Search Documents

By R. L. Alexander

"Madawaska Mines Limited, incorporated in 1975 is the successor to Faraday Uranium Mines Limited. The history of the latter's mine development and corporate changes are outlined. This paper describes the geology of the Bancroft area and the rock types found in the mine, particularly the pegmatite which is the host rock for the uranium. The structure, mineralogy and distribution of the ore shoots are described with the method of grade control and mine development. The paper concludes with a summary of the production and mineral reserves.Location, Access, and PropertyMadawaska Mines Limited is located in Faraday Township, Hastings County, Ontario. The mine is in the N.T.S. quadrant 31 F/ 4, Bancroft sheet and near 46 degrees 01 minute latitude, 77 degrees 46 minutes longitude. The mine is one-half mile north of Highway 28, five miles (8 km) west of Bancroft, and is accessible by various highways from Toronto, Ottawa, Peterborough, and Belleville. (Fig. 1). A landing strip for small aircraft is located at the northwestern edge of Bancroft. Bancroft is a modern community with a population of 2,400. The company has the mineral rights to 2982 acres (1207 hectares) surrounding the mine workings and plant which are situated in the north parts of Lots 16 and 17, Concession XI, Faraday Township."

Jan 1, 1986

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

In this study, flotation of fine galena, chalcopyrite and pyrite was performed after grinding with different extent of oxidation-reduction condition adjusted by grinding media. Sodium dithionite and iron ions were added in mill to simulate pulp potentials and iron oxidation species produced by grinding media, respectively. The types and quantities of the metal oxidation species on mineral surfaces were determined by EDTA extractions, while the surface electrical properties of minerals and interaction of different types of metal oxidation species were studied by zeta potential measurements. It was found that the nature and concentration of the absorbed metal oxidation species were dependent on oxidation atmosphere controlled by the iron amount of grinding media. These species interacted with each other and had an important role in determining flotation of fine galena and chalcopyrite as well as activation of fine pyrite by lead and copper.

Jan 1, 2006

By Glenn Ferguson

BACKGROUND Metals Risk Assessment at Contaminated Sites ? The field of metals risk assessment has advanced rapidly over the last five years ? Significant uncertainties and data gaps remain that require additional research if accurate assessments are to be conducted ? Research is being conducted by regulators, external institutions and academia ? Risk assessment practitioners are in need of answers or solutions TODAY

Apr 1, 2005

By José Carlos Marques

This paper addresses recent calls to study the role of the state in private regulation. Using an historical, organizational-field approach, I trace and explain the evolution of public debates and interaction of different forms of regulatory initiatives dealing with Canada?s mining industry. The empirical evidence presented calls attention to the interaction amongst different regulatory forms, as well as the conditions under which the state will encourage fragmented initiatives, rather than facilitate and catalyze regulatory strengthening and consolidation. As such, my analysis: problematizes the underlying assumptions used as a starting point by the growing literature on the role of the state in private regulation; connects and juxtaposes recent scholarship to more established literature on regulatory state failure and self-regulation. I also contribute to the discussion on Canada?s CSR policy, outlining the likely regulatory effects of the current policy framework.

Aug 1, 2013

By H. Polkowska-Motrenko

Analytical methods for the determination of uranium and other precious elements in ores, industrial wastes and by-products have been developed. The analytical techniques employed are NAA and ICP-MS. Two procedures of digestion were applied: microwave acid digestion and alkali fusion. Accuracy was checked by using CRMs. Results of analysis of the same samples by the elaborated methods have been presented and compared. The methods will be used for estimating the capacity of uranium production for the Polish nuclear power programme.

Aug 1, 2010

By Peter Rubie

"For many years, optimising the relining of hard rock grinding mills has been complicated by:?? the large number of variables;?? the low frequency of relines (slow feedback loop);?? the potential economic risk associated with some changesA technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared.This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world’s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability.This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables.The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant."

Jan 1, 2012

The Buzwagi Project is owned by Barrick Gold Corporation and located in the Lake Victoria Goldfields of central Tanzania in the District of Kahama in the Region of Shinyanga. The property is 6 km Southeast of the town of Kahama, 3 km South and adjacent to the road between Nzega and Burundi. The Buzwagi property is 97 km South of Barrick?s Bulyanhulu Mine. There is access to the rail line which connects from Isaka to the Indian Ocean coastal ports of Dares Salaam and Tanga. The Feasibility Study and permitting were started in early 2006. Project Execution commenced in August 2007. Process Plant commissioning started in January 2009 and the first gold pour is scheduled for Q2 2009. The reserve has been established as 3.3M oz of gold plus 177M lbs of copper. The project has been developed to include a 30Mtpa Open Pit Mine and 4.4 Mtpa Process Plant. Over an expected 15 year mine life, Buzwagi is anticipated to produce approximately 3.02M oz of gold and 220,000 tonnes of copper concentrate. Infrastructure associated with the project includes a 107 km 220kV power line, site accommodation, water harvest and extensive security facilities. The project is expected to be built on budget and on time during a period of extreme market volatility. This paper reviews the initiatives taken to achieve community support, control cost escalation, maintain schedule and manage logistic challenges, plus ensure security and safety of all workers.

May 1, 2009

Partnership with MiHR ? AHRC and MIHR jointly developed Mastering Aboriginal Inclusion for Mining ? Customization specific to mining Mining is unique? ? History of Aboriginal peoples and the land ? Unique community needs ? Effects of Impact Benefit Agreements ? Remoteness of mines ? 1200 Aboriginal communities located w/in 200km of active mines or exploration ? Long term effects of the land

May 1, 2009

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009

By G. Labonté, J. Truskoski, A. Kerr, A. Bouchard, J. Barrett

"Improving mill grade recovery relationships is always good business. Inco’s Clarabelle mill has just undergone a $16 M process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Project team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as Inco embarks on its second century of operation. IntroductionIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at Inco’s Clarabelle mill in Copper Cliff, Ontario."

Jan 1, 2003

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By Nural Kuyucak, Graham A. Johnson

Noranda's Geco Division is presently developing a comprehensive reclamation plan for closure of its Manitouwadge, Ontario operation, expected late in 1995. As part of a program of progressive rehabilation, the existing 20 year old water treatment plant will be upgraded from a low density to a high density lime neutralization process treating AMD and excess site water. The process, developed by the Noranda Technology Centre, utilizes a two step rather than a single step process to bring the Ph to the required neutralization level, a variation which contributes to improved sludge properties such as higher density and decreased viscosity. This is of particular significance where sludge pumping or storage volumes may present a concerns.

Jan 1, 1995

The Millennium deposit, located in northern Saskatchewan between the McArthur River mine and the Key Lake mill, has considerable potential for becoming an operating mine. Located in the Athabasca Basin, Millennium is blessed with both the riches and the challenges that this basin offers. The potential for ground water inflows during shaft sinking, and the unconventional challenges associated with underground uranium mining, render the successful development of a new mine in this area especially rewarding. The preliminary design and engineering of the Millennium Project has tapped into the experience of other operations in the area, and has utilized new applications of geophysics technology to enhance the understanding of the local geological structure. This discussion will focus on the innovations, and the challenges specific to uranium mining, for a deposit that is poised to be one of the next mines to supplement Saskatchewan's uranium resources.

May 1, 2008

By A. J. Antony Chettupuzha

Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project as well as model project processes. Much of the information relating to processes and their structure, the actors that operate them, and the data associated with each instance of a process is encapsulated within workflows. The wealth of information contained in an EPPM system can be exploited to extract knowledge that can provide significant cost benefits to construction companies. Workflows provide an ideal medium for the capture of knowledge over the course of a project lifecycle. We demonstrate how this knowledge may then be used to analyze workflows and determine metrics that establish the suitability of workflows to construction processes. We present a conceptual approach to measure the performance of a workflow, its constituent components and evolution, which may be used to lay the foundation for establishing paragon workflows suited to classes of construction activities.

Aug 1, 2013

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By Paivi Suikkanen, Kari Hietala, Kaarlo Haavanlammi

"Processing of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of platinum group metals (PGM’s) and cobalt are key issues of the Nickel Smelting technologies. PGMs are typically found in association with each other, but also importantly with nickel and copper. A challenge of producing saleable concentrates at acceptable recovery degrees, an increasing focus on the sustainable use of metals and recent decreases in the value of nickel has increased the interest to find a reliable route from Cu-Ni-PGM bulk concentrates to product. According to studies, most efficient process for Ni-Cu-PGM concentrates is flash smelting using DON process20 years ago, in 1995, Outokumpu commenced at Harjavalta a new Nickel Flash Smelting technology based on the Direct Outotec Nickel (DON) Smelting Process. The DON process enables production of high-grade nickel matte with low Fe-content directly in the Flash Smelting Furnace (FSF) without subsequent converting. Metal values from the smelting slag are recovered in the Electric Furnace (EF) as iron containing Ni-matte. Matte refining is based on atmospheric pre-leaching and total pressure leaching. Nickel, cobalt and iron are leached leaving a leach residue containing small amount of gangue minerals and PGM’s. Iron is removed from the leach solution in and nickel will be recovered with standard methods. Overall > 95% metal recovery can be expected with low energy consumption and low environmental impact."

Jan 1, 2014

By N. Aydogan, H. Dundar, Å. Partapuoli, A. Fredriksson, P. Wikström, K. Tano, G. Adolfsson

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By H. Soto, J. Jara, F. Nava

A method has been developed to recover cyanide and copper from cyanidation effluents contaminated with thiocyanate and copper-cyanide complexes. Copper is precipitated as copper thiocyanate or as copper cyanide depending on pH and the concentrations of thiocyanate and cyanide present in the effluent. The copper precipitate presents good dewatering characteristics and can be easily separated from the effluent by thickening and filtration. The solution containing the bulk of the cyanide is then oxidized with ozone to transform the remaining thiocyanate into cyanide. This results in a regenerated solution rich in free cyanide that can be recycled to the cyanidation process. Careful control of the pH of the solution is required. First pH of the effluent is lowered to optimize the precipitation and oxidation stages, then the pH is restored to an alkaline value to regenerate the cyanide solution. Recoveries of over 96% copper are obtained. Free cyanide in the regenerated solution corresponds to up to 160% of the total cyanide contained in the original impure effluent. (The balance being accounted for by the cyanide obtained by the oxidation of thiocyanate). The efficiency of the thiocyanate oxidation stage is 85% to 90%. The method has been demonstrated at bench scale with effluents of various cyanidation plants of northern Quebec. A preliminary economic evaluation indicates that the procedure would be profitable for effluents rich in copper and thiocyanate. This is the case for most barren bleeds of Merrill Crowe and heap leaching operations and also certain CIP tailings of gold ores containing copper impurities. Environmentally the procedure is a better alternative than the current detoxification methods based on the oxidation of cyanide that do not allow for copper recovery and that have difficulties in producing a final effluent with acceptable levels of contaminants such as ammonia, thiocyanate and copper.

Jan 1, 1996

By Paul G. Dunn

Safe rapid drift development results principally in reducing exposure of underground workers to the working face. This reduction in exposure is not achieved until either the rock walls have been suitably scaled or sufficient support has been put in place. Rapid drifting enables quicker access to orebodies (increasing returns), higher production rates and a resultant lower cost of mining. The Mining Innovation, Rehabilitation And Applied Research Corporation (MIRARCO) has been developing technology and a methodology for safe rapid drift development within the underground metalliferous mining industry. In terms of rock scaling for underground metal mines, there is still considerable use of manual and mechanical impact rock scaling techniques. Two main issues result from this approach. The first is that in highly stressed or highly fractured ground, a decision has to be made as to when sufficient scaling has taken place. This is not always easy to do and hence operator judgment is a crucial element in this approach. During a baseline study of current rock scaling practices, a wide range of scaling practices were observed within five different underground mining operations; this demonstrates the difficulty inherent in the rock scaling quality decision making process. The second issue is related to the exposure of workers to freshly created rock surfaces. In manual scaling techniques this is unavoidable and despite the best scaling practices, accidents still occur. In an attempt to provide an alternative scaling technology, MIRARCO has been investigating highpressure water jet scaling for removing loose rock as part of the drift advance process. This technology not only provides a means by which scaling practices can be engineered (remove the loose material you want to in a given rock mass condition), it is also quicker and easily automated. Automating the scaling process removes workers from exposure to freshly created rock surfaces and also enhances the application of spray-on liners through improved adhesion of these support types to the rock surface. This paper describes the water jet scaling technology research and methodology for safe rapid drifting within the underground metaliferous mining industry and highlights the key issues and major drivers behind their continued development at MIRARCO.

May 1, 2004