Search Documents

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,' P. H. Keck,' and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,' the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O'Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie' has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10' cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.' This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.'-= At the same time, the material shows considerable ductility.3'4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin's relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1' presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.'3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella's reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With' elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By I. J. Hegyi, J. J. Tietjen, H. Nelson, J. I. Pankove

The fabrication of p-n junctions in GaAsl-,P, alloys by a vapor-phase gowth technique has for the first tirne resulted in room-temperature injection lasers capable of operating over a broad range of wavelengths extending into the visible region of the spectrum. The shortest wavelength achieved to date is 6750A at room tetnperature. In addition, at 78°K the threshold current density values for these lasers are generally the lo~vest reported, and the emitted radiation extends to the lozc,est wavelength ever attained (6350A). With lasers fabricated from material containing 14 pct Gap, quanticm efficiencies of 26 pct and peak power outputs of 25 zu were obtained at room temperature. ALTHOUGH room-temperature operation of GaAs injection lasers has been well-documented,&apos;-5 the operation of GaAsl-,P, (x > 0) laser diodes has been restricted to relatively low temperatures.8-&apos;0 This has been previously attributed5, 7, 10-12 partially to the difficulty of preparing single-crystalline GaAsl-& alloys having a high degree of chemical homogeneity and purity. Also, with these materials it has been difficult to prepare high-quality, abrupt p-12 junctions by diffusion techniques; and, in turn, this has made it difficult to obtain optimum electrical properties for room-temperature operationL3 in the resulting laser diodes. As a result, GaAsl-,P, laser diodes have not been efficient enough to permit operation at room temperature. For example, using diffused structures, only a few diodes were obtained which could be operated even close to room temperature (255K)." Recently, a vapor-phase growth method of preparing epitaxial deposits of GaAsl - .P, alloys has been described,14 and the high-purity and homogeneity of these materials has been previously demonstrated. Of special significance, with this technique, n- or p -type doping can be initiated or discontinued at any time and at almost any rate during the crystal growth so that the donor and the acceptor concentrations can be easily controlled to obtain desired impurity profiles. This permits high-quality, abrupt p-TZ junctions to be vapor-phase grown entirely during the crystal growth process, so that diffusion or other p-n junction fabrication processes are unnecessary. After growth, the device does not have to be heated to elevated temperatures, which avoids the possible unwanted introduction and motion of both impurities and lattice defects. Using the vapor-phase growth method cited above, over 300 room-temperature injection lasers have been prepared from GaAsl-,P, alloys having compositions in the range of 0 5 x 5 0.41. These lasers have emitted cohe~ent radiation in the spectral range of 8350 to 6350A at 78°K or from 9000 to 6750A at room temperature. The threshold current densities of the best lasers are independent of the alloy composition over the range 0 < x < 0.2 and compare favorably with values for good GaAs lasers.&apos; MATERIAL PREPARATION Multilayer, epitaxial deposits of GaAsl-,P, alloys are prepared by a vapor-growth technique described elsewhere.14 With this technique, the individual layers which comprise the multilayer structure are prepared sequentially in the deposition apparatus without interrupting the crystal growth. The epitaxial layers are deposited on GaAs substrate surfaces oriented normal to the ( 100) direction. The substrate wafers employed in this study were usually doped with tellurium to an electron concentration of approximately 2 x 10" per cu cm. To avoid strains, the first 10 to 15 p of the deposited material is uniformly graded from pure GaAs to the specific GaAsl- ,P, alloy composition of interest. The GaAsl - ,P, alloy growth is then continued to form a layer of constant composition having a thickness in the range of 25 to 75 p. Both the graded region and the layer of constant composition are doped with selenium to an electron concentration of about 2 x 10" per cu cm. The p region of the diode is then incorporated in the crystal by abruptly changing the dopant concentrations in the vapor phase to facilitate doping with zinc. This layer has a hole concentration of approximately 3 X 1019 per cu cm and typically is 50 p thick. DEVICE FABRICATION In general, the GaAs substrate and the region of graded composition are removed. Ohmic contacts are made to the n-type side by tin evaporation and to the p-type side by an electrodeless nickel deposition. This is followed by an electrodeless deposition of gold on both sides. The crystal wafer is then cleaved along (110) planes and sawed into rectangular parallelepipeds. Typical dimensions are 100 by 300 for the junction area and 100 µ for the diode height. The diodes are either soldered to a copper stud or pressure-mounted in a copper clip. RESULTS AND DISCUSSION Approximately 400 laser diodes having compositions in the range of 0.41 have been prepared by the method described above. Each laser was routinely tested at liquid-nitrogen temperature. The lasers were operated with l-psec current pulses at a repetition rate of 60 pulses per sec. The parameters of greatest practical interest are the photon energy or wavelength of the laser output and the threshold current density. Fig. 1 shows the variation of photon energy with alloy composition at 78°K. The composition was determined from the lattice constant of the material obtained by X-ray back-reflection measurements. Although there

Jan 1, 1968

By H. Udin

G. KUCZYNSKI* and B. H. ALEXANDER*—This paper represents a most noteworthy attempt to evaluate experimentally the surface tension of a solid metal. Because of the great importance of such measurements, any proposed method should receive the closest scrutiny before the results can be considered reliable. In regard to the experimental method, we think that the marking of the gauge length by means of tieing knots in the wire may be the cause of some of the spread in the results. Such a knot may be expected to tighten slightly, and thus increase the gauge length, when placed under stress at high temperature. Although this effect would be very small, amounting at most to only a few times the wire diameter. A fairly tight knot in a wire will decrease the wire length by about ten times the wire diameter, thus only a slight tightening of the knot would cause considerable spread in the results. Upon plotting the stress strain curves from the authors&apos; data, the writers found that there was a fairly consistent tendency towards an S-shaped curve, instead of a straight line. Such an effect could be caused by the tightening of the knots. The writers think, however, that the experimental results are fairly reliable, but that there may be other methods of interpreting them depending upon what mechanism is assumed to be responsible for the shrinkage of the wires. The authors have assumed that the stress due to surface tension results in viscous flow. It should be made clear that it has never been demonstrated that viscous flow can occur in metal crystals even at very high temperatures. The experiments of Chalmers13 on tin, which are so frequently quoted as giving evidence of viscous flow at low stresses are by no means satisfactory. In his experiments, Chalmers found that only the initial rate of flow was approximately proportional to stress. He also found that the rate of flow varied markedly with time which, in his experiments, was less than 2 hr. Inasmuch as there is no proof of viscous flow in metals, and the authors have brought forth no conclusive evidence on this point, it may be worth while to investigate other possible mechanisms of material transport which would account for the shrinkage of the wires. The writers wish to point out that in these experiments the shrinkage of the wires can be adequately explained, according to a self diffusion mechanism. Thus, if we assume a concentration gradient for self diffusion which is a function of the radius of curvature of the wires, and assume that diffusion will occur so that the total surface area is decreased, we find the following expression for the self diffusion coefficient: where k = Boltzmann constant r0 = initial radius of the wire T = absolute temperature ? = surface energy 8 = interatomic spacing t = time e = strain at zero applied stress Eq 19 may be used to evaluate the self diffusion coefficient of copper, using the strain measurements obtained by the authors for zero stress as obtained by extrapolating their curves for 5 rail wires. By inserting a reasonable value for the surface energy (1500 ergs per cm2) we find: -66,000 D = 5 X 10e RT [20] The activation energy is of the correct order of magnitude, but the frequency coefficient is much too high, indicating that surface diffusion may be playing an important role. This discrepancy in the action constant is much smaller than the corresponding discrepancy obtained by the authors for the viscosity coefficient. The writers by no means propose that this proves that the shrinkage of the wires is due to self diffusion but we merely wish to point out that there are explanations other than that given by the authors. In this, as in any kinetic phenomena, it is necessary to study the rate of the process before anything can be said about the mechanism. The determination of surface tension given by the authors is based upon an interpretation of the data which embody the concept of viscous flow. The final proof of this concept will be obtained only after the time relationships confirming the authors&apos; Eq 15 have been conclusively established. The rough linearity of the stress strain curves obtained by the authors for experiments run the same length of time should not be considered as proving that viscous flow is occurring. H. UDIN (authors&apos; reply)—All of the test specimens were annealed at 1000°C for an hour or more before preliminary measurements were made. During this anneal the wires recrystallize, and the greatest part of grain growth takes place. Also, the knots sinter at the cross-over points. This does not in itself eliminate the possibility of end errors, although it greatly decreases their probable magnitude. It is still possible that some extension occurs due to creep in shear at the sintered points. If so, this effect would be quite independent of and superimposed on the normal shrinkage or extension of the wire itself. Within the precision of the experimental results, straight lines satisfy the data as well as do any other simple curves. Until data of greater precision are obtained, it is futile to discuss any possible trends away from linearity. The disagreement between Kuczynski and Alexander&apos;s Eq 19 and our Eq 18 is one of semantics and mathematics, not mechanism of flow, since Eq 18 is based on the self-diffusion concept of viscous flow. It would be interesting to learn how the mathematics leading to Eq 19 deviates from that of Eyring and of

Jan 1, 1950

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,&apos; or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By Roy R. Weil, John A. Dziubek

This paper discusses the use of computer modeling, data manipulation, and mapping of three multi-seam coal properties in the Appalachian coal basin. Each case history represents a slightly different application of computer usage for estimation of reserves and planning surface mine sequencing. This practical use of computers demonstrates the suitability of data processing for normal evaluation of coal properties.

Jan 1, 1983

By W. W. Schmittroth, A. Y. Bethune

The commercial analysis of Special High-Grade zinc usually involves the determination of lead, iron, copper and cadmium as impurities in the base metal. Over the past 20 years, as the result of metallurgical improvements in the art of producing Special High-Grade zinc metal there has taken place a gradual exclusion of almost all extraneous elements, and the few that do remain in the final product have been virtually reduced to the vanishing point. Thousands of tons of zinc are now commercially produced annually and made available to the trade, in which impurities are present only in the order of 0.0010 per cent or less and the sum total of all impurities does not exceed 0.0025 per cent. To such zinc the term "super-purity" might well be applied without undue exaggeration. The techniques used for production control and final analysis of Special High-Grade zinc by means of emission spectra in the laboratories of the electrolytic zinc plant of the Sullivan Mining Co. are based on the premise that self-electrodes are to be preferred over all other forms for the examination of the zinc in question. Furthermore, after a survey of the literature and considerable experimental work,&apos; it was decided that the spectrographic method of internal control, the principle of which was first announced by Gerlach,2 using a modification of the high-voltage alternating-current arc source introduced by Duffendack and Thompson,3 with the calibration of each photographic plate as recommended by Wolfe,4 would yield the most accurate and reproducible results. Self-electrodes were chosen in order to make use of one of the unique advantages inherent in spectrographic analysis; namely, the rapid and almost effortless detection of elements other than those being quantified by the analyst; or conversely, the proof that the zinc is free from such impurities if no spectral line of the suspected element appears. This fact was verified for certain elements, and will be discussed later. Carbon electrodes impregnated or packed with zinc salts chemically prepared from the zinc to be assayed were avoided for a number of reasons. First, the chemical manipulation was another time-consuming step, which increased the chances for contamination. Second, none of the common zinc salts, such as the chloride, nitrate or sulphate, yielded reproducible results under our conditions, nor did the spectral line of the impurity appear as readily in the low concentrations as when using zinc metal. Third, no commercial carbon, except the very expensive, was pure enough to use with this grade of zinc and the continued time, effort and expense incurred in the purification of carbon were not desirable. The use of special High-Grade zinc self-electrodes introduces certain complications with regard to obtaining satisfactory excitation conditions, because it seems necessary to raise the temperature

Jan 1, 1949

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors&apos; reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

While coal was undoubtedly seen by the Spanish explorers in Texas, no mention can be found of it in any of their available published records; it was likely noticed by the first Americans, and coal along the Rio Grande River was reported in 1834.1 The next record is that of brown coal in Bastrop County in 1837 by James Nicholson and Judge Pinckney Hill? Dr. Riddell saw brown coal along the Trinity River in 1839 and described it as follows: "In the banks of the Trinity, associated with the iron ore, and overlying the brown coal, whole trees and fragments of trees, piled sometimes one upon another, present themselves completely transformed into stone. In some logs a diversified metamorphosis is observable; one portion of the vegetable structure having been replaced with silex, another with brown oxide of iron, and a third is bitumenized or converted into coal. "In concern with Dr. F. B. Page, I took considerable pains in the exploration of the Trinity brown coal formation., As no excavations for working have yet been made, the best places for inspecting the formation are where the Trinity cuts its way through the highlands, or where its banks present themselves in bold high bluffs, as at New Cincinnati, and near the site of the projected town of Osceola. The coal lies in horizontal strata, dipping one foot in thirty to the northwest. The main stratum at the latter place, just above Bedias creek; is represented by the concurrent statement of W. C. Brookfield, surveyor, Mr. James S. Hunter, of Huntsville, Texas, Dr. Page, and some other persons whom I consulted, as between six and seven feet in thickness, the lower portion being between three and four feet above low water mark. Unfortunately, during my sojourn there, the river was unusually high and turbid for the season of year; I could not consequently verify the same by personal observation and measurements. The most considerable coal beds which I had opportunity fully to inspect, were in the Trinity bluffs, southwest side, at New Cincinnati, six miles lower down, and just below the mouth of Salt creek, near six miles above. The workable stratum of brown coal in each of these localities is about five feet thick, and situated some fifteen feet or so above low water mark. In quality it is said to be precisely similar to the coal in the seven feet bed."2 . Moore in 1840 mentioned coal in the vicinity of Great Salt Lake, through which the Brazos flows; lignite in Bastrop County; lignite in the banks of the Colorado River a few miles above Lagrange in Fayette County; a deposit of excellent coal in the bed of the Sabine River, 30 miles above the

Jan 1, 1942

By C. Fairhurst, A. M. Starfield

As a practicing mining engineer, I face many rock mechanics&apos; problems daily and would like to mention one or two examples to illustrate the current gap between laboratory investigations and actual field problems. I would like to endorse Dr. Obert&apos;s suggestion that more field measurements and observations should be undertaken. There is an ever-increasing body of data beginning with Hast&apos;s results in Sweden,l then measurements at Elliot Lake, Canada, and so on, including our own measurements at White Pine, which clearly indicate that the horizontal stresses underground are often at least as large as the vertical stresses. Visual obsenation of the deformation of roof and pillars (including failure due to horizontal compression) also demonstrates that the horizontal stresses are often most important. Yet almost every laboratory investigation begins with the assumption that the only stresses acting are vertical. Roof spans in layered formations. for example, are calculated on the assumption that the rock behaves as a gravity loaded beam. This is all too often unrealistic. Roof bolts are also often considered to be simply means of suspending the gravity loaded beams. As Dr. Reed has mentioned they are probably, in fact, acting to restrain a beam which is attempting to buckle due to lateral pressure. The fact that moisture can reduce the strengths of some rocks as much as 50 percent has been known for many years. In the mine me are almost always faced with wet rock, yet no one has investigated ways in which this wakening effect can be overcome. as, for example, by waterproofing the rock. C. Fairhurst, University of Minnesota I would like to mention that we have found,2 from stress-relief determinations, that appreciable (over 1000 lb per sq in.) horizontal pressures occur also at the surface in granites quarried in central Minnesota. Whilst I agree that more field measurements are desirable, it is important to point out that most university research is undertaken by graduate students who must attend classes daily. Their research is therefore restricted to the laboratory. A.M. Starfield, University of Minnesota No one denies the importance of obtaining: data from field measurements. It is equally important, however, that field measurements be guided by theory. Much time and money can be wasted by indiscriminate measurement. An example of the value of theory in interpreting measurements is given in Dr. Obert&apos;s comments on the time dependent strain observed in a salt mine. He anticipated that the stress at the wall of the opening would change with time because salt is viscoelastic rather than elastic. It can be shown from theory that if an excavation in a viscoelastic medium is unsupported, then the stress at the wall does

Jan 1, 1967

By B. G. Hurd

A liquid-Freon permeameter suitable for making routine permeability determinations on small plug samples is described. The instrument is characterized by simplicity of design and ease of operation, and can be assembled inexpensively from stock items of laboratory equipment. It combines the unique advantages of both liquid and gas permeam-eters while eliminating many undesirable features of both general classes of instruments. Precision and accuracy of the specific Freon permeability measurements compare favorably with results of conventional liquid and gas permeameters. INTRODUCTION The liquid-Freon permeameter described in this paper was designed and built for special investigations of the properties of petroleum reservoir rocks. However, its unique advantages over conventional gas and liquid permeameters make it eminently suitable for routine use in the core analysis of small plug samples. In general, gas permeameters are very popular because of their simplicity of design and ease of operation. However, apparent gas permeabilities are normally higher than true specific permeabilities unless special corrections for gas-slippage are applied. Since these corrections require two or more measurements at different internal gas pressures, much of the time advantage of the specific gas permeability measurements is lost. Liquid permeability measurements, on the other hand, require no slip correction, but liquid saturation of the sample is time-consuming and difficult to insure. Often, too, the saturating liquid must be extracted or dried from the plug before it can be used for another experiment. The liquid-Freon permeameter described herein retains the inherent accuracy of the liquid permeameter, while affording the speed and ease of operation of the gas permeameter. Freon-12 (dichlorodifluoromethane) is a haloge-nated hydrocarbon, immiscible in the liquid phase with water. It may be considered as an oil phase in laboratory fluid-flow studies. Like butane and propane, it is a gas at normal room temperatures and atmospheric pressure but can be liquefied at moderate pressures. Complete liquid saturation of a plug sample with any of these fluids can be easily achieved by condensing vapors in the sample and operating the permeameter at a pressure above the vapor pressure of the liquid. Freon-12 is superior to butane or propane for permeability measurements only in that it is relatively nontoxic and completely incombustible, and thus presents no fire or explosion hazard. Freon-12 is believed to be completely nonreactive with most petroleum-reservoir rock samples. It volatilizes immediately from a plug on depressurizing to leave a clean, dry sample suitable for subsequent experiments. Thus, the inherent risk of changing physical properties of rock samples by cleaning and drying operations between permeability measurement and subsequent experiments is eliminated. DESCRIPTION OF THE PERMEAMETER The design of the liquid Freon-permeameter is shown schematically in Fig. 1. Regulated nitrogen pressure caps are used both as a driving pressure

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.&apos; Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function&apos; used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail&apos; and the results are simple and generally applicable. &apos;The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy&apos;s law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950