Search Documents

By John Wulff, J. H. Hollomon

The opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was re-deposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May16 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to a1pha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,a in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As2O3),

Jan 1, 1942

By M. E. True, B. L. Stone

To cope with the problems encountered when drilling at greater depths and to reduce the amount of physical effort required on the part of drilling crews in making round trips, a new type of semiautomatic power-operated drilling machinery has been developed which permits round trips to be made without the drill pipe being touched by hand. This equipment consists of hy-draulically operated tongs which perform the stabbing, spinning, and tong-ing operations, and two power-operated racking units mounted in the derrick for carrying the pipe to and from the center of the hole and positioning it on the mat and in the rack. With this equipment all of the operations of the various units are controlled remotely by manipulation of hydraulic valve levers and electric switches. INTRODUCTION As horsepower rises to meet the demand for deeper drilling, it is necessary to increase the weight of surface drilling equipment. Also, the duration of repetitive operations in making round trips to change bits is greatly increased with depth. Harder formations encountered at greater depths reduce bit life rapidly, resulting in more frequent round trips and in some instances more time is consumed in changing bits than in drilling. Since the introduction of the first rotary employed to drill for oil in 18951, there has been relatively little change in the general procedure for making up, breaking out, stabbing, and racking drill pipe in making round trips to change bits. The conventional method of making round trips with the drill pipe requires that drilling crews lend strenuous physical assistance to manually operated tools. Although many new devices have been developed to improve efficiency, increase speed of making round trips, improve safety, and reduce the amount of physical effort required in handling drill pipe, it is considered a vital necessity to substitute automatic or semiautomatic power-operated machinery for many of our more or less manual operations if extremely deep drilling is to be carried out successfully on a production basis in the same manner as our shallower drilling of today. Field tests have been made of remotely controlled power-operated tongs, spinner, stabber, and racking equipment. The tongs, which include a built-in pipe spinner, are mounted on a column, are capable of gripping and supporting the weight of a 90-foot stand of drill pipe, and are provided with means for moving the pipe vertically as well as to and from the center of the hole. The racking equipment consists of two units, one at the level of the conventional monkey board and the other at the first girth on the ladder side of the derrick. Most of the physical effort of making round trips with drill pipe has been eliminated in that all of the operations of tonging, spinning, stabbing, and racking of pipe on the floor are controlled by an operator in a seated position by manipulation of hydraulic and electric valve levers and buttons. The driller is relieved of operating the cathead, leaving only the hoisting and slips to be controlled. Complete round trips are made without the drill pipe being touched by the drilling crews. Although the speed of pulling or running a single stand with the power-operated equipment is approximately the same as that with conventional equipment, it is possible to maintain this rate for long periods, whereas fatigue slows crews working conventionally during round trips, especially under adverse weather. After completing round trips with this equipment, drilling crews are not exhausted, consequently, are able to perform effectively their duties while drilling, which is essential for maximum over-all efficiency. Safety is substantially improved as the derrickman performs his duties from a platform enclosed by rails and the tong lines and spinning chain are eliminated from the derrick floor. The hazards encountered in racking drill pipe on the floor and in stabbing are also eliminated. Figure 1 shows a drawing of a derrick equipped with the power-operated drill'pipe handling equipment.

Jan 1, 1949

CONTENTS PAGE East Texas, except the Gulf Coast-H. Vance 3 Gulf Coast-L. P. Teas 8 Texas Panhandle-C. C. Rae 16 North Central Texas-H. F. Smiley 23 North Louisiana, South Arkansas and Mississippi-B. C. Craft 25 Oklahoma-C. H. Pishny, Raymond M. Carr and E. J. Dickinson 31 Kansas-E. A. Koester 35 Rocky Mountain District-C. D. Johnson 46 Illinois and Indiana-T. Wasson 49 Michigan-T. Wasson 52 Eastern States-P. D. Torrey and W. H. Young, Jr 58 West Texas and New Mexico-W. V. Vietti. Published as a Supplement.

Jan 1, 1933

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By Lawrence B. Wright

The occurrence of gold, gold-silver, silver-lead-zinc ores in the post-Cambrian sediments in the Black Hills of South Dakota, and their genetic relationship to the Tertiary intrusives, is well known and accepted, but the occurrence of gold in the pre-Cambrian rocks at the Homestake mine, which underlie this Tertiary gold mineralization, has given rise to differences of opinion as to the period of major gold introduction into the older rocks. Fig. 1 illustrates the distribution of mineralization along the axis of the Tertiary uplift in both pre-Cambrian and post-Cambrian rocks. The following possibilities have been presented: 1. The Homestake gold deposit was formed in pre-Cambrian time and the deposits in the overlying Cambrian sediments formed during Tertiary time. 2. The Homestake lode existed at the beginning of Cambrian time, but was enriched by the passage of Tertiary auriferous solutions. 3. The Homestake lode was represented by pre-Cambrian quartz-chlorite sulfide mineralization, very low in gold content and the gold superimposed on the older nearly barren mineralization during the Tertiary metallogenic epoch. 4. The sulfides and sulfarsenides as well as gold were deposited in both pre-Cambrian and post-Cambrian rocks during the Tertiary period. Those favoring the first proposition feel that the question is pretty well settled, while the proponents of the second theory are more flexible in their view, feeling that the amount of gold introduced in either period is still an open question. The third and fourth theories, with some modifications, are supported by the proponents of the Tertiary theory, who feel that the evidence strongly favors that period. The following pages are intended to present the evidence and to give the reaction of various observers with my own comments and conclusions; also, the accumulated facts of observation gathered over a period of close association with the area under discussion, beginning in 1919.

Jan 1, 1937

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

The microstructural stability of 59 carbon and low alloy steels after 34,000 hr exposure at 900' and 1050°F, including the weld heat-affected zone, is discussed. The tensile and creep rupture properties of the parent metal of many of the steels before and after 10,000 hr exposure are presented. SEAMLESS pipe has been used for many years at elevated temperatures. When seamless first began to be used, operating temperatures and pressures were relatively low and the steel produced adequately met the existing requirements. The need for knowledge of creep properties and graphitiza-tion was nonexistent. Today the requirements for tubular products have changed considerably. Operating temperatures and pressures are increasing continually and corrosion, particularly at high temperatures, presents a problem. Carbon steels have, under these conditions, certain economic advantages particularly in oil refinery use. However, the use of low alloy steels in the generation of steam power has increased appreciably due to the influence of molybdenum on creep strength and the control of graphitization with chromium. The behavior of carbon and certain low alloy steels after long periods of exposure at 900° and 1050°F (480° and 565°C) has been investigated. The steels were examined before and after 10,000 to 34,000 hr exposure. Results obtained with material exposed at 1200°F (650°C) are not presented due to the severe oxidation and resulting decarburiza-tion after long periods of exposure. The graphitization characteristics of carbon and low alloy steels are of fundamental concern to the users of these materials. This is particularly true where welded joints are employed. In order to evaluate properly the behavior of steels at elevated temperatures, it is desirable to employ not only long periods of exposure under controlled conditions, but to use material with known properties and steelmaking practices. The purpose of this investigation has been to study the microstructure of the weld and the tensile and creep rupture properties of the parent metal after long periods of exposure at elevated temperatures. In the report'.' of a previous investigation data were presented on the microstructure, impact strength, hardness, and oxidation characteristics after 10,000 hr exposure at elevated temperatures. When this investigation was planned, methods for controlling the graphitization characteristics of steel were not established and, therefore, a number of special alloy steels were included in the study. During the exposure of these steels, the influence of aluminum in accelerating the rate of graphitization and the inhibiting power of chromium were established by various investigators. Also, the vanadium-bearing steels, because of their outstanding creep properties, received attention. As a result of these developments, considerable progress has been made in the field of high temperature tubular products, and the necessity for special alloys to prevent graph-itization has been restricted largely to the use of chromium. Material Chemical analysis, deoxidation treatment, and austenitic grain size of the 59 steels discussed in this paper are shown in Table I. The steels were forged to 1x1 in. bars with the exception of steels 12B, 12DX, 12DY, 12DZ, 70, 70A, 72 to 78, 82, and 83 which were machined from heavy wall pipe. All bars were surface ground before exposure. Heat treatment before exposure is shown in Table 11. The majority of the steels included were melted in either a basic open hearth or basic electric furnace; how-

Jan 1, 1955

By G. B. Walker, S. J. Swainson, S. A. Falconer

DURING the past few years much interest and attention has been focused on a relatively new method of ore concentration, which utilizes the principles of sink and float and employs as the heavy medium a suspension in water of a finely ground solid, such as galena or ferrosilicon. Although a relatively recent development, much progress has already been made in applying heavy-media separation processes to a considerable number of ores. Eight plants in this country and abroad -are now treating approximately 10 million tons of ore annually by heavy-media separation (sink-float) processes, including lead-zinc, lead, iron, garnet, tin and tungsten. At the annual meeting of the A.I.M.E. in 1941, three interesting papers (unpublished) dealing with heavy-media separation (sink-float) processes of ore concentration as practiced in four commercial units in the United States were presented by Victor Rakowsky, Grover Holt, Elmer Isern and Robert Ammon. These papers gave an excellent exposition of the principles of sink and float, as well as the operating practice in two iron-ore-beneficiation plants, the Harrison and the Merritt, of Butler Brothers, in Minnesota; the Central mill of the Eagle Picher Mining and Smelting Co.; and the Mascot mill, of the American Zinc, Lead and Smelting Co. Augmented by pictorial descriptions and a working model demonstrating the processes, these papers evoked a great deal of interest and discussion. In fact, in reporting the high lights of the meeting in the April 1941 issue Of MINING AND METALLURGY, Professor Taggart made the statement that "preconcentration by heavy suspension was Miss A.I.M.E. 1941 so far as milling is concerned." Although to date the greatest application of heavy-media separation from the tonnage point of view has been for the treatment of lead, zinc and iron ores, these processes have a much wider field of usefulness. In this regard, it is to be noted that recently new heavy-media separation plants for treating cassiterite ore and garnet ore have been placed in successful operation. Moreover, numerous other types of ores have been found to respond well to these processes when tested on a semi-commercial scale, and it is expected that in the near future a considerable number of new plants will be erected. In view of the fact that heavy-media separation processes offer such attractive possibilities, particularly now, when the mining industry is being called on for an even larger production than ever before has been attempted, despite shortages of labor and supplies, it was felt that a description of some of the successful separations that have been worked out during the past year in the Ore Dressing Laboratory of the American Cyanamid Co. on a variety of ores of strategic importance would be of interest. The purpose of this paper, therefore, is to present the essential data relating to investigations of heavy-

Jan 1, 1943

By Per Kofstad, Hallstein Kjöllesdal

The oxidation behavior of niobium (columbium) has been studied in the temperature range 500° to 1200°C and at oxygen pressures of 760,100, 10, 1, and 0.1 mm of Hg. The work comprises kinetic studies of the oxidation as well as structural investigations of the oxidized specimens by means of X-ray diffraction, electron diffraclion, electron microscopy, and metal1ographic techniques. The oxidation reaction has a highly irregular temperature dependence and is unusually sensitive to changes in the oxygen pressure. The complex oxidation behavior is suggested to be due to formation of different Nb2O5 modifications in different temperature regions. During oxidation oxygen is also dissolved in the metal. Formation of oxide whiskers take place on the oxide surface at temperatures above approximately 800°C. VARIOUS aspects of the oxidation of niobium have been studied.l-12 The investigations show that niobium has a complex oxidation behavior, and the oxidation

Jan 1, 1962

By William Fink

THIS paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium) relations have been deter-mined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and alu-minum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith? suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extent 1,2,3. The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are dis-tinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns.

Jan 1, 1936

By G. F. Loughlin

MORE than 20 years have passed since the publication of Lindgren and Ransome's report on the Cripple Creek District,1 which was made when the district was much more active and prosperous than in recent years. They concluded that the output of the district, which had reached its maximum of about $18,200,000 in 1900, would gradually decline, and their conclusion has been confirmed by records of subsequent production. Between 1905 and 1915 annual declines were partly compensated by encouraging increases, especially in 1908, 1914, and 1915; but a rapid continuous decline followed, due largely to the war and its after effects, until in 1922 the value of output was only slightly more than $4,000,000. It rose to nearly $5,000,000 in 1924, but declined again in 1925 and in 1926, when it was about $4,400,000, and represented ores mainly from deep levels in the Cresson and Portland mines. The profitable operations of these two mines were the principal factors leading to a study of ore at deep levels in the district by the U. S. Geological Survey in coopera-tion with the Colorado Metal Mining Fund. The principal reasons for Lindgren and Ransome's conclusion were three: (1) the greater cost and difficulty of deep exploration; (2) the decrease in the number of veins with increasing depth, and (3) the probability that the telluride ore, believed to have formed at comparatively low temperature, would not persist indefinitely -in depth. Operations since they made these statements have verified the first two, but call for some modification of the third. Rich telluride, ore is being mined at a profit in the Portland mine 3000 ft. below the present surface, or 5000 ft. below the original surface of the Cripple Creek volcano, as interpreted by Lindgren and Ransome. The question arises, therefore, as to the number and extent of such deep deposits, and the answer, so far as it can now be given, must be based mainly on structural data, supplemented by data on the processes of ore deposition. Presentation of these data based on a study of deep mines in the southeast quarter of the district, the only

Jan 1, 1927

By A. S. Richardson

THE recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By Richard V. Hughes, Rudolf J. Pfister

The necessity for getting more water into sands of low permeability in any secondary-recovery water-flood operation in order to recover all the available oil always has been a major problem. In the early days of water-flooding the addition of soda ash and caustic soda to fresh input waters was recommended and tried without success in the Bradford field. The most frequent difficulty was sand plugging. The use of natural and artificial brines often has been suggested for water-flooding, in the belief that laboratory observations of decreasing fresh-water throughput rates in measuring water permeabilities of consolidated sand cores might be partially explained by swelling of clays. A review of available literature bearing on the subject and related laboratory experiments are presented herein, offering an explanation for failure in use of soda ash and caustic soda waters and supporting the recent concept that every water used for input purposes in the secondary recovery of oil should possess such physical and chemical characteristics as to keep the clay content of the producing sands in a permanently flocculated condition. Produced brines meet this requirement. Their use is recommended as a means of increasing intake rates of tight sands and oil recoveries, as a solution to brine-disposal problems, and as a means of conserving a natural resource. Introduction There is a general belief among those engaged in the secondary recovery of oil by water-flooding that one of the most important requirements for the success of any such project is an adequate supply of good, fresh water. Fresh waters have the advantages of being more easily stabilized than salt waters and of being usable about the lease for all purposes. The use of brines for water-flooding never has been given much consideration in the Pennsylvania Grade area. The use of brines in Mid-Continent operations has been considered largely as a substitute for fresh waters, which were economically unobtainable for many operations. Estimated recoveries for some water-drive fields indicate that less of the original oil in place will be left upon abandonment than with the above-average practices used in Pennsylvania Grade water-flood operations. Lower residual oil saturations than 25 pct of the pore space following the water-flooding of Third Bradford sand cores in the laboratory are unusual. In comparison, water-flushed sands surrounding any virgin oil pool are found to be practically devoid of oil. Such lower natural residual oil saturations may be the result of a time factor much longer than economic under artificial water-flood operations, but neither the producer of primary oil nor the producer of oil by secondary recovery can obtain maximum recoveries unless full advantage is taken of all natural forces and

Jan 1, 1947

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,' six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 11893. As late as 1923, according to Richardson, 2 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change in table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end, of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box with the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By V. C. Allison

Large-scale testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparntion of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments conducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have becn reviewed by the Bureau of Mines.' The Bureau has conducted many tests with the Frazer-Cle1ncnt5 apparattus, which gives the pressures set up when the dust cloud within is ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. Need for a Dust-testing Apparatus An attempt has been made to design an apparatus that may be used for checking and correlating the expcrimental tests. The first design was a wooden gallery, 8 by 10 in., inside cross section, and 12 ft. long, and having a number of strips along each side for creation of turbulence. The wooden gallery did not get beyond its period of calibration; it mas difficult to make the gallery sufficiently tight, for it was necessary that the top be removable in order that the gallery could be cleaned. In the use of the wooden gallery, however, sufficient operating data were obtained to be a guide in the design of a steel gallery having a circular cross-section. One of the features was a flap valve, at the closed end of the gallery, that would open inwardly thus preventing a reduced pressure within, caused by the cooling of the gases of combustion, and the explosions propagated much better than when the valve was not used; another feature was the determining of the best method for getting a cloud of dust simultaneously in all parts of the gallery, which was accomplished by the use of the concussion wave of a small quantity of powder or by the use of compressed air.

Jan 1, 1927

By V. C. Allison

The explosibility of a dust is favored by its fineness and content of volatile combustible matter; its explosibility is decreased by its moisture and ash content. The explosibility of a dust can be reduced by admixture of either inert dust or water. The major effect of both the inert dust and water lies in their heat capacity; they absorb the heat of the explosion flame until the temperature of this flame drops below the ignition temperature of the explosive heat. The amount of inert dust necessary to make an explosive dust non-explosive can be calculated from its proximate analysis. FOREWORD LARGE-SCALE testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparation of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments con¬ducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have been reviewed by the Bureau of Mines., The Bureau has conducted many tests with the Frazer-Clement2 apparatus, which gives the pressures set up when the dust cloud within is, ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. An attempt has been made to design an apparatus that may be used for checking and correlating the experimental tests. The first design was a wooden gallery, 8 by

Jan 7, 1925

By W. R. Hibbard

The increased strength of a polycrystal-line metallic aggregate compared with that of its individual crystals generally has been associated with complex stress distributions at the grain boundaries resulting from atomic irregularity between grains. This disregistry, together with the necessity for adjacent crystals to deform compatibly regardless of the single crystal crystallo-graphic strain mechanism, complicates this mechanism so as to increase the metal's resistance to deformation. Although Taylor1 has shown from purely mechanical considerations the requirement for at least five active slip systems to absorb the complexities during the homogeneous deformation of polycrystalline face-centered cubic metals, experimental studies by Barrett and Levenson2 indicate that this is feasible only in a qualitative sense because of deviations from homogeneous deformation. Seitz and Read in their review3 state: " Unfortunately . . . present knowledge of the grain boundary influence is not sufficient to complement the work in single crystals and provide us with a good foundation for treating polycrystals." The purpose of this investigation was to attempt to clarify the gap between single crystals and crystalline aggregates by an analysis of the effects of dcformational stresses. Some of the results were described by C. H. Mathewson in his 1943 Campbell Memorial Lecture.zl Previous Investigations Since the performance of single crystals deformed under pure stresses has been relatively thoroughly investigated, the most significant researches are concerned primarily with deviations from single crystal behavior of large grained specimens. Qualitative grain boundary effects involving the observed amount of slip werc reported by Carpenter and Elam5 in 1921. Individual crystals in a two or three grained aluminum specimen deformed by tension acted in the normal manner described by Taylor and Elarn4 except for marked modifications at the grain boundaries. There the power to withstand deformation was considerably increased, leaving a ridge on the specimen where decreased slip occurred, often noticeable yi in. from the boundary. Adcock,6 Yamaguchi,' Seumel, Hirstg and others have also reported this phenomenon as a qualitative trend. Yet attempts by O'Neill'o and Ljunggrenll to measure a difference in hardness at grain boundaries in undeformed specimens were unsuccessful. Miller12 measured quantitatively the reduction in slip near the boundary between the single crystal and polycrystalline areas of zinc specimens. These effects consisted of two parts: I. Next to the polycrystalline interface thc distribution of stresses was so altered

Jan 1, 1949

By O. R. Bergmann

Two approaches were taken to obtain direct experimental evidence jar the existence oj a jet in the explosion-cladding pvocess: 1) direct observation of the claddirg jwocess by rtzeans ojf kig-h-speed photography using a fvartziiy catnera and 2) use of a plated-surface experiment in contribution with clzetrzical analysis. The framing-camera records showed clearly the presence of a jet it1 the form of what appears to be a line spray. The jet velocity is considerably highev than the detonation velocity arid in vacuum it is almost twice as high as the detonatiou velocily. The results jrorrz the plated-surface experiment also corzfivtned the preseizce of- a jet. The artzoutlt o,f etzergy dissipated in the jetting process was foundd lo be consislent with the basic theovetical model o/ the cladding mechanism.. MaNY reports on metal working with explosives have appeared in the literature during the last few yearsThis paper describes experiments concern- ing the mechanism of the explosive metal-cladding process. It has become increasingly important as a unique method for bonding metals and a typical cladding arrangement is shown in Fig. 1. A theoretical analysis of the mechanism of explosive bonding and a description of the nature and types of bond zones obtained was given by Cowan and oltzman." A further discussion of the basic principles of the process, a detailed description of the different bond-zone types, and extensive information on the properties and the applications of explosively bonded metals was recently published by Holtzman and cowan. " The process is now in commercial use by E. I. du Pont de Nemours & Co. The concept of the existence of a jet during metal bonding with explosives forms a central part in the theoretical analysis of the cladding mechanism described by Cowan and Holtzman When a layer of explosive is detonated on a metal plate that is separated from a second metal plate by a small distance the metal plate in contact with the detonating explosive is accelerated by the detonation pressure. An angle is established between the undeflected and deflected portions of the plate. Subsequently the deflected portion of the first plate collides with the second metal plate.

Jan 1, 1967

June was the month in which AIME was founded in the year of 1871. For some reason, February was selected as the month for the legal Annual Meeting. One can't help thinking wistfully of Annual Meetings in June but of course this is not the reality. Because the Centennial Ceremonies are taking place in February, that month has been chosen as the one in which MINING ENGINEERING, the monthly magazine of the Society of Mining Engineers, a constituent society of AIME, is publishing its Commemorative is- sue to celebrate the event. SME and ME take a proprietary air about AIME. This is mostly because AIME started as the American Institute of Mining Engineers. Metallurgy was added to the name in 1919 and Petroleum in 1956. The official abbreviation of "AIME" has been retained, however.

Jan 1, 1971

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963