Search Documents

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By A. Salmoni, E. K. Gillin, T. Eger, A. Cann, P. Vi, M. Hunt

Kittusamy (Kittusamy & Buchholz, 2004) state that there have been few studies conducted to assess exposure to whole-body vibration (WBV) in the construction industry. They suggest that there is very little reliable data from the construction industry that characterizes exposure levels to various hazards including WBV or the health outcomes from such exposure and that there is a need for more exposure data. In a recent exploratory study of heavy construction equipment Cann (Cann, Salmoni, Vi, & Eger, 2003) looked at vibration levels for 14 different types of construction equipment. Eight of the 14 pieces of equipment tested exposed operators to levels of WBV that exceeded the recommended limits for an 8-hour period when comparing the measured VDV to the ISO 2631-1 standards. The purpose of the present research was not only to test a larger number of scrapers but also to investigate scraper operator exposure to whole body vibration (WBV) separately for each task. Methods 33 scrapers were evaluated for WBV in a variety of residential and road construction projects. Testing equipment consisted of triaxial accelerometers that allowed vibration data collection in all three orthogonal axes, with the x-axis positioned to measure vibration in the anterior-posterior direction, the y-axis in the medial-lateral direction, and the z-axis in the vertical direction. Root mean square accelerations (aRMS), vibration dose value (VDV), crest factor, and maximum transient vibration values (MTVV) were derived from this software and exported to an Excel™ spreadsheet for later data analysis. Test sessions for each piece of equipment lasted for approximately 20 minutes until at least three work cycles had been completed. Tasks included: idling while waiting for a bulldozer to push the scraper through the scraping phase, scraping, traveling loaded with dirt, dumping and traveling empty. Results Task breakdown by time reveals 25% of the work cycle was spent traveling fully loaded with dirt, 19% dumping, 21% traveling unloaded, 17% idling and 18% scraping. Calculation of aRMS vector sums gave values of 2.55 m/s2 during loaded transport, 2.46 m/s2 during dumping, 2.31 m/s2 during unloaded travel, 0.55 m/s2 during idling and 1.46 m/s2 during scraping (see Table 1). The highest acceleration values recorded were found in the z-axis during fully loaded transport reaching an average aRMS over three work cycles of 2.55 m/s2.

Jan 6, 2006

By J. W. Paul

The material that composes the roof in coal mines differs in strength according to variations in its physical nature and characteristics. Some material such as limestone and massive sandstone, (free from slits) and carbonaceous shale or bone, will often remain in place in narrow work without the use of timber or other means of support, but in wide places the use of supports becomes a real necessity. Roof material composed of shale, fire clay or small laminations of sandstone, or shale or sandstone interspersed with laminations of thin coal, presents conditions that call for timber support in both narrow and wide work. However, in narrow work such unstable roof material may be taken down until the strata assume an arch that is self-supporting for overlying firm strata such as a roof coal, a touch weather-resisting, shale, sandstone, or limestone. The proper support of the roof in roadways used for haulage or travel adds to the economy of operation by preventing delays in transportation and increases the safety of those who travel these roadways.

Jan 1, 1930

In 2006, a total of 4,573 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 30.7% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,042; 44.7%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=368; 8.0%), followed by Texas (n=342; 7.5%).

Jan 1, 2008

To provide a means for accurately and reliably warning of impending roof falls or rock bursts and for evaluating support systems. The Approach: Development of a device for measuring rockbolt loads which is not affected by harsh environments nor by eccentric loading conditions and is easily adapted to various size rock bolts. How It Works: The Rock-Bolt Tension Load Cell, developed by the Bureau's Spokane (Wash.) Mining Research Center, is installed on a bolt and sandwiched between a conventional doughnut washer bearing plate and a torqueing nut (Fig. 1). As the bolt takes load, the bearing plate transmits the load axially to the cell through a ball and socket arrangement, compensating for uneven bearing surfaces. The cell body strains in proportion to the applied load: the strain is sensed by welded strain gages as change in electrical resistance. The resistance change is read through a Wheatstone Bridge and, through calibration, the applied load is determined.

Jan 1, 1974

By W. E. Brown, P. R. Porath, V. Miller, C. E. Wood, C. Prasky, E. P. Barrett

"INTRODUCTION This investigation was a part at the Bureau of Mines program for the production of critical and essential materials needed for the war.The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from low grade ores of Minnesota.OBJECT OF INVESTIGATIONThe investigation was conducted by the Bureau of Mines to ""determine the workability of the proposed bubble-hearth process and its possible use in connection with an experimental plant for the gasification of lignite being operated by the Coal Division of the Bureau of Mines at Grand Forks, North Dakota.ACKNOWLEDGMENTSThis report is one of many on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources.Investigations of our mineral resources are conducted by the Mining Branch, L. B. Moon, chief, and by the Metallurgical Branch, O. C. Ralston, chief.The scope of the report falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficulty beneficiated ores, the production of pure metals from domestic deposits, the exploration of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice."

Jun 1, 1947

By V. F. Parry, J. B. Goodman, W. S. Landers

"This investigation was conducted: under the direction of A.C. Fieldner, chief, Fuel and Explosives Branch, Bureau of Mines, Washington, D. C. The following members of a Technical .advisory Committee were helpful in advancing the investigation: L. C. Harrington, dean, College of Engineering, University of North Dakota; D. F. Pane, president, Sheridan-Wyoming Coal Co.; Carson W. Smith, president, Consolidated goal & Coke Co.; Durbin van Law, consulting, engineer, Denver & Rio Grande Western Railroad; and C. B. Carpenter, professor of metallurgy, Colorado School of Mines. Coal samples from the Northern Colorado field used in the stoker during 3 years of service were supplied through the cooperation of N. C. Brooks, secretary, Northern Colorado Coals, Inc.This report describes the development and practical tests made on a small stoker-fired system for heating service water automatically. The system was designed to take advantage of the favorable reactivity of low-rank fuels, and the objective was to devise a combination of stoker, heat-receiving, and hot-water storage system Which would be automatic for at least 30 days without attention, while heating service water at minimum cost. The system was developed to a point where coal consumption was less than 10 pounds (or less than 100,000 B.t.u.) per day. The total operating cost of hot water for an average-family-was about $1.00 per month, with coal retailing at $6.00 per ton and electric power at 4 cents a kilowatt-hour. The heating system was designed for the utilization of low-rank fuels, but the general features of the double-tank system can be 'employed fuels, either gas or liquid fuels.The Subbituminous Coal and Lignite Section of the Bureau of Mines began investigations on the utilization of low-rank fuels in domestic appliances during 1939. Tests were made on various devices to find out if they were suitable for the low-rank fuels. Most of the available appliances for burning coal have been designed for the higher-rank fuels, and they are not well-suited for burning the lower-rank coals at maximum efficiency, because subbituminous coals and lignite have high bed moisture ranging between 20 and 40 percent by weight, which lowers heating value to the range of 10,000 to 6,500 B.t.u. per pound. They are noncoking, and the ash content ranges between 4 and 6 percent, with a fusion temperature of about 2,0000 F."

Jun 1, 1946

By L. R. Herrmann

The research described in this report is the first phase of a comprehensive program for the development of a characterization for the structural properties of rock masses. The mathematical expression of the characterization is especial' tailored for use in conjunction with modern structural analysis procedures. The objective of the first phase of the project is to determine the feasibility of representing the structural properties of rock masses in terms of the analysis of an appropriate "representative volume" the results of this investigation are described in detail in the body of the report. The current state-of-the-art concerning the understanding and description of the fundamental mechanisms of rock behavior are determined from a survey of existing literature. The development of a representative volume that captures the most important of these mechanisms is described, In order not to unduly obscure the fundamental aspects of this development, the mathematical analysis of the representative volume is limited to plane strain conditions. A subroutine for the numerical evaluation of the proposed model (i.e., the analysis of the representative volume) is presented. The steps necessary for the incorporation of the subroutine directly into existing two-dimensional finite element structural analysis programs are described. Comparisons between the predictions of the proposed characterization and published results of simple laboratory tests are presented and discussed. Finally recommendations are given concerning suggested improvements of the model and the extension of it to the general three-dimensional case.

Jan 1, 1974

By E. Chin

The countries of Asia and the Pacific have large resources of diverse minerals. Australia and China have extensive mineralization that are commercially being exploited. The major minerals in Australia with known reserves adequate for both domestic demand and export markets include bauxite, clays, copper, diamond, gold, iron ore, lead, manganese, mineral sands (titanium minerals), nickel, salt, silver, tin, uranium, and zinc. China is the world leader in proven reserves of antimony, barite, magnesite, molybdenum, rare earths, titanium (ilmenite), tungsten, and vanadium. It also has about 55 billion tons of iron ore, albeit with an average grade of only 30 % to 35 % elemental iron content. With the exception of chromium and copper, China has significant resources of a wide array of minerals and metals, based on its production and/or export capability for these commodities. Additionally, India has significant resources of bauxite and mineral sands; Indonesia, bauxite, copper, nickel, and tin; Malaysia, tin and associated titanium; Mongolia, copper, fluorspar, and lead-zinc; New Caledonia, nickel; New Zealand, gold and iron sand; North Korea, magnesite; Papua New Guinea, copper, gold and mineral sands; Philippines, copper, chromite, and gold; and Sri Lanka, gemstones. Moreover, there appears to be extensive mineralization III Burma (Myanmar), Cambodia, Laos, Thailand, and Vietnam, but they have yet to be definitively delineated.

Jan 1, 1994

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By L. C. IlsLey

"During the last eight years there has been a noticeable increase in the use of permissible equipment in gassy and dusty coal mines. This trend has undoubtedly been toward greater safety in mining, but in spite of this all is not well ""along the front.""In many mines those in charge, either through ignorance or supposed economy, have neglected to install sufficient copper and maintain good bonding on the rails used for return circuits to have a safe working voltage for the permissible equipment which is intended to afford them safety.Low voltage, when properly analyzed, is not economy but frequently is an expensive oversight. Burned-out armatures, controllers, rheostats, and switches are costly in themselves to repair or replace, but the greatest cost in many instances is the loss of production resulting from idle and broken-down equipment.From a safety standpoint, excessive low voltage where permissible equipment is necessary is almost criminal negligence. A burn-out of any kind is liable to cause an arc that may burn its way through a casing wall and bring about a hazardous condition if gas or dust in explosive proportions should be present. Again, all wiring, both interior and exterior to the apparatus, is subject to the extra heating consequent upon low voltage. It should be remembered that if the voltage drops the current must increase a corresponding amount in order that the same work may be accomplished; and as the heating effect is as the square of the current, an enormous overheating of the electrical parts and wiring often takes place. This heating effect is especially detrimental to trailing cables used on portable equipment, because under the most favorable conditions the size of cable selected is only barely sufficient to do its work properly at a safe working temperature; therefore, when the extra current load is added because of poor voltage, overheating is sure to result, with consequent deterioration of the insulation, This effect greatly increases the liability of cable failures in service, and in turn adds to the hazards incident to the use of portable equipment of the permissible type involving the use of trailing cables.Some manufacturers have tried -to protect their equipment from low voltage, especially below a certain point, by -installing low-voltage relays which will trip when the voltage falls to a predetermined value. It is understood that some operators have hesitated or refused to install such low-voltage protection because they were aware that the voltage conditions were so poor that the equipment could not operate under the safe limits set. It is difficult to understand how any progressive company that is willing to go to the ex-pense of installing permissible equipment could be so shortsighted in this phase of common sense, safety, and economy."

Dec 1, 1929

By Henry P. Chandler

COMBINED sales of abrasive materials in the United States during 1956 increased at about the same rate as the value of the Gross National Product in terms of 1954 dollars,3 which was nearly 3 percent. However, some segments of the industry did not follow the general pattern. Sales of abrasive grinding wheels increased 9 percent in value. Sales of surface-coated abrasives declined 5 percent in quantity hut increased 1 percent in value, Production of crude silicon carbide in the United States and Canada advanced both in tonnage and value, but that of abrasive-grade [ ]

Jan 1, 1958

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry's interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994

By John R. McDonnell

The Valle Vidal Unit comprises 100,000 acres In Taos and Colfax: Counties, New Mexico. The unit was donated to the American public In 1982 by the Pennzoll Co. and is administered by the U.S. Department of Agriculture Forest Service as an addition to the Carson National Forest. During 1990-1991, the Bureau of Mines conducted a mineral Investigation of the unit as authorized by an Interagency Agreement (1987) Intended to assist the Forest Service to incorporate mineral resource data In forest plans. The Bureau reviewed literature and records concerning mineral resources and mining activity, and performed a field examination of mines, prospects, and mineral occurrences in and near the Valle Vidal Unit. The La Belle mining district encompasses most of the western part of the Valle Vidal Unit. The district was most active between 1893 and 1902, after the land grant was opened to prospecting and gold discoveries were reported. The discoveries were low grade, and eventually were abandoned. The Bureau's appraisal of the district determined that lode gold occurs primarily in fissure veins in volcanic rocks, and placer gold occurs In weakly cemented sedimentary rocks and alluvial sediments; but at a grade that is currently considered subeconomic. If the price of gold increases in the future, prospecting and exploration in the area may be renewed, but the activity would likely be limited due to "acquired land status" restrictions, which require mineral leasing and prohibit claim location in the Valle Vidal Unit.

Jan 1, 1992

By Raymond B. Ladoo

[Inquiries are frequently received by the Bureau of Minas relative to occurrence, mining, treatment and utilization of the natural hydrocarbons' such as gilsonite, elaterate, wurtzilite, grahamite, and ozokerite although have been known and used for many years, they are not yet well understood and the amount of recent literature dealing with them as comparatively small. This paper is intended merely to summarize the present knowledge The natural hydrocarbons included in this series are gilsonite, elaterite, wurtzilite, glance pitch, manjak, grahamite, albertite, arid ozokerite and many other minor varieties. With the exception of ozokerite and the other mineral waxes, then all more or less resemble asphalt in that they are dark brown or black bituminous substances of organic origin, generally with a resinous luster. Ozokerite usually light an color with a waxey luster, is closely allied to the others of the series, but is usually considered separately, Unfortunately authorities differ as to nomenclature so that determinations of physical and chemical properties from different sources may riot be readily compared. Abraham Herbert, Asphalts and Allied Substances, 1918, 606 pp. has made one of the most detailed studies of these subjects in recent years, and his classification is used in the main. The following definitions are given by him]

Jan 1, 1920

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006

By Michel C. Frippel

This section of the Minerals Yearbook reviews the minerals industries of 45 countries: the 12 nations of the European Community (EC) (Belgium, Denmark/ Greenland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, and the United Kingdom); 6 of the 7 nations of the European Free Trade Association (EFTA) (Austria, Finland, Iceland, Norway, Switzerland, and Sweden); Malta; the 11 Eastern European economies in transition (Albania, Bosnia and Hercegovina, Bulgaria, Croatia, Czechoslovakia, Hungary, Macedonia, Poland, Romania, Serbia and Montenegro, and Slovenia); and the countries of Central Eurasia (Armenia, Azerbaijan, Belarus, Estonia, Georgia, Kazakhstan, Kyrgystan, Latvia, Lithuania, Moldova, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan).

Jan 1, 1994

By Fred N. Kissell

In This Chapter [Instruments available to measure methane in mines and tunnels Using a portable detector in both accessible and restricted spaces Machine-mounted monitors: placement and response time Calibration of catalytic detectors for different gases and Misinterpreting warning signs This chapter gives guidelines for methane measurement in mines and tunnels. The emphasis is on the measurement procedure and the interpretation of the measurement rather than on the instrument itself.] The failure to properly sample for methane is a major contributing factor to methane explosion risk. Sampling errors are most likely to occur at mines or tunnels where the presence of methane is not suspected or during nonroutine tasks at mines or tunnels known to have gas. More specific information on methane sampling at continuous miner sections is in Chapter 3. Chapters 4 and 5 discuss sampling at longwall sections, and Chapter 14 discusses sampling at tunnels. METHANE DETECTORS FOR MINING Many models of gas detectors are available to measure methane concentrations, as well as most of the other contaminant gases found in mines and tunnels. An example is the iTX Multi-Gas Monitor, a portable gas detector available from Industrial Scientific Corp., Oakdale, PA. This handheld instrument measures several gases simultaneously. The cost (2004) ranges from $1,300 to $2,200, depending on the number of gases measured. Similar instruments are available from other manufacturers. Most methane detectors used in mining use a catalytic heat of combustion sensor to detect methane and other combustible gases. These have been proven through many years of reliable operation. For detection of methane, proper operation of catalytic heat of combustion sensors

Jan 6, 2006

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1984 was $409.8 million, and established a new record high for value of nonfuel minerals in the State, at 13.4:% over the previous high of 1983. Output of nearly all nonfuel minerals increased; phosphate rock was one of the exceptions, with no recorded output in 1984. Cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in fire clay and kaolin; fourth in bentonite, ferroalloys, and dimension marble; fifth in masonry cement, lime, and recovered sulfur; and sixth in portland cement. Alabama ranked 22d in the Nation in value of nonfuel minerals produced.

Jan 1, 1986

By Ronald B. Hollenbeck

The value of mineral production in Alabama continued to increase and reached a new high of $260 million, 3 percent above the previous high established in 1967. Record high values were reported for bentonite, crushed marble, lime, miscellaneous clay, portland cement, salt, sand and gravel, and scrap mica. The value of coal, total cement, petroleum, and stone accounted for 87 percent of the State's total value of mineral production. Alabama ranked second among the States in the production of bauxite and scrap mica and third in kaolin, masonry cement, and native asphalt.

Jan 1, 1970