Search Documents

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

A parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading on the strength and yield pattern of a stone pillar using two simplified geometry types. In type-1 the side walls of the pillars were assumed to be perpendicular to the roof and the floor, while in type-2 the side walls were assumed to be vertical. These two geometries are frequently used to simplify/model the creation of pillars in dipping mines. Results from the numerical modeling indicate that dipping pillars have reduced strength compared to horizontal pillars, and they are at an elevated risk of failure. Also, an asymmetric failure propagation pattern could be obtained depending on the interaction between the pillar width/height (W/H) ratio, seam dip, in situ stresses and pillar geometry.

By John W. Motter

The Green Mountain Copper Prospect is an unusual stratiform base metal occurrence located in the California Foothills Copper-Zinc Belt. Mined for rich secondary oxide-carbonate ores since 1863, the first serious exploration of the primary ores was in the 1970's. Unlike typical volcanogenic deposits of the district, stratigraphy consists of greywackes overlain (?) or intruded by an intermediate to felsic volcanic unit. Shales and siltstones overlie the volcanic unit. Massive pyrrhotite, chalcopyrite and sphalerite occur at the top of the volcanic unit. Later intrusion and deformation metamorphosed the sequence and created a SW plunging anticline. Characteristic magnetic and electrical geophysical signatures are present and reviewed.

Jan 1, 1978

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By Jennifer L. Bell, PATRICK L. YORIO, Emily J. Haas, Susan M. Moore, Lee A. Greenawald

Although researchers have struggled to replicate Heinrich’s safety triangle findings (Heinrich 1931) for various reasons (e.g., no access to his original database and it is unclear if the database was of a single establishment/operation or for an entire industry), the occupational safety community has continued to adopt and expand the applications of this theory (e.g., McSween 2003). Within the mining industry, the potential exists for operations and companies to use concepts from the safety triangle as a way to inform or challenge the practices employed within their health and safety management systems (HSMS) to prevent incidents (Backlund 2016). This paper considers data obtained from the Mine Safety and Health Administration’s databases and demonstrates the validity of applying the safety triangle theory at the mine level. The results support the use of this theory and demonstrate that lower severity incidents can predict fatalities in a subsequent year where significant nuances and caveats to applying the theory are identified and discussed.

Jul 25, 2020

By Whitmell J. Smithwick

Lime is one of the most extensively used chemicals in industry. Other than sulfuric acid, it is used in greater quantities than any other man-made industrial chemical. In 1974 there were 20,368,000 tons of lime used in the United States, which amounts to approximately 190 pounds for each man, woman and child in our nation. Lime also is perhaps the most diversely used of any industrial chemical. It is used in such areas as pharmaceutical, chemical, steel making, glass making, production of copper and aluminum, sugar refining, agriculture, construction, ecological endeavors, potable water treatment and sanitation. Figure I lists the major uses of lime for 1974, which is the latest year for which this data is available. The impact of the use of lime for ecological reasons did not show up to any appreciable extent in 1974, but we expect this to be a significant factor within the next few years. Fortunately, in the United States and also in most of the world, there are many deposits of high quality limestone available for the production of hood quality lime. For this discussion, we will assure that a limestone of a suitable quality and size consist will be available in a storage bin or stockpile near the kiln. Quality requirements for the lime product will be covered. We also will give a brief description of the three most popular types of lime calcining systems, how they function, and expected lime product quality from each of these. Commercial fuels and major accessory equipment will be discussed briefly.

Jan 1, 1976

By Paul R. Kruesi

A patent-applied-for process has been developed in which zinc chloride is extracted by tributyl phosphate in kerosine, and stripped with ethylene glycol or ammoniated ethylene glycol. The anhydrous zinc chloride is precipitated from the glycol as the ammine and zinc chloride is prepared by thermal decomposition with recycle of ammonia. The process permits the production of high grade zinc from scraps and drosses. Its applicability to the recycling of zinc will be illustrated.

Jan 1, 1984

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By J. Richard Kyle

The Pb-Zn ore bodies in the Pine Point district are localized in paleo-solution structures that developed as the result of post-middle Givetian subaerial exposure of the carbonate barrier complex. Sulfides are concentrated in transgressive pale-solution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character, one of which contained metals and the other reduced sulfur. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition. District and ore body metal distribution patterns may reflect the nature and movement of mineralizing fluids.

Jan 1, 1979

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth's surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth's surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997

By Yakup Cebeci, Leyla Kalender, Ceylan Yarluğkal Altınışık, Hikmet Sis

The abstract highlights the challenges in concentrating complex and non-sulfide lead-zinc ores and emphasizes the importance of froth flotation for their beneficiation. The study focuses on using process mineralogy to understand the flotation behavior of these ores from the Görgü region. The ore samples were characterized using various techniques, revealing oxidation and carbonation of primary minerals. The flotation results were interpreted in light of the mineralogical data, explaining the poor outcomes due to the complex nature of the ore, poor liberation, and lack of hydrophobicity.

Mar 22, 2022

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By D.G. Osborne

Each month abstracts of the papers selected for the Annual Bound TRANSACTIONS Volume will appear on this page. Since the Annual Bound Volume will not be published until the spring of next year, this will give people an opportunity to order copies of the papers earlier. If you would like copies, fill out the coupon below and return it to SME-AIME. Each copy will cost

Jan 1, 1985

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step-function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step-function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another is-sue is how they compare to peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974