Search Documents

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By C. A. Jeffrey, K. Pearson

Abstract - The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the overlying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release of volatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of lowtemperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehnite and pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, during post-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystalline calcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from fluid inclusion work indicates that two fluids were involved in the deposition of the zeolite veins. One fluid was initially of relatively high temperature (~100°C to 320°C) and low salinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other was of relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.), and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat flow, initiating the circulation of hydrothermal fluids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Jurassic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By C. A. Jeffrey, K. Pearson

The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the over-lying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release ofvolatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of low-temperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehniteand pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, duringpost-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystallinecalcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from ?uid inclusion work indicates that two ?uids were involved in the deposition of the zeolite veins. One ?uid was initially of relatively high temperature (~100°C to 320°C) and lowsalinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other wasof relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.),and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat ?ow, initiating the circulation of hydrothermal ?uids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Juras-sic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By T. Hofbauer, M. J. Dry, G. B. Harris, C. W. White

"Urban Mining is a term that is increasingly being used, and represents an appreciable source of secondary materials for the metals extraction industry, a source that does not incur mining costs, but does, at present, incur considerable disposal costs. Electric Arc Furnace Dust (EAFD) is probably the most common of these materials, with an estimated global production of 8 million tonnes annually, of which 1 million tonnes is generated in North America. The contained annual metal value in EAFD at current prices is of the order of $6 billion, yet, apart from the zinc, virtually none of this is recovered.Despite many attempts over the years, with pyrometallurgical, hydrometallurgical or hybrid processes, currently the only commercially viable method of treating these materials is smelting in a Waelz Kiln (or a Rotary Hearth Furnace), which essentially recovers only the zinc, in an impure oxide form, and generates a secondary slag waste, which is still toxic and requires disposal. This paper describes the development of a chloride-based treatment process to recover all components of the EAFD in a marketable form, which centres around the novel hydrochloric acid recovery and recycle operation. Laboratory, miniplant and pilot plant data are presented, leading to the definition of a viable process flowsheet enabling the recovery of pure iron and zinc products (the principal components of EAFD), together with secondary products such as copper, silver, lead, cadmium, magnesium and manganese. A rigorous mass-energy balance is used to examine the preliminary economics involved."

Jan 1, 2014

By N. T. Oo, L. D. Hutton

"The Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. A site specific rock classification system was developed that characterised all the rock units based on the engineering properties governing the rock mass behaviour i.e. intact rock strength and defect characteristics (spacing, aperture, infilling, wall roughness and weathering) irrespective of the geological origin. This approach simplified the design and the on-site verification processes. Based on this classification system, rigorous quantitative statistical assessments of the available geological information including various laboratory and field testing were performed to derive the geotechnical design parameters for various rock classes. These parameters were used to complete geotechnical designs of retaining wall systems. INTRODUCTIONThe Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The key features include two interchanges, a 300m long viaduct, a large cutting through Sexton Hill with an associated 100m wide Land Bridge and retaining walls reaching 490m long and up to 22m high. This paper focuses on the derivation of representative geotechnical parameters for geotechnical design of the retaining structures supporting Sexton Hill Cutting including bored pile retaining walls and soil nail walls. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. Due to the complex geological nature of the site, an understanding of the regional and local geology, the typical behaviour of individual geological units and the implication of onsite variations from design intention are the ultimate challenges to the geotechnical engineer in order to select representative geotechnical parameters for design."

Jan 1, 2015

By Victor F. Hollister

Elemental sulphur occurs as aformational sedimentary deposit in Upper Devonian Wabamun evaporites near Coronation, Alberta. The deposit developed in a stratigraphic jacies-change lrap; it is assumed that petroleum reacted with anhydrite to form sulphur, calcite, hydrogen sulphide and other reaction products. The deposit contains about 362,800 tonnes of sulphur and lies at a depth of 1200 m. The Coronation deposit is expected to be geologically typical of such other native sulphur deposits as may be found in Wabamun Group sediments. Widespread sour gas sulphur production f rom the Wabamun suggests the possibility that additional native sulphur deposits will ·be found.

Jan 1, 1984

By Denis Yaychuk, Gary Billingsley

The economic eva luation of a mineral property or mining venture should include the quantification of ri k as part of the analy is. The re ults of such an analysis provide the decision-makers not only with the most likely financial outcome and the probability of achieving that or any other outcome. but al o with a ranki ng of the relative impact of all the ri sk factors. These type of resu lts offer more complete information for investment and technical deci ions than the traditional cash flow/ ensitivity analysis. In addi tion. by attempting to quantify ri sk. the personnel providing the va ri able input are forced to take a much clo e r look at the data involved, and are fo rced to work together. the reby increa ing substantially the awa reness of the impact their work and others· work has on th e outcome of the analysis.

Jan 1, 1986

By C. Karpuz, Y. S. Istanbulluoglu

This paper describes the results of convergence measurements conducted about five years for the re-use gate roadways at OAL lignite mine in Turkey. Double lignite seams separated with a marn layer, are mined with long-wall retreating mining system at the mine. Rib pillar has been abandoned and gate roadways were planned to be packed for the re-use of full extraction. Various packing systems have been attempted, namely three rows of woodenchock, one row of wooden chock plus concrete wall and concrete wall only. The re-use of maingate roadways packed with wooden chock yielded 62% of closure. Lastly developed concrete packing of 3 meters wide and specially developed support set composed of three friction props and a cap, which is a modification of yieldable set, have successfully maintained the main and tail gate roadways stability with a total vertical convergence of 32%. Good correlation has been established between pack stiffness and floor heave as well as maingate and tailgate convergences. The elimination of rib pillars by re-use of gate roadways increased the coal recovery by 20% and decreased the development/production ratio from 0.065 m3/ton to0.022 m3/ton.

Jan 1, 1997

By T. H. Chuang, Y. Y. Shiue

"Rapid whisker growth was significantly alleviated in a Sn-58Bi alloy doped with 0.5 wt.% La. Experimental results showed that many thin, plate-form intermetallic phases appeared in the solder matrix. The absence of tin whiskers was correlated to the shape effect of RE-containing intermetallic plates. After reflowing, Cu6Sn5 intermetallic compounds appeared at the solder/pad interfaces of Sn-58Bi and Sn-58Bi- 0.5La packages with OSP pads, which grow linearly during the aging at 75 and 100? for various times ranging from 100 to 1000 h. In addition, the interfacial intermetallics layers in Sn-58Bi-0.5La solder joints were also observed thinner than those in undoped Sn-58Bi joints. However, RE-containing interfacial intermetallic compounds in Sn-58Bi-0.5La solder joints led to lower bonding strengths in both ball shear tests (0.4 mm/s) and high speed ball shear tests (2000 mm/s). All the reflowed and aged solder joints of both packages were ruptured through the solder balls indicating brittle characteristic INTRODUCTIONIt has been widely reported that solder alloys doped with rare earth (RE) elements reveal many beneficial effects, such as higher strength, lower melting point, improved wettability, and longer creep life (Wu et al., 2004; Ma et al., 2002; Chen et al., 2002). In addition, Dudek et al. reported that the alloying with 0.5 wt.% La in Sn-3.8Ag-0.7Cu solders resulted in an increase of rupture strain, up to 150% over undoped solders (Dudek et al., 2006). However, Chuang and Yen observed that a large amount of long, fiber-shaped tin whiskers were extruded out of the oxidized CeSn3 intermetallic clusters in the matrix of a Sn-3Ag-0.5Cu-0.5Ce solder air-stored at room temperature for several days (Chuang & Yen, 2006). Furthermore, many coarse hillocks appeared around the CeSn3 clusters in the RE-doped alloy after storage in an air furnace at 150? for several minutes. Chuang proposed a mechanism for the phenomenon of rapid whisker growth, which the predominate oxidation of CeSn3 intermetallics in Sn-3Ag-0.5Cu-0.5Ce solders induced compressive stress and extruded the tin atoms out of the specimen in the form of tin whiskers (Chuang, 2007). However, further investigation showed that Sn-9Zn-0.5Ce solders, after long term exposure at room temperature and 150?, were immune to the whisker growth; the immunity was attributed to the refining of the CeSn3 intermetallic phase in the alloy (Chuang & Lin, 2008). The inhibition of tin whiskers through the refining of rare earth containing intermetallics was further observed in Sn-3Ag- 0.5Cu-0.5Ce solders doped with 0.5 wt. Zn (Chuang & Lin, 2009). In addition to the size effect, the thin plate shape of intermetallic compounds was also shown in this study to inhibit the whisker growth on the surface of Sn-58Bi-0.5La solders."

Jan 1, 2012

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By P. R. Geoffroy

Extensive and Intensive Prospecting As often pointed out, the search for new ore deposits may be carried on along two widely divergent lines. It may be either extensive or intensive. By extensive prospecting we mean a search for mineralized outcrops conducted over large and more or less virgin tracts of land, followed by a test of the practical value of any discovery made, the test being limited to the immediate vicinity of the outcrop. Extensive prospecting, was, in fact, the only policy known to the early prospectors. of the American continent and is still the rule in the remote sections of the Canadian Shield and in the African wilderness. It can be further characterized by the lack of emphasis placed on geological and other technical means as an aid to the search for ore. However, very little virgin ground is left, nowadays, for a man or a company to test their luck, and whatever is left is so remote from the necessary means of development that any new discovery will require considerable delay and expenditures to be amenable to profitable mining. On the other band, a great many of the favourable and still unexplored areas (and this is particularly true in Canada) are overburdened to such an extent that outcrops of bed-rock are extremely scarce and extensive prospecting is nearly impossible. Intensive prospecting, to the contrary, must be understood as a detailed search for ore carried on over limited areas in districts already known to be mineralized and covering regional structures whose relation to mineral deposits bas been estahlis.hed with a fair degree ot certainty. The search for deep-seated deposits in the vicinity of successful mines is a perfect example of intensive prospecting. As a matter of fact, the majority of the geologists employed by the mining industry are engaged in some kind of intensive prospecting.

Jan 1, 1950

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By A. O. Dufresne

Introductory At the Annual Meeting of the Institute, held two years ago, I had the privilege of presenting a paper on Recent Mineral Discoveries in Western Quebec. In it were pointed out the areas favourable for prospecting in that section of Quebec adjoining the mining camps of northern Ontario; the discoveries that ?had been made were recorded; and some of the developments up to that date were reviewed. Since then, two full years have elapsed, during which a considerable amount of serious work has been performed with such results that western Quebec has today six properties about ready to mine commercial ores of gold, copper, and zinc. These results have been brought about after large sums of money had been invested to bring the district to a producing stage. A smelter has been built, and is already producing copper; two railways have extended their lines into Rouyn; and the Provincial Government has shown faith in the future of the district and has spent large sums of money in the building of highways and for other public works. The purpose of the present paper is to review the developments of the last two years, and the work that has been performed in various spheres of activity in that section on western Quebec covering the county of Abitibi and the northern part of the county of Temiscamingue.

Jan 1, 1928

By R. M. Young

In. East Kootenay, two Companies are operating, the Crow's Nest Pass Coal Company of Fernie, with mines at Coal Creek and Michel, and the Corbin Coal and Coke Company, of Corbin and Spokane. Wash., with mines at Corbin. The Crow's Nest Pass Coal Company has also coke-ovens of the bee-hive type at Fernie and Michel. The mines have a productive capacity, with present development and plant, of approximately 1,500,000 tons of coal, and of 300,000 tons of coke annually. The total production in 1923 was 828, 990 tons of coal and 65.990 tons of coke. In the early years of operation, the mines furnished a very large percentage of their output to the railways and smelters. These were, in fact, the primary markets for which the mines were opened and the ovens constructed. The Great Northern Railway had built into Femie, and later extending its line to Michel, became a heavy consumer of both of these mines. The Spokane International, connecting the Crow's Nest branch of the C.P .R. with Spokane, furnished tonnage to Corbin. The Canadian Pacific Railway bought for Crow's Nest consumption. The smelters at Grand Forks and Trail in the Boundary country were large and steady consumers of coke, while in-termittently Northport, Butte, Helena, and Great Falls shared in the product of the ovens.

Jan 1, 1924

By Malcolm Scoble, Nick Vagenas, Greg Baiden

Recent advances in underground communications technology have demonstrated the feasibility of teleoperation and automation in underground metal mines. One major challenge lies in the automation of underground mobile machines from surface, with the potential to reduce significantly the need for human involvement in underground operations. This paper reviews the evolution of underground metal mining automation, principally related to the development of teleoperation and automation of mobile mining machines. Examples of prototype systems are given and the associated benefits that have been observed are reviewed.

Jan 1, 1997

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By Robert A. MacGregor

"Following several months of test work, water leaching in mined-out areas at Stanrock commenced on a production basis in February, 1963. A combination of fast high-pres-sure washing and rewashing of stopes on a predetermined cycle, and the intermittent sprinkling of low-grade heaps, using both fresh water and recirculated acid water, has proved most successful. There was also a correlation of daily sampling data points to a relationship between the leach water grade and the grade of the material being washed, the leaching time and the location along the dip. An increasing tolerance for uranium by the acid-producing bacteria is also indicated. A steady production rate of 10,000 to 12,000 lbs. of u.08 per month is being maintained, with an over-all mine water grade of 0.25 lb. per ton and a pH of 2.3."

Jan 1, 1966

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925