Search Documents

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By Mahdi Shevrini, Hamed Haghi

"In this research, the operation of screen classifying in silica processing circuits was investigated and modified by replacement of available trommel screens with teetered bed separator (TBS). In addition the effect of the mentioned replacement and addition of attrition scrubber on quality of final product, impurities removal, recovery and production rate were inspected. Considering screen efficiency problems to achieve certain particle size distribution, hydraulic classifying system was selected instead of trommel screens. Application of suggested plan improved quality and particle size distribution of produced silica significantly. Optimization of size classification in process circuit resulted in increase in production rate up to 21% (from 67% to 81%), silica recovery (from 68.35% up to 83.11%) and relative enhancement in removal of impurities such as Fe2O3 and TiO2. After optimization and stabilization of grinding and size classification section, industrial attrition scrubbing tests were carried out and the best solid percent and retention time were determined i.e. 70% and 6 minutes, respectively. Using sodium carbonate during attrition scrubbing, has major effect on removal of surface coating and staining especially sharp increase in clay removal; therefore 2 kg/t of sodium carbonate can be optimistic point of industrial procedure for this silica processing plant. It should be mentioned that application of attrition scrubbing which is followed by screw classifier for de-sliming were useful for better cumulating of particles in the range of appropriate liberation degree (+106-300µm) and efficient removal of metallic (iron and titanium oxides) and non-metallic (clays and feldspars) impurities."

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

The Indian steel industry is growing at a rapid pace and expected to be the 2nd largest steel producer in the world after China. To cope up with this growth and to sustain it, the industry needs to focus on effective utilization of domestic metallurgical coals. While the importance of indigenous coal has increased, its supply from the domestic sources is declining. This is primarily due to high ash content in Indian coals leading to its difficulty in washing to a low level competitive to imported coals. Non-availability of a suitable beneficiation technology to bring down the ash to such a low level is the other reason. Effective utilization of current technologies has enabled Tata Steel to bring down the ash to 13-16% from its captive collieries. However, further lowering the ash using the conventional beneficiation technologies is difficult and unsustainable. New technologies should be developed for bringing down the ash further. A thrust area research program has been undertaken at Tata Steel for producing clean coal with 8% ash maintaining the yield currently achieved in its washeries. The technologies attempted are based on chemical beneficiation of coal. In leaching process, suitable chemicals are used for extracting ash minerals from the coal. As an alternative process, the combustible part of the coal is being extracted using a suitable organic solvent through an organo-refining process. Both the processes have been successfully developed in the laboratory and are being demonstrated in pilot scales. Various beneficiation processes practiced at Tata Steel including the efforts made for developing new processes for achieving clean coal with 8% ash have been discussed in this paper. Keywords: metallurgical coals, washing, beneficiation technologies, chemical beneficiation, leaching, solvent, and organo-refining process

Sep 1, 2012

By P. V. Ramesh Babu

India has sizeable number of small deposits of rare metal bearing minerals namely columbite-tantalite, pyrochlore, beryl, lepidolite, spodumene and rare-earth element bearing minerals monazite and xenotime in different parts of India. Pegmatites, alkali granites, syenites, and the derived gravel and soils are the main source for rare metal and rare earth (RMRE) minerals. The RMRE minerals are classified as prescribed substances under Atomic Energy act of 1962 keeping in view the uses in the nuclear industry. Atomic Minerals Directorate for Exploration and Research (AMD) of Department of Atomic Energy (DAE) is the sole agency responsible for exploration and exploitation of RMRE minerals in India since 1962. The latest technological advancements and applications in the field of space, electronics, communication and nuclear industry using these metals and their products have necessitated to augment the production and resources of RMRE minerals. These minerals play a significant role in the technological and economic development of the country. The light rare earth element bearing mineral monazite is abundant in beach sands and is being commercially exploited by Indian Rare Earths Limited (IREL). Columbite-tantalite, the chief source for niobium and tantalum (Nb-Ta) metals present in the pegmatitic gravel are recovered by small mobile beneficiation plants. The cut and fill method of mining adapted is eco-friendly. The processing flow-sheet consists of wet sizing at ½ in and 1mm followed by gravity concentration of sized products utilizing the methods of jigging and wet tabling. The sizing equipment include revolving and vibratory screens and the gravity concentration equipments used are fixed sieve jigs and movable screen jigs for final upgradation. The gravity concentrates are further upgraded by magnetic separation to remove magnetite and ilmenite. The mine areas are reclaimed by filling with coarse size tailings and new plantations. These mobile pilot plants were earlier operated in Bihar mica belt, Jharkhand, pegmatitic areas of Karnataka and Nellore mica belt of Andhra Pradesh and are currently being operated in Bastar-Malkangiri pegmatite belt of Chhattisgarh and pegmatites of Jharsuguda district of Orissa. Beryl, lepidolite, spodumene and cassiterite minerals are the by-products from the pegmatite ores. Fergusonite, samarskite and microlite are the other niobium and tantalum bearing minerals which are also found in pegmatites. Xenotime, the chief mineral of yttirium generally occurs in granites and pegmatites. The rare earth minerals monazite and xenotime get concentrated in the placer sands of rivers and beaches. The occurrence of xenotime in the sands of Siri River and Deo River in Chhotanagpur granitic terrain in parts of Chhattisgarh and Jharkhand are an example. These sands containing 1-2.5% heavy minerals were processed by a mobile plant consisting of sizing equipments like trommel and vibratory screen followed by separation of heavy minerals from -1mm sands with the help of gravity concentration equipments like spirals/shaking tables/sluices. Xenotime and monazite from the pre-concentrate are further separated by magnetic and electro-static methods. The present paper illustrates the pilot plant set up for the recovery of rare metal as well as rare earth minerals. Keywords: small deposits, rare earths, rare metals, pegmatite, Nb-Ta, xenotime, India

Sep 1, 2012

By Zhiyong Gao, Ruiying Fan

"Crushing and grinding are the prerequisite processes in many industries, such as minerals processing and powder technology. During crushing and grinding, minerals will cleave or fracture along the directions by broken the interlayer bonds (e.g., ionic bonds), generating some commonly exposed surfaces. The broken (or dangling) bonds at the generated surface makes the surface more active and determine the reactivity of the surface. In this work, the population of broken (or dangling) bonds on commonly exposed surfaces of fluorite mineral (a chosen model mineral) was calculated. Based on the calculated broken bonds information, the anisotropic surface reactivity of fluorite such as surface energy, surface relaxation, dissolution, wettability, surface charge and adsorbability, were discussed. The results show that the surface broken bonds density, which is positively related to the surface energy, can be used to predict the cleavage nature, surface relaxation degree and surface stability of fluorite crystal. The distribution characteristic and the number of broken (or unsaturated) bonds of surface active atoms (like Ca for fluorite crystal) can be used to predict and explain the anisotropic wettability, surface charge and adsorption mode and strength of organic molecules on different commonly exposed surfaces. It is easy to conclude that the calculation of surface broken bonds can serve as a fast and accurate way to start the mineral chemistry studies. These findings will be helpful to the mineral/material chemistry research in related interfacial science communities.INTRODUCTIONGrinding for mineral liberation is a prerequisite for a successful flotation separation. Also grinding for size reduction is a prior process for a favorable powder technology. During the grinding process, the minerals / materials will cleave and fracture along certain crystal directions with relatively weak interlayer chemical bonds1 to form a number of common exposed surfaces. Exposed surfaces are the outer boundary of a solid substance. In the mineral / material block, the bonding orbital of the atoms is filled with electrons and the atoms are in a steady state. Atoms on these exposed surfaces appear to show dangling bonds (or broken bonds) by losing chemical bonds to adjacent atoms in the previous block. Therefore, surface broken bonds serves as an initial property of a fresh surface. The lattice arrangement and crystal orientations causes differences in the number of dangling bonds on each exposed surface, i.e., anisotropic surface broken bonds2. The anisotropic dangling bonds enable the exposed surfaces to show varying degrees of surface reactivity (including surface energy, surface charge, surface relaxation, dissolution, wettability and adsorption behavior), known as anisotropic surface reactivity."

Jan 1, 2018

By Tiago de Souza, Caroline Gonçalves, Carlos Eduardo de Castro, Everton Dias

The Miraí plant from Votorantim Metais, has two screening stages to the bauxite classification after scrubbagem. The final product has hold the larger size of 0,84 millimeters (20 mesh). There are two sieves Haver & Boecker (model R-TE 3658 x 10972), which have four modules with cut size sieves of 10 mesh (1.70 millimeters) and ¼ inch (6.35 millimeters) on the primary screen, and 20 mesh (0.84 mm) on the secondary screen, all made of polyurethane. The actual configuration was established according to the empirical tests realized that aimed the increase material load on the secondary screening. However, having in mind the screening process improvement and use the fractions smaller than 0,84 mm, which have significant levels of Alumina and low reactive silica, was proposed a new test of change the sieves opening for 6 mesh in the primary screen and 28 mesh for the secondary sieve. The objective of this work was measure the ore alterations on the particle size distribution on the screening steps, increasing the plant weight and ratio recovery before and after the test.

Jan 1, 2014

By Hemant Nerurkar

The destination of human development journey is envisioned as human well being. Human well-being is the extent to which individual share the ability and the opportunity to live the kinds of lives they value it includes environmental security, good health and living conditions, all of which are closely related to each other. The breakthroughs, which transformed the human race, have close interdependency with the environment. With the increase in world population, the requirement of natural resources is increasing every day. The nature is still stronger than man is but we must use natural resources more responsibly. The key to our well being is sustainable development Development effort for human well being may have adverse impact on the environment also. To keep the net impact positive is critical for sustainable development. For mineral processing industry, the value of a mineral is in the actual value as perceived by the end user. The process designs, investments in technology development all have direct relationship with the value of use and making a net positive impact on our ecosystem The value proposition has shifted towards raw materials and is a big differentiator. The availability of good quality raw material is difficult or is available at a premium. The challenge today is to develop green technologies that make effective and efficient usage of low grade raw materials The low grade raw materials as available pose a significant opportunity for human race for delivering value. They offer an easier reach to a value as perceived in end use but the journey is full of challenges. The first challenge is development of technology for maximizing grade recovery as required by the downstream process. The second challenge is to make the technology viable so that it contributes value to end use and the third challenge is to keep the net impact of the process positive The mining and mineral processing fraternity, being at the beginning of this value chain is set to take the first step in this journey for a tryst with ultimate human well being. Keywords: sustainable development, challenges in mineral processing

Sep 1, 2012

By M. V. S. Cavalcante

The quality of iron ore pellets, represented in terms of parameters such as cold compressive strength (CCS) and Tumble Index (TI), has a strongly influence on the productivity and energy of reduction furnaces like the blast furnace and on the quality of hot metal or liquid iron. The main objective of pelletization operations is to produce iron ore pellets of desirable specifications and ensure high levels of plant productivity and energy efficiency. Advanced process control of an industrial iron ore pellet induration process using a soft sensor for pellet quality and fuzzy-logic based control algorithm is described in this paper. The pellet quality soft sensor consists of a rigorous mathematical model of the induration process and a statistical model for the pellet quality parameters. The mathematical model is based on the fundamental principles of heat and mass transfer between gases and pellets, kinetics of drying and condensation of moisture, combustion of coke, calcination of limestone, and melting and solidification of pellets. The predictions of wind-box temperature profiles are in close agreement with the measured profiles. The time-temperature profiles of the pellets during induration, along with raw material characteristics and induration process operating conditions, are used as inputs to the quality model to predict cold compressive strength and the Tumble Index. The predictions of the quality soft sensor along with the rules based on fuzzy-logic derived from simulation results and operator experience are then utilized to control the induration process to achieve precise control of the quality parameters and to optimize the induration process in terms of fuel efficiency and productivity. The mathematical model is also utilized as a soft sensor for temperature, moisture and composition profiles of pellets and gases. Results of implementation of this model-based control strategy on an industrial scale induration process will be presented. Keywords: iron ore, pelletization, simulation, process control, optimisation

Sep 1, 2012

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

By G. Bulut, Ü. Yenial

"Heavy metals contamination in aqueous systems can be found in a variety of industries, in particularly mining, metal processing, finishing and plating. Water containing more than 0.5 ppm heavy metal considered as a toxic due to harmful effects on health. The major techniques employed for heavy metal removal from industrial wastewaters include precipitation, reduction, ion-exchange, and adsorption. Adsorption is a heavy metal removal method for aqueous systems. As a common adsorbent, activated carbon has been used in treatment but it is ineffective on some elements. Thus, there has been a research for developing highly effective and selective adsorbents. In this study the adsorption of lead and arsenic ions on to coal waste and red mud waste was studied. The experimental parameters were determined as pH, equilibrium time and the initial concentrations, activation by heat treatment and the blend of adsorbents. According to their adsorption capabilities, red mud was found to adsorb lead and arsenic ion with high efficiency but coal waste did not adsorb arsenic ion. However the binary adsorptions of these ions were enhanced the adsorption efficiencies. In addition the blend of coal waste and red mud affected the adsorption efficiency. INTRODUCTION As a result of rapidly developing industry and excessive use of water resources, the need of clean water and wastewater management appear as a problem. Wastewater recycling activities and researches come to the fore for an effective use of wastewater. Recycling of wastewater, which contains heavy metals harmful to the environment and human, is a difficult process. Heavy metals are generally divided into three categories: toxic metals, precious metals, radionuclides. Wastewaters from various industries, containing heavy metals, are the main polluters of water and soil. Although their toxic structures, heavy metals are used extensively in industry as they have technological significance. Usually mining industry, metal industry and industrial organizations produce heavy metal containing wastewaters (Volesky 1990, Ting and Lawson 1991, Bishop 2002)."

Jan 1, 2018

By Katarina Theander, Robert J. Pugh

The generation of froth with a critical degree of stability and height is an important aspect of the froth flotation. In this paper we have studied the synergism and anti-synergism in frothing behaviour in a mixed flotation collector/frother mixture (a model fatty acid; sodium oleate and a model frother; nonionic (polyethyleneoxide alkyl C14E6). Values of the collector / frother molecular interaction parameters (the ß-parameters) were determined from the surface tension data using regular solution theory. The frothing characteristics of the system were evaluated using a glass column equipped with a series of conductivity electrodes, which enabled the water content of the froth to be determined. From these measurements, the dynamic frothability and static froth stability were determined. It was concluded that the synergism/anti-synergism in frothability was depended on the molecular composition of the surfactant system, the diffusion of monomer to the thin film interface and on the breakdown of the mixed nonionic/anionic micelles.

Jan 1, 2003

By A. Mainza, H. Hill, L. S. Bbosa

"Impact breakage is the most elementary size reduction mechanism in comminution devices. In comminution research, characterization of breakage is primarily concerned with the energy expended to cause it. The main challenges of this approach have been quantifying the actual energy requirements of impact breakage and developing mechanistic models to accurately describe the process. For engineering load analysis, fracture is characterized in terms of strengths such as yield stress and ultimate tensile stress, which govern the maximum loads specific materials can be subjected to before irreversible inelastic deformation and subsequently complete fracture occur. With this approach, the main challenge has been to elucidate the underlying mechanism, in the means that the load causes weaknesses in the material microstructure to act as sites for stress concentrations, leading to crack initiation, propagation and eventual failure. Studies dedicated to investigating particle fracture under impact loading have led to the development of several devices for conducting breakage characterization tests. These devices include the drop weight tester, split Hopkinson pressure bar, rotary breakage tester and the short impact load cell. All these have different particle loading and breakage methods, and thus can yield distinct information which can be compiled together to study a material and the nature of breakage. This work analyses the single impact breakage data obtained across the listed devices. A homogenous ore commonly known as blue stone is used for all breakage tests. The work is conducted using standard procedures specific to each device as closely as possible. Drop weight and rotary breakage tests were used to obtain hardness parameters based on an existing t10 breakage model, while split Hopkinson pressure bar and short impact load cell measurements provided properties based on conventional engineering load analysis. The results were used to highlight the significance of the loading geometry, impact mechanism and impulse on the extent of breakage."

Jan 1, 2018

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014