Search Documents

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Kapila Pathirage, Michael S. Schultz, Gregory Sanders, Ulf G. Gwildis

Adequate understanding of the subsurface conditions along the alignment of a planned tunnel is key for managing project risk. For achieving this understanding, geotechnical borings are conducted during design. Where their spacing cannot reduce the risk of encountering differing site conditions (DSC) in-between borings to an acceptable level, supplemental exploration methodologies or data evaluation approaches may be required to bridge the data gap. This paper compares the exploration design approaches of recent tunnel boring machine (TBM) and microtunnel boring machine (MTBM) projects in the quaternary deposits along the Eastern Seaboard, the glacial geology of the Pacific Northwest, the sedimentary rocks of the South, and metamorphic rocks in western Germany, describing their respective effectiveness of managing DSC risk.

Dec 1, 2022

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By Lee W. Saperstein

P.L. 95-87 contains explicit demands for land-use planning in its reclamation and designation sections. Both sections require recognition of local land-use plans; however, the sections are not well integrated. Accommodations to these planning requirements may be found in suggestions based on British mineral planning practice. Better links can be created among local land-use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take more interest in local land-use plans and in resource inventories; states should consider devolving to local government responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 1, 1982

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019

By K. J. Shoop

An analysis of an iron ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency in the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Experiments were divided into two groups: 1) Drop testing, which was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. 2) Wet grinding, which was further divided into laboratory tumble tests and pilot plant scale tests. Laboratory tumble tests were performed to determine the effect of temperature on the grinding of iron ore. This was done by varying the percentage of fines and percentage of metamorphic clay material added to the iron ore grinding charge. The pilot plant scale tests were conducted as a scale-up of the laboratory tumble tests and to determine the effect of temperature on slurry rheology, and how this changing rheology affected the grinding of iron ore. The combined results of drop testing and wet grinding were used to make some predictions of the performance of plant scale autogenous grinding. In drop tests the breakage characteristics of the iron ore had no noticeable change in size stabilities for dry and water saturated samples over the temperature range studied (-25°C to 25°C). The effect of frozen pore water was not observed due to the low apparent porosity of the iron ore. The addition of fines to the test charge caused a decrease in the amount of new fines produced for both the laboratory tumble tests and pilot plant scale tests. The production of fines further decreased when tests were performed at the colder temperature. The increased energy consumption at lower temperatures was dominated by rheology phenomena. The addition of metamorphic clay material to the iron ore test charge resulted in more fines being produced in the laboratory tumble tests. This was due to the metamorphic clay material grinding easier than the iron ore. This caused an increase in the amount of fines in the mill, which in turn, would prematurely slow down the grinding of iron ore because of an increase in the viscosity of the slurry.

Jan 1, 1995

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By Renee Y. Allee

The Chino open pit mine, concentrator, and smelter are located in Grant county in Southwestern New Mexico. Chino Mines Company is a partnership, two- thirds owned and operated by Kennecott Santa Fe Corp., and one third owned by MC Minerals Corp. (Mitsubishi) of Japan. The concentrator, with a design capacity of 37,000 tons of copper-molybdenite ore per day, was commissioned in July, 1982. Further design modifications have resulted in an increase in throughput capacity to 42,000 tpd

Jan 1, 1986

By Robert C. Maxton

The foundry industry is a basic source of structural component for all industry. Millions of tons of castings are produced annually in both ferrous and nonferrous alloys. These castings are subjected to a wide variety of heat treatments, finishing techniques, mechanical tests and machining operations. Through all of these steps the quality of the casting is of paramount importance to the end use of the product. The Quality Assurance Program at Minneapolis Electric Steel Castings Company is designed and established to provide a superior product for both original equipment manufacturers and the mining industry.

Jan 1, 1982

By Virginia T. McLemore, Abena S. Acheampong-Mensah

Critical mineral endowment of mine wastes in two mining districts in New Mexico (Copper Flat at Hillsboro and Carlisle-Center mines in the Steeple Rock district) will be characterized and estimated. “Beta-testing” of USGS procedures was performed. Potential critical minerals at these deposits include As, Bi, Te, Zn, Co, Ni, Mg, Mn, and fluorite. pH and particle size of samples were analyzed to determine weathering and migration potential of heavy metals. Soil pH was also measured to determine the potential for Acid Rock Drainage. The pH of the waste rock piles ranged from 3.66 to 5.67 which indicates fine- grained pyrite or sulfide oxidation. The samples collected from the tailings however, showed a different range of pH, from 6.30 to 8.62, probably due to the presence of carbonates. Difference in particle size fractions and its distribution along the slope are generally influenced by natural occurrences (e.g., gravity and pre-mining hydrothermal alteration) and operational activities such as material piling or dumping. Future work includes analyses of mineralogy and particle size correlation and estimation of critical mineral endowment of these mine wastes at New Mexico.

Feb 1, 2024

By E. G. dos Santos, M. M. Veras, C. H. Sampaio, A. S. Young, R. S. Paranhos, C. O. Petter, A. C. Bastos

"The major challenges of the current mining are the energetic optimization, the lowest water consumption and minimizing environmental impact. One technique that eliminates much of the waste avoiding milling sterile, operating without water and to decrease the generation of waste at the end of the process, must be considered a major innovation. One of the most important developments in these past 10 years in the mining industry was expanding the use of high-tech sensors aimed at pre-concentration of ore. Among the mining areas where this type of technology is booming is the industrial minerals. The most common sensors are color sensors with Charge – Coupled Devices (CCD cameras) allowing through the RGB colorimetric system, the separation of minerals with different hues, and in many cases, a difference in brightness. More recently, the development of the use of dual energy X-ray transmission (DE-XRT) Dual Zone allowed the separation by atomic density of the mineral constituents of the rock. This paper presents a review of these two techniques (CCD and DE – XRT) as well some results showing the use of these two techniques for Earth Rare and Limestone. INTRODUCTION The mining industry is going through one of its biggest technological changes since the industrial revolution by the implementation of new technologies, according to Australian Mining Magazine (2015), whose theme emphasized one of the 10 greatest challenges that mining will face in the coming years. Optimization of the energy matrix in mining is focused on reducing water consumption and minimizing environmental impacts. The implementation of sensor technologies (Sensor-Based Sorting - SBS) allows elimination of mill tailings and permits the mill to operate with reduced use of water or totally eliminate this consumption (Young et al, 2016). According to Jönsson (2014) mining has undergone striking changes with the expansion of sensors of high technologies applied in the pre-concentration of mining ores. These techniques have contributed over the past 10 years in the recapture of mining areas with emphasis on the environment and/or operational optimizations. In line with the requirements of technological innovation, the mining industry is forced to make improvements in gravimetric processes ensuring better levels of Run of Mine ore feed in beneficiation plants. The implementation of automatic sorting, assisted by dual energy x-ray transmission (DE-XRT) sensor technology, or charged coupled device (CCD) image capture camera technology in the feed plant, allows for the selective sorting of individual particles into pre-concentrations (Veras et al, 2016)."

Jan 1, 2017

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By Donald R. Rathburn

Screening during the production of high-grade lump ore for blast furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date; however, others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. Normally these fines consist of the higher oxides of iron and the hydrated oxides. Unfortunately, grinding these types of materials in a wet process produces a slurry that is difficult to filter to obtain the requisite moisture level for the subsequent balling and indurating operations. The purpose of this paper is to review recent developments in fine dry grinding of iron ore and to discuss the various design and operating parameters involved. Although dry grinding of raw feed and clinker has been practiced in the cement industry for many decades, its significant application to the iron ore industry has taken place within the past ten years. Even though the basic concept of dry grinding has been borrowed from the cement industry, the successful application to iron ore grinding has not taken place without some difficulties. Consequently, the application to iron ore has required the solution of several unique design and operating problems.

Jan 1, 1970

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By Joel L. Morrison

Wet bituminous coal fines from active and abandoned slurry impoundments are currently being examined as a recoverable feedstock for the production of coal water slurry fuel (CWSF). Preliminary analysis indicates that these coal fines can be converted into low solids, low viscosity CWSF with acceptable stability without the use of viscosity modifiers (dispersants) or stabilizers. Efforts are now underway to determine if the impounded coal fines can be economically cleaned by froth flotation to an ash level of < 12 wt. % and a total sulfur content of 1.2 wt. %.

Jan 1, 1995

By Verya Nasri, Mehdi Bakhshi

The development of the Montreal metro extension Line 5 -Blue Line- toward the northeast are located between the existing Saint-Michel station and Anjou. It consists of 6-km long two-track tunnel, five new stations and six auxiliary structures. Most of the tunnel (5.5 km) will be excavated by a 9.6 m diameter shielded rock TBM and supported by a precast segmental lining system. TBM will be fitted for probing and preexcavation grouting to control water inflow into the tunnel during the excavation. This paper presents major design aspects of the TBM tunnel including alignment, geological condition, spaceproofing, precast segmental lining, and geotechnical instrumentation and monitoring.

Dec 1, 2022

By S. Miller, A. Krasner, M. Sizintsev, S. Schafrik, H. -P. Chiu, J. Sottile, A. Rajvanshi, Z. Agioutantis

In recent years, a great deal of effort has been put into automating mining equipment with the goal of improving worker health and safety and increasing mine productivity. Significant progress has been made in automating mining equipment such as load-haul-dumps and drills in underground environments where global positioning systems are unavailable. This paper addresses automating the task of positioning the shuttle-car (SC) under the continuous-miner (CM) coaldischarge conveyor during cutting and loading operations. A stereo depth camera is mounted on the SC. Machine learning based algorithms are applied on the camera’s output to identify the CM discharge conveyor and segment the scene into various regions such as roof, ribs, and personnel. This information is used to plan the shuttle car path to the CM discharge conveyor. The approach currently uses a 1/6th scale continuous miner and shuttle car in an appropriately scaled mock mine

Mar 2, 2022