Search Documents

By A. Singh

Deformation structures after tensile and compression tests on Mg926Zn64Y alloy extruded at 250°C and 400°C are studied, in as-extruded and heat treated conditions. The icosahedral phase particles stimulate recrystallization during extrusion, resulting in fine grain size. Tensile and compression tests at room temperature show comparable yield strength, with a yield asymmetry ratio up to 0.98. c-type dislocations are observed in the grains near the submicron size icosahedral phase particles. The source of these dislocations is believed to be dissociation of <c+a> type non-basal dislocations. No dislocation pile-ups on icosahedral phase particles are found. {10 1 2} type twinning occurs in compression.

Jan 1, 2006

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which &apos;bonanzas&apos; occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the &apos;indicator&apos; deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By W. Holyk

"Although lead, zinc, copper, and iron sulphides have been known for many years in the Bathurst region, the existence of large massive deposits was not known until the discovery of the Brunswick orebody in 1952. This was followed by the discoveries of the Anacon orebody in 1953 and the American Metals orebodies in 1954. There is no question as to the great importance of these large massive sulphide deposits, and no doubt that other sulphide deposits are to be found. The problem, of course, is where and how to find them.The discovery of the Brunswick and Anacon orebodies is attributed to geophysical work. The original discovery of the American Metals deposit is generally attributed to a regional airborne electromagnetic survey.It is generally stated that the Bathurst area is a geophysical camp, and this is essentially true, but in this highly competitive search for orebodies it is obviously impossible for an individual company to cover the entire area by a comprehensive geophysical survey. Some means other than geophysics must be used to narrow the target. The quickest, cheapest, and simplest method is geological investigations.It has been stated that nothing can be accomplished by geology in the Bathurst region, since the camp is largely covered with overburden. This is true only insofar as detailed work on certain properties is concerned. It is not true of the larger regional picture. Outcrops are scarce, but angular float is abundant, and precedent shows that angular float has moved but a short distance from its source.GeologyAeromagnetic maps published by the Department of Mines and Technical Surveys are the best guides to the geology and structure of the area. These maps supply factual information concerning the underlying rocks. When coupled with field investigations, they are very useful in the interpretation of regional geology and the selection of favourable areas. The discussion of the geology is accordingly centred upon the aeromagnetic maps. The following is essentially a working theory, based on geological facts as best reconciled with all other available information,"

Jan 1, 1949

By R. E. Dye

IF gold mining is to assume, or it might be better said to resume, a place of &apos; importance in the national economy of this country following the present war, then one must accept the thesis that gold will maintain the place it has for many generations held in the minds of men as a substantial and lasting emblem of material wealth-a metal in exchange for which men have always been ready to give up the possession of their worldly goods. The thought bas been advanced by some that gold is not necessary as a basis for exchange, that it has no real value anyway and, therefore, the world would wake up some morning to find that no one wanted gold and that, over night, its possession bad in some way ceased to be desired. Holding an equally extreme view there are those who advance the idea that, following the war, gold will in some mysterious way enjoy a fantastic increase in value. Neither of these extreme views can be successfully supported. To presume that by legislation or by general agreement gold would be or could be, over night, dethroned to the position of common stone is wholly beyond the realm of any possibility. The thought that this could come to pass is advanced by, and is attractive to, only those peoples who do not have gold and do r:ot have the means of producing it. To believe that the fundamental value of gold will suddenly change is likewise fantastic. I refer to the fundamental value, not the dollar price, of gold, for it cannot be denied that, with the colossal war expenditures now being made and with the huge national debts which are being piled up, there is a possibility, indeed per-haps a likelihood, that the dollar price .of gold may be revised upward. For the purpose of this discussion, however, that possibility is irrelevant and need not be considered.

Jan 1, 1943

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

Adaptive processing is often related to the mineral composition of the mining block currently processed. The portions of waste, ore and secondary product minerals considered are always positive and typically sum to 100% (i.e. a composition). A typical solution to predict block averages of spatially dependent quantities would be block kriging. However, kriging is based on spatial correlations and it has been repeatedly shown that correlations of compositional data are spurious and blurred by the constant sum constraint. Aitchison (1982) proposed a general solution for compositional problems, based on transforming the compositional data to a set of logarithms of ratios of components, and analysing the transformed scores. The transform is chosen to be invertible to ensure that no information is lost in the process. This methodology avoids spurious correlation problems and ensures coherence between results obtained with different subcompositions. Pawlowsky-Glahn and Olea (2004) adapted the approach for point-support geostatistics, allowing the prediction of point compositions from spatially neighbouring data, without the artefacts induced by standard multivariate cokriging. Unfortunately upscaling the results of this approach with block cokriging is not straightforward, because of the nonlinearity of logratio transforms. Furthermore, we have to consider those nonlinearities created by the dependence on the block composition of extraction efficiency and processing costs of the possible processing choices. This paper proposes a solution for predicting the conditional expectations of the benefit of processing the block with each processing choice using geostatistical simulations of the local values of the composition and the resulting block integrals. The computation for a large number of blocks can be done efficiently using Cholesky decomposition. The approach also allows the calculation of prediction errors for expected compositions and expected benefit at almost no additional computational cost. Such compositional approach is necessary, for example when processing choices depend on proportions of certain minerals after other components have been removed; or if processing alters the composition in a multiplicative way, by partially removing a portion of some components.

Aug 1, 2013

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By Philippe V. Scheers

Polycrystalline gold, glassy carbon and gold-activated glassy carbon electrodes were compared for the production of hydrogen peroxide by the cathodic reduction of dissolved oxygen. Gold was deposited on glassy carbon by sputtering with a sputter coater and by electrodeposition from a diluted KAuCl4 solution using short potential steps. The sputtered gold particles were not adherent enough, but there were no adhesion problems with the electrodeposited gold particles. The gold coverage of the glassy carbon surface could be varied by applying a different number of potential steps. The overpotential for the electroreduction of oxygen to hydrogen peroxide decreases with increasing gold coverage of the glassy carbon surface, and for gold coverages exceeding about 16 %, the overpotential is close to that observed on polycrystalline gold.

Oct 1, 2003

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By Jason A. McLennan

Conditional bias is an infamous problem with estimation methods including kriging. Changing estimation parameters will mitigate, but not remove, conditional bias. The conditional bias of kriging is well understood; however, there is widespread confusion in the literature and among practicing geostatisticians regarding the conditional bias of geostatistical simulation. There is no conditional bias of simulation when the simulation results are used correctly. The correct use of simulation for recoverable reserves estimation is to (1) generate multiple realizations conditional to all available data at a small scale, (2) linearly average all realizations to the chosen block size and (3) calculate the probability of each block being ore and the ore grade of each block. The ?probability of ore? and the ?ore grade? are conditionally nonbiased.

May 1, 2002

By Barbara Kirby

Mining Industry HR Challenges Mining industry needs to hire approx. 100,000 workers by 2020 Attraction and retention of talent in all occupations Mobility of skilled workers between mine sites 70 percent of employers expect labour shortages over the next 5 years. Largest shortages: -physical sciences and engineering occupations -trades and ?undesignated? occupations ?Undesignated? Occupations ?Undesignated? Occupations -eg. mill operators, production / development miners and heavy equipment operators More than 20,000 workers will be needed by 2020 in the undesignated occupations and another 11,500 tradespersons Turnover rate for trades and undesignated occupations at mines is high: 8.3% compared to 5.6 % for all other occupations There is no system to recognize the skills of high-demand undesignated occupations

May 1, 2010

By J-F. Magnan, M-A. Thibault, R. Boulianne, C. Gauthier, J-P. Gagné, G. Dufour

During the production of aluminium in smelters, the anodes used in electrolysis cells have to be replaced frequently. Anode butts are usually placed on anode trays for transportation and cooling, a practice during which Hydrogen Fluoride (HF) is emitted in large quantities. Covers developed in 2000 by Alcoa Deschambault to fit on the anodes trays were implemented, resulting in significant reductions of HF emissions. However, the covers are expensive to maintain and use short-life consumable parts. In January 2004, STAS and Alcoa decided to develop a more efficient design of cover, with lower maintenance costs and no need for consumable materials (like soft cushions). This paper presents a summary of the work performed to develop the new design as well as a summary of the test results.

Jan 1, 2006

By P. Gautier

Current feedstock in the aluminum hot forging processes can be used in the cast or extruded forms. The microstructural variation between as-cast and extruded materials could result in different mechanical properties and corrosion resistance for hot-forged products. Corrosion performances were examined for forged parts produced by two AA6082 feedstocks at different conditions using the following corrosion tests: open circuit potential, anodic polarization, salt spray exposure and corrosion fatigue. With the help of optical and scanning electron microscopes, metallographical investigations were carried out on cast-forged and extruded-forged materials before and after corrosion. The corrosion behavior of both materials was compared in both as-forged and aged tempers. Results show that there is no significant difference in the corrosion performance for final cast-forged and extruded-forged products.

Jan 1, 2011

By Andreea Catalina Gluhoi

Oxidation and reduction reactions of N-containing molecules have been studied over different types of gold-based catalysts, Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 (M, MI, MII=Li, Rb, Mg, Ce, Zr, Mn, Cu) prepared by deposition precipitation with urea. In general, all the catalysts were already active at low temperatures. NH3 oxidation was effectively catalyzed by Au/CuO/Al2O3, a catalyst which also gives the highest yield in N2. NO reduction by H2 performed over gold-based catalysts produced N2O, N2 and NH3 and N2O reduction resulted in the formation of dinitrogen. For all the reactions, large synergistic effects have been obtained by addition of different kind of additives.

Oct 1, 2003

By Chih-Huey Lin

The Au/?-Al2O3 catalyst prepared by AuCl3 impregnation is subjected to the influence of residual chlorine after an oven drying. A post-impregnation NH4OH treatment was able to eliminate chlorine, and to reduce the cluster size of Au moiety. However, the CO oxidation activity was not increased by this post-impregnation NH4OH treatment. This suggests that certain metal-support interaction (MSI) is the determining factor for the activity of Au catalysts. Thermal treatment under H2, O2 or He was attempted to increase MSI of the prepared catalyst with or without the post-impregnation NH4OH treatment. No significant activity enhancement was found but the TPD analysis suggests that a H2 treatment has a higher chance to induce MSI.

Oct 1, 2003

By Marcotte P.

Introduction Pneumatic jackleg rock drills are commonly used in underground mining operations. These tools are known to expose their operators to hand-arm vibration levels in the order of 20-35 m/s2 weighted (Wh). Thus, the majority of the workers who have cumulated several years of jackleg rock drill operation are affected by related health problems such as Raynaud&apos;s syndrome or carpal tunnel syndrome. Up to now, no efficient personal safety device was available to protect pneumatic rock drill operators against hand-arm vibration (HAV). To address this problem, an anti-vibration handle prototype for jackleg drills has been developed in a previous study. Then, a multi-partner project was launched to refine the prototype and commercialize an effective anti-vibration handle for pneumatic rock drills.

Feb 1, 2008

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By W. Dan Hausel

"Abstract-Hundreds of diamonds have been found in the United States. The majority of the discoveries occurred during the 19th century as a by-product of placer gold mining. Most of these early diamond finds have no known source, and in many cases are situated in areas unfavorable for diamond exploration based on current models that require kimberlite or lamproite to be emplaced in a stable Archean craton or Proterozoic craton margin.Diamonds have also been recovered in situ from lamproite at Murfreesburo, Arkansas, from kimberlite in the Lake Ellen region of Michigan, and in several kimberlites in the Colorado-Wyoming State Line district. Unverified reports also suggest that diamonds may have been recovered from other related intrusions at a number of localities in the United States."

Jan 1, 1995

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014