capacity, their adsorption and ion-exchange ability and their plasticity in water saturated state.

Jan 1, 2005

By Simona Markic

With the aim of environment protection the program package HOMOGEN is used for realizing the planning and noxious components control in the coal produced. Using the program package PRIPREMA the division in levels and transformation (Hermite polynoms) in the N (0,1) distribution are made. By separated kriging 50 m x 50 m blocks are estimated on the levels and detailed distributions of the estimated component content are obtained. The face - longwall face is built in the blocks estimated in this way, and the direction of mining is determined. Using the stochastic simulation the distribution of the estimated production component (e.g. sulfur) on the face is obtained. Simulating the production of all faces in operation the distribution of the estimated daily mine production component is obtained. The estimated depot component is obtained in the same way. This procedure is used in the short-term planning of the estimated component movement for a given period in advance, and also in the daily production control in the case of changing conditions, e.g. the increased atmospheric pressure. The technology is successfully applied to the Velenje Lignite Mine Slovenia.

Jan 1, 1992

By Stanislaw Nawrat, Waclaw Trutwin, Waclaw Dziurznski, Janusz Roszkowski

In recent years attempts have been made to fight open and intensive mine fires by the use of special extinguishers, which are able to produce great volumes of inert gases directed into the fire zone. These extinguishers are derived from turbo-jet engines used in aircrafts and adopted for operations in mine conditions. The purpose of this paper is to draw the attention to a computer simulation method, enabling studies of dynamical behaviour of mine ventilation processes disturbed by open fires, which are also influenced by measures taken during fire fighting actions i.a. the mentioned operating extinguishers. The first part of this paper gives an account of the principles on which the computer simulation program, concerning the non- steady mine ventilation process, the fire as a heat source and the extinguisher as a source of inert gas and moisture has been based. The next part of this paper deals with simplifying assumptions and the subsequent limitations of the derived simulation pro- gram. Finally, from an example of a computer simulation, the results will be presented and relations shown between parameters characterising the ventilation process during the fire fighting action.

Jan 1, 1997

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995