Search Documents

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By V. Songmene, R. Khettabi, J. Masounave, R. D. Njoya

L'augmentation régulière des règlements environnementaux et de la sécurité au travail deviennent de plus en plus strictes. L'usinage fait partie des opérations industrielles qui peuvent causer des problèmes de santé au travail et sur l'environnement. La plupart des particules de poussières produites pendant toutes les opérations d'usinage à sec ou lubrifie causent des nuisances environnementales graves. Le travail propose étudie l’influence des paramètres de coupe, des alliages et des états des matériaux sur la formation des copeaux et sur la génération de poussière lors de l'usinage à sec. Deux modes d'usinage (le fraisage et le perçage) sont abordés. Une loi reliant la ténacité des matériaux aux émissions de poussières est proposée. Les effets des matériaux et de leurs conditions, ainsi que des procédés d'usinage sur la génération des poussières ont été mis en évidence. Des mécanismes de formation de poussières sont identifiés et reliés à la formation des copeaux.

Jan 1, 2006

By W. Dresler

"A major Canadian chromite deposit at Bird River, Manitoba is one of the largest known chromite reserves in North America but it exhibits low chromium contents and low chromium to iron ratios. Commercial beneficiation techniques permit these ores to be upgraded to concentrations which, however, remain inferior to most other ores and concentrates used worldwide f or production of high-carbon ferrochromium. Analyses for reduction of low-grade concentrates by submerged-arc electrofurnace techniques predict chromium contents between 45.9% and 51% for a high-carbon ferrochromium alloy. Relatively high over-all chromium recoveries between 79.5% and 91. 1% can be achieved. Alloy compositions for Cr, Fe, C and Si are determined for various burdens with low-grade concentrates. Consumption data per ton contained chromium are obtained for electric power, coke, concentrate, quartzite and limestone. The data are compared with those of high-carbon ferrochromium producers in South Africa. Economic aspects are discussed and compared with a South African reference study.IntroductionThe present ferrochromium demand in the western world is estimated at approximately 1.7 Mt with a consumption of approximately 0.36 Mt in the U.S.III and 0.03 Mt in Canada'-', A low estimate of the installed production capacity for ferrochromium in the non -communist world is 2.4 Mt. This production capacity of ferrochromium by far exceeds the demand, which is also evident from the fact that no shortage in supply of ferrochromium to the world markets was encountered in the past. Supply-demand comparisons therefore suggest that in the foreseeable future no new chromite or chromium producers should enter the world markets unless superior chromites or superior technologies are successful in competing with existing producers. Neither one of these conditions exist presently in Ca nada or the U.S., although essentially no ferrochromium is produced and no chromite is mined in these countries at the present time."

Jan 1, 1986

By Roy EI. Durr, Glen R. Davidge

"This paper presents the results of structural analyses and full-scale destructive tests conducted on liner plate culverts. The purpose of this work was to establish a design method and evaluate the suitability of using these structures in potential roof-fall areas for a rehabilitation application in lower stress and relaxed mining environments. Field evaluation of the design is currently in progress.Theoretical ultimate resistance functions were established for two different culvert shapes and were found to be representative of their experimental behaviour. The ultimate resistance function was used to determine their plastic behaviour to a rapidly increasing deflection condition, to determine the energy absorption capacity of these structures, and to predict their response to impact loading.IntroductionThe Kidd Creek mine of Falconbridge Limited is located justnorth of Timmins, Ontario. The area under rehabilitation for which this program was developed is the 2600 level of the No. I mine. The problem of effectively securing selected drifts at the 2600 level in NO.1 mine, for access to a high-grade ore block, is key to the economics of the operation. Diamond drill test holes had indicated a loosened rock mass above the 2600 level of about 7.5 m thick in response to the extensive mining operation below this level. This level forms the arbitrary boundary between the No. I and No. 2 mines, and has extensive volumes of cemented rock fill below it and largely untouched ore above it to the 2000 level in the North orebody. The walls at that level were showing relaxed ground conditions typical of de-stress: sub-horizontal joints opening up, and peeling.Due to the ground conditions, the consequent safety risks, the high grade of the ore, the potential production delays, and the likelihood of several phases of rehabilitation, regularly used drift rehabilitation employing rock bolts, cable bolting, or shotcrete was not practical. Two options were deemed possible alternatives to suit these conditions, steel sets with blocking and lagging, and liner plate culverts with backfill. Culverts were chosen."

Jan 1, 1995

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By Antonio Fontana

"Environmental problems encountered with the use of diesel equipment in underground mining operations are discussed. The concept and procedure o implementing the Health Effects Index equation as a means of quantitatively assessing an underground working environment is outlined and sample calculations are present ed. Advantages and disadvantages of utilizing this method are also discussed.IntroductionWith the introduction of diesel-powered mining equipment in the 1960s there arose several question s for the environmental engineer to consider. These included: 1. What are the constituents of diesel exhaust and how can they be detected and evaluated?2. What are the toxicities and long-term health effects of these constituents?3. What is the ventilating volume required to maintain the concentration of these constituents below toxic levels?Diesel engines are a class of reciprocating, internal combustion engines in which relatively high compression ratios are used to generate high air-charge temperatures, which cause ignition of fuel to occur spontaneously. Ideally, perfect combustion of the fuel would produce an exhaust consisting solely of nitrogen (N2), water (H2O), carbon dioxide (CO2) and oxygen (O2). However, because no combustion process is perfect, relatively small quantities of imperfect-combustion products, or pollutants, are also generated. These include hydrocarbons (HC), carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), carbon (C) or soot, and sulphur dioxide (SO2).Currently, the Regulations for Mines and Mining Plants, made under the Occupational Health and Safety Act (Section 176), stipulate that weekly tests shall be made to determine the carbon monoxide (CO) concentration in the undiluted exhaust and at the operator's position, and the nitrogent dioxide (NO2) concentration at the operator's position. Also, the aldehyde (as HCHO) concentration in the atmosphere, at the operator's position, is to be measured at least every three months. Threshold limit values (TLVs) have been established for each of the three combustion products, and each is regarded as a separate entity. Consequently, this does not allow for consideration of interactions and possible synergistic effects between the various exhaust components."

Jan 1, 1982

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By W. McCombe, G. Remple, L. Nightingale-Mercer

The McClean Lake Mill is located approximately 850 kilometres north of Saskatoon, Saskatchewan, Canada, and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and a multi-year expansion was completed in 2014 to increase its production capacity to 24 Mlbs U3O8 per annum. The mill also underwent various upgrades to allow it to safely transition from processing low grade ores to high grade ores from the nearby Cigar Lake Mine. During the metallurgical test work on the Cigar Lake ores, it was identified that some ore zones of the deposit have a propensity to generate hydrogen gas during acid leaching. Hydrogen is a volatile and explosive gas, which poses obvious safety concerns in the leaching circuit. Uranium processing is further complicated by the fact that an oxidant in the form of oxygen gas or hydrogen peroxide is required to regenerate iron in the leach, which further increases the risk posed by hydrogen gas. During 2013 Orano and its consultant Hatch designed and engineered several novel upgrades to the leaching circuit to mitigate the risk of hydrogen gas evolution in the process. Best in class technology was utilized in addition to control and operating strategy changes to ensure the leaching circuit could be safely operated with ores that evolve hydrogen gas. This paper reviews the design concepts and modifications implemented on this unique and challenging project, and also provides an update on the operational reality of hydrogen in the circuit gained through five years of operational experience with hydrogen evolving ores.

Jan 1, 2020

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

By E. Krause, V. G. Papangelakis, S. Garg, R. Mahadevan, E. Edwards

"Bioleaching uses iron and sulfur-oxidizing bacteria to extract base metals from sulfide minerals. As bioleaching involves breaking the iron-sulfur bonds by ferric attack, the biologically mediated rate of iron oxidation is recognized to play a key role in influencing the overall kinetics. In this study, we investigate the catalytic ability of an indigenous AMD culture for oxidizing Fe(II) in solution. This culture was subsequently adapted on pyrrhotite tailings (0.6% Ni) by gradually increasing the solids loading. Results from this study show that such an adaptation reduces the initial lag phase in the biotic oxidation of Fe(II), thereby allowing for a higher Ni extraction when compared to experiments with an un-adapted culture at a similar solids loading. The use of adapted cultures also helps to reduce the residence time for bioleaching of Ni from pyrrhotite tailings. INTRODUCTIONAs the world demand for pure base metals grows; the mining industry is increasingly faced with the burden of processing lower grade ores and mining waste streams in order to recover the occluded metal VALUES ((Watling, 2006). The extractive metallurgy of nickel from sulfide minerals focuses on using a combination of mineral processing, pyrometallurgical (smelting) and hydrometallurgical techniques to extract Ni from its ore bodies.Pyrrhotite (Fe1-xS) is commonly found in association with pentlandite and chalcopyrite in sulfidic Ni ores, such as those found in Sudbury, Ontario, and in Russia, e.g. Norilsk. The vast majority of this pyrrhotite needs to be removed using mineral processing techniques, in order to minimize the Fe and S contents of the concentrates that proceed on to smelting. If all pyrrhotite were left in the concentrate, much more slag and SO2 would be produced, and the smelter throughput would be limited. Beneficiation of Ni sulfide ores leads to the rejection of unwanted constituents as mining wastes, which may still contain extractable amounts of Ni (Edgar Peek et al., 2010)."

Jan 1, 2012

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By S. Nikolic, H. M. Henao

"There is renewed interest in the improvement of existing copper smelting processes and the development of new technologies. It has become clear that further accurate information on slag properties, in particular, on phase equilibria are required in order to optimize these processes. It is in this context that improved experimental research methodologies have been developed specifically to provide information on phase equilibria at the oxygen partial pressures encountered in copper smelting practice. The methodology involves synthetic slag equilibration at controlled gas atmospheres, quenching and measurement of compositions of phases with an electron probe X-ray microanalyser (EPMA) with wavelength dispersive detectors (WDD). Application of modem analytical tools and careful design of experiments greatly improve accuracy of determination of phase equilibria in complex, multi-phase slag systems. New experimental data on phase equilibria for the copper smelting and converting silicate slags at controlled oxygen partial pressures in the temperature range between 1200°C and 1350°C in the ""Fe0""-Ca0-SiO2 system and in the ""Cu20""-""Fe0""-Ca0-Si02 system in equilibrium with metallic copper are reported, and differences between various data sources are analyzed."

Jan 1, 2007

By A. Ehsani

"Seas and oceans constitute about 70% of the earth’s surface. They contain an enormous stock of various mineral resources such as sedimentary (marine placers), massive sulfide ore deposits, manganese nodules and cobalt-rich ferromanganese crusts. Sea and ocean floor ore deposits could well contribute to the meeting of ever-rising demand for raw materials in the metal industry. In this regard, more research and development in science and technology appear to be required to ensure maximum benefit from the mineral resources of seas and oceans. Since the 1960s, a variety of mineral and metallurgical processes have been studied and developed to deal with marine ores and to extract metals such as gold, nickel, copper, cobalt, manganese, tin, platinum group metals (PGM), zirconium, thorium, etc.In marine environments, there are many parameters which can affect the selection of the mineral and metallurgical processes. These include the extent and grade of the deposit, mineralogical and chemical properties of the deposit, and physical properties of minerals present with particular reference to particle size distribution and mineral liberation size.In this paper, we briefly review the latest trends in processing and extraction of marine mineral resources. Mineral processing technology is mostly applied for recovery of precious metals i.e. gold and PGM, in particular, from marine placers. In general, pre-treatment (sizing, classification, dewatering), gravity concentration techniques (shaking tables, spirals, jigs, etc.,), flotation, magnetic, and electrostatic separation are the options for enrichment of marine placer ore deposits. In the case of massive sulfides, manganese nodules/cobalt-rich crusts, hydrometallurgical and pyrometallurgical methods (as proven technological methods) can be exploited for extraction of metals from concentrates after physical separation or directly from marine ores. The hydrometallurgical treatments involve acid (e.g., sulfurichydrochloric) and alkaline (e.g., ammonia) leaching with different reducing agents and pre-treatments such as roasting. Alternatively, pyrometallurgical treatments involve mostly smelting, chlorination and segregation processes."

Jan 1, 2016