Search Documents

By Anthony T. C. Goh

"For deep excavations in soft clay, it is common to use jet grouting piles (JGP) prior to excavation to minimize wall deflections and ground settlement, and to prevent basal heave instability. In this paper, finite element analyses were carried out to assess the basal heave factor of safety for excavations in soft clay supported by JGP. Comparison of the factor of safety from the finite element analyses with limit equilibrium methods was then performed. Subsequently, to account for the uncertainties in the soil and JGP properties, a simplified reliability analysis procedure is proposed to estimate the probability of basal heave failure for deep excavations supported by JGP.INTRODUCTIONJet grout piles (JGP) are often used to prevent basal heave instability and to minimize excessive wall and ground movements associated with deep excavations in soft clay deposits (Shirlaw 2003; Wen 2005; Ou 2006). The jet grouting process which is carried out prior to any excavation works produces a series of short overlapping grout columns resulting in a “continuous” base slab (commonly termed as jet grout pile or JGP) below the final excavation level that spans across the entire excavation (Gaba 1990; Hsieh et al. 2003; Ho and Hu 2006). Typically, the JGP thickness ranges from 2 m to 4 m.The focus of this paper is on the assessment of basal heave instability for deep excavations in clay stabilized with JGP. Finite element analyses were first conducted to determine the basal heave factor of safety for deep excavations in clay with JGP. Comparisons were then carried out with factors of safety based on conventional limit equilibrium methods. Since the conventional factor of safety approach does not explicitly reflect the uncertainties of the soil and JGP properties, it is demonstrated in this paper that a simple reliability based approach (Hasofer and Lind 1974) can be used to assess the probability of basal heave failure.LIMIT EQUILIBRIUM METHODFor excavations is clay, the Terzaghi (1943), Bjerrum and Eide (1956) and Eide et al. (1972) methods which are based on bearing capacity theory, are commonly used to determine the basal heave factor of safety. Another commonly adopted method in Japan and Taiwan is the slip circle method which involves taking moments about the lowest strut level (JSA 1988; Hsieh et al. 2008; Luo et al. 2012). The slip circle method has also been applied for excavations with a JGP at the base by incorporating the undrained shear strength of the JGP. In the slip circle method, the basal heave factor of safety FSslip is assessed by taking moments about the lowest strut level (Fig. 1)"

Jan 1, 1900

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Yuji Yamashita, Kazuyoshi Kamimura, Tsuyoshi Takahashi, Naoya Matayoshi

"The CDM-LODIC method (cement deep mixing - low displacement and control) method enables ground displacement to be reduced by removing an amount of soil equivalent to that of injected cement slurry and the volume of the plunged mixing tool, which causes a certain degree of ground displacement. Since the CDM-LODIC method was developed in 1985, it has been applied to over 930 sites and the accumulated volume of stabilized soil has now reached 7.6 million cubic meters.In the CDM method, the number of blade rotations per unit depth in the ground when the mixing blades are withdrawn is considered a construction item. The blade rotation number depends on the degree of mixing between the cement slurry and the ground Some field tests were performed based on the degree of mixing between the cement slurry and the ground. In these tests, a new concept of evaluating the blade rotation number when the screw rod penetrates to a given depth without injecting cement slurry has contributed to the degree of mixing. Furthermore, a correlation exists between the coefficient of efficiency of soil removal and the cement slurry admixture rate. In this paper, we discus the data collected in those field tests and present some application examples.OUTLINE OF CDM-LODIC METHODThe injection of cement slurry may cause some ground displacement during Cement Deep Mixing (CDM). In recent years, due to an increased demand for ground improvement work in urban areas, there is increased concern that buildings near any CDM site may be adversely affected. The deep mixing method which reduces displacement due to mixing (CDM-LODIC method) enables ground displacement to be minimized by removing an amount of soil equivalent to the injected cement slurry and the volume of the mixing tool, which itself causes some ground displacement. When the construction site is near other structures, regardless of whether on or under the ground, the CDM-LODIC method can be used in order to minimize any ground displacement. There are considered to be two main causes of ground displacement as shown in Figure 1. Displacement A indicates ground displacement caused by the volume of the inserted mixing tool during the penetration stage and displacement B indicates ground displacement caused by the volume of the injected stabilizing agent. Thus, by removing soil equivalent to the volume of the inserted mixing tool and the injected stabilizing agent, ground displacement can theoretically be minimized. Figure 2 shows the amount of observed ground displacement in the cases of CDM and CDM-LODIC at an actual site. These case studies indicate that ground displacement can be reduced by removing the soil."

Jan 1, 2015

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Sastry Putcha, Santosh Mummaneni, Avasarala Swamy

"Inspection of bored pile hole bottom prior to placement of concrete is one of the most crucial element of foundation design and construction, especially for end bearing piles. Pile hole bottoms that are not cleaned well for sediments could potentially result in settlement. Although many projects have specifications in-place for drilled pile hole inspection, they are rarely implemented as the current available tools are either unsafe or cumbersome and costly, thus making it very unattractive for owners and contractors. Further, sometimes the post-construction nondestructive quality control testing such as PIT or sonic logging on piles resulted in unanswered questions related to soft bottom. This generates costly disputes with additional testing including concrete coring and possible repairs. Currently, there are several bored pile bottom inspection devices in USA, namely, SID, DID, and SQUID which can either provide video and photo documentation or measure sediments.“ShaftCam”, a patented advanced Digital Borescope, was invented to address the issues related to pile hole bottom inspection with its ability to measure sediments as well as photo and video documentation. Shaftcam device consists of 8-inch diameter bell with a camera, led lights, air hose connection and penetrometer with digital measurement that are connected to a control power box and laptop through a cable. The bell is fitted with a round clear open fiberglass skirt to form an open chamber. A simple motorized winch frame allows the user to lower the ShaftCam equipment gently to the bottom of the shaft at the desired location. Once the bell with camera is lowered to the bottom of the hole, air is pumped into the clear chamber to displace the water/slurry/polymer and get a clear view of the hole bottom to record the conditions and measure the sediment thickness and resistance. The skirt can also be enclosed and lowered to the desired location to allow for inspection of shaft walls.ShaftCam weighs less than 15 lbs. (6.8 kgs) in water and allows for inspection of the hole by one person in less than 30 minutes. Use of ShaftCam has saved significant time and money and thus allowed owners and contractors to readily accept and implement the quality control measures in many projects in USA over past few years."

Jan 1, 1900

By Maurizio Siepi, Bruno Vingiani, Claudio Asioli

"The article describes an emergency rehabilitation intervention executed at Buyo Dam, in Ivory Coast, to intercept a significant water seepage occurring through the foundation of this zoned earthfill retaining structure constructed in the late Seventies. To solve the problem, a 800 mm thick, 400 m long impervious cut-off wall (COW) was constructed on the right side of the embankment, operating from the dam crest and with the reservoir almost at its maximum level. The use of an innovative pre-mixed self-hardening grout, with a target hydraulic conductivity coefficient (k) lower than 10-9 m/s, was considered the only way to match the tight working schedule and the strict requirements for the filling material of the COW.Presentation of the Hydroelectric Scheme of BuyoThe hydroelectric scheme of Buyo, located at 6°14’28” N 7°20’45 W on the Sassandra River, in Ivory Coast (Figure 1), was built in the late Seventies for agriculture and power generation. With a reservoir of 8.3 billion m3 and an installed power capacity of 165 MW, enough to supply electricity to 111,000 homes, it represents an installation of great significance for this West African country."

Jan 1, 2016

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Michael Arnold, Jignyash Manyam, Yoav Rappaport

The USACE required construction of over 13 miles of cutoff wall at an average depth of 65 feet for the Herbert Hoover Dike (HHD). To meet project requirements, to provide quality control and make sound operational decisions, automated data capture, retention and visualization is crucial. Accurate and complete data management allows the authors to deliver critical business insights and to improve operational efficiencies. The author’s understood the necessity of capturing all their data, and efficiently processing and displaying it for multiple stake holders, for both internal and external purposes. The authors realized early in the project life cycle that data ownership and management is one of the fundamental features of the construction process. The authors developed their own software and use two in house applications; WEB-BGM online portal and, b-project which store rig production information combined with field quality control. b-project is used to create and deliver the Enterprise Database (EDB) to the USACE. Another biproduct of capturing the production data is the generation of the Geographic Information Systems (GIS) and also business analytics visual interactive display, developed through Microsoft Power BI. The paper focuses on the business process workflow and various technologies employed and lessons learned from the field operator perspective to achieve higher returns on business software operations.

Oct 1, 2022

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

New York City is an urban environment with a history spanning over 200 years. The coastline of New York has changed over the years. In the East River, old bulkhead and remnant of relieving platforms together with variable bedrock elevations pose challenges in the design and construction of deep foundations. This paper presents a Case History of high capacity deep foundations along the Franklin D. Roosevelt (FDR) Drive on the Upper East Side in New York City. The project consists of a ramp that overpasses the FDR Drive allowing heavy trucks to access the Marine Transfer Station (MTS) facility built over the East River. Large diameter drilled shafts and mini-piles socketed to bedrock were designed and constructed. Remnant of old bulkhead was encountered at the site and a Ground Penetrating Radar (GPR) investigation was completed during the subsurface investigation phase of the design. This paper discusses details of the subsurface investigation program and design methodology of the high capacity drilled shafts and mini-piles. It also describes construction methods and results of Osterberg Load tests documenting the field values of skin friction through the rock socket. Other construction challenges include construction and drilling rock sockets for drilled shafts over sloping bedrock. 1. INTRODUCTION New York City is a renowned urban city that always calls for the most delicate, yet complex, and robust superstructures and most importantly substructure designs. The historic preservation of this large 200 years old city of 319 square miles is ever changing. Shorelines are often extended to accommodate new infrastructure and very often many miscellaneous structures are discovered below the ground surface. The East 91st Street Ramp was constructed to provide access to the East 91st Street Marine Transfer Station over FDR Drive and York Avenue. Another alternative ramp will be relocated to the South Bound (SD) of the FDR Drive at 92nd Street. A subsurface exploration program was completed in accordance with the New York City Department of Design and Construction (NYCDDC) general requirements, Section 4.5, to perform subsurface investigation along the FDR Drive in Manhattan, New York.

Jan 1, 2019

By Chiranjib Sarkar, Sibapriya Mukherjee, N Kumar Pichumani

With the rapid expansion of urban transportation systems, tunnels and cut & cover structures are considered as the only solution in improving the urban space congestion problem in mass rapid transit system. Therefore, it is necessary to accurately design underground structures with realistic assumptions and considerations of design parameters like site geotechnical data, water table, surcharge load etc. Over conservative approach provides not only uneconomical design but sometimes it also causes overdesign of the concerned structures. Water table depth has a significant role in some design aspects of underground structures like floatation check, lateral and uplift pressure on the buried structure, etc. In current practice of tunnel and cut & cover structure design, water table is assumed to coincide with the ground level. Most of the Design Basis Reports & Outline Design Specifications directly mention consideration of water table at ground level for floatation check and load calculations, etc. However, the actual scenario is different in most of the cities specially in northern, central, western and eastern regions of India except the coastal cities. In the present study an attempt has been made to carry out a parametric study on the effect of water table depth in the design of a typical 6.3m outer diameter circular tunnel with 6m backfill. In this study, it is also attempted to establish an analytical method of calculating the most realistic consideration of water table depth instead of the present hypothetical assumption of considering water table to coincide with the ground level. The findings of the current study may be helpful to the researchers and practising engineers in design of tunnel and cut & cover structure for subways and metros.

Nov 1, 2022

By Ronaldo Luna, Donald Deardorff

"The use of load and resistance factor design (LRFD) is well documented since the 1960s for structural applications when it was first adopted into the American Concrete Institute Building Code in 1963 and was established for geotechnical applications by the Danish Geotechnical Institute about the same time under the name of Limit State Design (LSD).The Federal Highway Administration required all federally funded projects to use the LRFD method by 2007. Due to this funding requirement, recent LRFD research for geotechnical applications has focused on common bridge foundations (i.e., driven or drilled shafts), resulting in good documentation for design using these methods. Unfortunately, the practicing geotechnical engineer does not intuitively know how to create resistance factors for deep foundations systems that have design methodologies and installation techniques significantly different from driven or drilled shaft foundation systems.Helical anchors typically use semiempirical methods for preliminary capacity design and a torque correlation methodology during installation to verify required capacity. Here we provide basic information on the LRFD methodology for helical anchor design. Additionally, the First- Order Second Moment (FOSM) method is applied to a previous helical anchor study (Hoyt and Clemence 1989) to determine resistance factors for an ultimate tension capacity strength limit state.MethodologyThe concept of the LRFD method is to establish factors for both the load and resistance that account for uncertainties using probability theory. The factors increase the nominal load and/or decrease the nominal resistance such that the probability of failure is an acceptable value. LRFD also accounts for the effects of load combinations (dead, live, seismic, wind, etc.) by determining the probability of the combined occurrence. The general form of the LRFD equation used by American Association of State Highway and Transportation Officials (AASHTO) is:"

Jan 1, 2009

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008