Search Documents

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

By J. F. Smith, J. R. Ogren, N. J. Magnani

The uapor pressrcres of magnesium over binary alloys of magnesium with twelve of the yare-earth eletnetzts have been measured by the Knudsen effuion method in the temperature range 675° to 910°K. These vapor-pressure measurments were combined with data concerning the tevtrlitzul magnesium solubility and the vapor pressure of pure magnesinm to evaluale the standuvd free energies of pluase jormation. These free-etzergy values indicate that the CsCl structures of the heacy rave earths tend to be somewhat less stable than those of the light rare earths. This dif-]eying- behaviov covrelates with differences which have been obsevz~ed in other alloy systetns wherein a phuse appeurs, disappeavs, or changes crystal stvucture as the atomic number of the rare-earth com-ponent is changed. This behauior also appears to correlate with the struclurul rariations within the rare-earth elements themselves, and it is speculated that cariations in the spatial extent of the 4f orbitals are responsihle. STUDIES of the phase relationships and crystal structures in the binary systems between rare-earth metals (lanthanons) and magnesium are extensive but far from complete. However, the currently available information1-10 does produce a rather interesting pattern. This is illustrated in Table I. If one excludes europium and ytterbium from consideration because of their generally atypical behavior, it can be seen from the table that the phase relationships in the magnesium-rich regions show a distinctly different pattern for the lighter lanthanons as compared to the heavier lanthanons. For the lighter lanthanons, LnMg2 phases occur from lanthanum to gadolinium with the cubic MgCu2 structure, LnMg3 phases occur from lanthanum to terbium with the BiLi3 structure, and magnesium-rich phases occur from lanthanum to gadolinium with stoi-chiometries between Ln5Mg42 and LnMg12. In contrast, for the heavier lanthanons, those LnMg2 structures which have been examined have the hexagonal MgZn2 structure, LnMg3 phases have not been observed beyond terbium, and the magnesium-rich phases occur with the a manganese structure near a stoichiometry of Ln5MgZ4. The heavy lanthanon-magnesium systems thus appear to be analogous to the Y-Mg system""2 wherein YMg has the CsCl structure, YMg2 has the MgZn2 structure, and the region Y4Mgz5-Y5Mg24 has the a manganese structure, and no other intermediate phases are observed. Similarity in alloying behavior between yttrium and the heavy lanthanons occurs commonly, and on this basis it seems likely that LnMg2 phases will be found with the MgZn2 structure in the binary systems of dysprosium, thulium, and lutetium with magnesium when the appropriate investigations are made. In the case of the magnesium-rich phases of the lighter lanthanons, only the Ce-Mg phase relationships have been investigated thoroughly and in detail, and until similar investigations are made for the other systems there will remain questions as to which magnesium-rich stoichiometries represent equilibrium phases and what systematic variations occur in the sequence from lanthanum to gadolinium. Thus the data in Table I show that only the LnMg phases occur with the same crystallographic structure throughout the sequence from lanthanum to lutetium. It was speculated that the relative stability of these LnMg phases might vary from one lanthanon to the next in such a way as to presage the differences which occur among the more magnesium-rich lanthanon-magnesium phases. On this basis the present investigation of the thermodynamics of phase formation was Gndertaken for the LnMg phases. PROCEDURE AND RESULTS A generalized phase diagram for the lanthanon-rich portion of a lanthanon-magnesium alloy system is shown in Fig. 1 where ß represents a high-temperature bcc

Jan 1, 1968

By Richard P. Gerwels

Minas de Matahambre, a copper mine located 100 miles southwest of Havana, Cuba, has produced 10 million tons of copper ore since it was first opened up in 1913. During the mid-1950's the mine was producing approximately 1000 tpd and had attained a depth of 3600 ft. As shown in Fig. 1, the property contains three shafts: the No. 1 shaft, 2100 ft deep and located 2000 ft south of the No. 2 shaft, provided service to the 2100 level; the vertical 3600-ft No. 2 shaft handled all production to the 3400 level; the No. 3 shaft on the northeasterly fringe of the mining area was in a semi-active status.

Jan 12, 1960

By Thomas Henderson

Strategically, intermaterials competition is important to companies involved in raw materials extraction, smelting, refining or other processing, semi-finished and finished goods fabrication, and end-use consumers. In other words, just about every company involved in manufacturing. The array of materials covered by other papers in this session is testimony to the subject's breadth. In trying to provide an over- view of such a broad topic, the purpose has been to relate some of the common characteristics of the markets, economics and technology of raw materials, and to describe some of the ways in which Intermaterials competition impacts the markets, economics and technology of raw materials.

Jan 1, 1982

By A. H. Geisler, J. H. Keeler

Preferred orientations in rolled and annealed titanium sheets were determined by the Geiger counter spectrometer X-ray diffraction technique. Five annealing textures dependent upon the temperature range of annealing were found, and in order of increasing annealing temperature pendent upon the temperature range are: 1—a deformation like texture, 2—a rotated inorder a-recrystallization temperature texture, 3-a retained u-recrysraIlization texture, on annealing at lower temperatures of the ß-region, 4—a transformation texture based on recrystallized a and predicted by the Burgers' relationship, and 5—a ,ß-cube texture. These results are examined in terms of current theories of recrystallization textures. UMEROUS investigators have described the tex- ture obtained by cold rolling the hexagonal metals, titanium, zirconium, and beryllium, which have c/a ratios less than that of ideal packing, 1.633. The basal planes are rotated out of the rolling plane, about the rolling direction, so that the basal poles are tilted toward the transverse direction as shown schematically in Fig. la. In all instances but one,' it was also reported that the [1010] direction was parallel to the rolling direction (see Fig. lb). Hot rolling has been reported as causing a similar tilt of the basal poles in the transverse direction (see Fig. la) and causing the [1010] direction also to be parallel to the rolling direction as shown schematically in Fig. lb. Annealing after deformation does not appreciably change the tilt of the basal poles in the transverse direction." Beryllium2-7 continues to have the [1010] direction in the rolling direction after annealing, and similar observations for titanium and zirconium' . have been reported for annealing at fairly low temperatures, again as in Fig. lb. At higher annealing temperatures, however, the recrystallized grains of titanium" and zirconium have an orientation such that the [1120] direction is approximately in the rolling direction, although the basal poles are still inclined in the transverse direction. Figs. la and lc show the resulting orientations schematically. This change in orientation has been described as a nominally ±30° rotation of the hexagonal crystallites about the basal poles of the cold rolled texture and is apparent from the results which are summarized in Table I for investigations with the X-ray diffraction technique employing film. The angles y, , and ß are indicated in Fig. 2 which represents the stereographic projection of (1070) poles for the mean orientation of a pole figure. Texture determinations for titanium using the Geiger counter spectrometer have provided similar results except that in some instances additional components of the texture were proposed, as shown by the summary of data in the upper half of Table 11. On the other hand, the spectrometer technique, when applied to zirconium,* has revealed a splitting Recently completed studies of the textures of annealed zirconium", show zirconium to possess textures very similar to those reported here for titanium. Therefore, much of this discussion will include zirconium by virtue of its close similarity to titanium in pref erred orientations. of the intense areas of the pole figure for samples annealed at 600°C. This splitting could be described by a 7" rotation of the tilt axis about the normal to the rolling plane. Such a splitting for the annealed texture relative to the cold rolled texture was not observed in other determinations for either zirconium or titanium using the less sensitive film X-ray methoe and makes the relationship between the two types of texture more complex than the simple rotation about the (0001) pole based on film work. The more precise investigations on zirconium permit the descriptions in the lower part of Table 11, which show that the texture depends quantitatively on the temperature of annealing. When zirconium is annealed at temperatures up to 400°C, the texture is similar to the cold rolled texture, while annealing in the range 500" to 900°C produces a texture which is only approximately described as [11%] in the rolling direction. More precisely described results for zirconium show that the two types of splitting ( 1—about an axis in the rolling plane through an angle given in the second column in Table II and 2—about the normal to the rolling plane through an angle given in the third column of Table 11) depend on annealing temperature. The [1120 is the rolling direction only when the annealing temperature is in the vicinity of 900°C

Jan 1, 1957

By AIME AIME

THE growth of the spirit of progress and mutual aid which motivated the founders of the Institute sixty years ago in Wilkes-Barre was vigorously demonstrated at the sixtieth anniversary meeting held there on May 22. Committees headed by Cadwallader Evans, "resident director" of the Institute, and Paul Sterling, chairman of the local section, had arranged for a full-day tour of the northern anthracite field, so that the hundred and fifty members and guests who had come for the celebration of the anniversary might see the changes and progress made in that field in recent years. More than forty automobiles were in line in the cavalcade which left the Westmoreland Club at nine- thirty. Operations visited were fully described in the May issue of MINING AND METALLURGY, so it is enough to say that after a seventy-five mile drive through the beautiful Susquehanna Valley and over the rolling green hills of northern Pennsylvania a stop was made for lunch at Forest City. Carey, Baxter and Kennedy, contractors at the stripping operations there, had provided, in the shelter of tents, a well-prepared luncheon and other refreshments. The return trip was made by way of Scranton, arriving at Wilkes-Barre at five- thirty.

Jan 1, 1931

By Frederick Laist

(Butte Meeting, August; 1913.) WHILE remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the -treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was, decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the MacDougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide.

Jan 7, 1913

By C. D. Dolman

SINCE the outbreak of the war we have discovered in the United States minerals of which there was no general knowledge, and which compared very favorably with anything that could be found in any foreign country. One of these was magnesite, or the carbonate of magnesium as it occurs in nature. This mineral crystallizes in the rhombohedral form, has a specific gravity of 3.00, molecular weight of 84 4, molecular volume of 28.1, and a hardness of 3.5 to 4.5.1 Had it not been for the development of the California deposits of this mineral and the discovery of immense new deposits in Stevens County, Wash., the production of steel during the war would have been more seriously handicapped than it was. Now, that the war is over, we face the possibility of competition' with the cheap Austro-Hungarian magnesite; and while that may not he so cheap as it was before the war, adequate protection should be given the producers in this country to insure the full development of our own resources. The consumption of magnesite in the United States in 1913, the year preceding the war, was 172,591 tons of calcined and 22,872 tons of crude magnesite. Less than 3 per cent. of this amount was produced at home. At the present time, practically all of the magnesite used in the United States is produced at home. Expensive plants have been constructed, extensive exploration work done, and production pushed to the utmost to supply the necessary requirements of the war. Thus a considerable industry has been built up within our borders. Some magnesite has been imported from Canada and Mexico, but the Canadian ore was of an inferior grade and could not be used satisfactorily. During the year 1918, production decreased in both the United States and Canada; the production in the United States was 225,000 tons in 1918 as against 315,000 in 1917, and in Canada 39,365 tons in 1918 as against 58,090 in 1917.

Jan 8, 1919

By H. M. St. John

Like every present-day manufacturer, the brass foundryman is faced with the necessity of reducing the cost of his finished product without impairing its appearance or quality. He must use every economy that the progress of art and science puts at his disposal and should also be alert to profit by any peculiarity in his own situation or the nature of his product that may give him an exceptional advantage. Much can be accomplished by the adoption of labor-saving equipment and improved methods of melting, molding and handling. Control of pouring temperature, study of defective castings and their causes, laboratory control of molding sand and core mixtures, the use of less expensive alloys, all contribute to the desired end. Assuming that the composition of the alloy is already as inexpensive as the character of the casting will permit, still further savings can be made by the intelligent purchase and utilization of the metals needed to produce the desired analysis. Functions of Secondary and Virgin Metals in Casting Brass It is no longer a general assumption among foundrymen that quality castings must be made from an "all virgin" mix. If suitable secondary metals can be obtained more cheaply it is wasteful to use any larger proportion of virgin metal than is required to produce castings of the desired properties. To follow such a course, however, imposes upon the foundryman a heavier obligation than was formerly the case, to make sure by test and inspection that his castings really are of the desired quality. So long as he used the most expensive grades of metal and his melting practice was reasonably correct he was not obliged to give much thought to the quality of the metal in the castings. If he is to use secondary metals he must, in order to retain the confidence of his customer, examine these metals very carefully before use, exercise scrupulous control over his melting and pouring conditions and examine his castings closely. These statements apply more particularly to the jobbing foundry. The foundry department in a manufacturing plant is in a somewhat

Jan 1, 1930

By Charles Fettke

The deposits described occur in a belt starting 1 ½ miles east of Juncos and extending 6 miles in a southeasterly direction. They are of the contact metamorphic type, being associated with a limestone and calcareous tuff that is interbedded with andesite tuffs and andesites which have been invaded by a quartz diorite intrusion. Of the fire occurrences examined, the largest can be traced for a horizontal distance of 2000 ft. No mining has, been done, but some of the outcrops lead to the belief that deposits of commercial size are present. IN CONNECTION with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,1 a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 1 ½ miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated

Jan 2, 1924

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported1 that acid-soluble titanium decreased the hardenability, with multiplying factors less than unity according to Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying fdctors up to nearly I.; for about 0.1 per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 1.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correc- tion for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non-titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. Comparison of Plain-carbon, Vanadium and Titanium Steels The five steels used for these experiments were cominercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat1 containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain carbon

Jan 1, 1947

By George C. Heikes

ALTHOUGH the application of light metals in war materiel increased during the year, based on the number of uses, the trend in aluminum and magnesium production in 1944 was characterized by a sharp decline in the production of both metals accompanied by a further accumulation of large Government reserve stocks. Several primary reduction plants were curtailed to prevent building excessive inventories. By the end of the year, however, a lively revival of war production took place when resistance stiffened on the western front in Europe. Production of primary aluminum ingot was reduced from over 90,000 tons per month at the start of the year to 45.000 tons per month by the end of the year.

Jan 1, 1945

By Albert Sauveur

As director of the Division of Metallurgy of the Technical Section of the Air Service, American Expeditionary Forces, from August, 1917, to January, 1919, I devoted much time to the study of the steels best suited to the construction of aircraft. It became apparent at a very early stage of my investigation that the practice of builders varied greatly in regard to the number of different steels to be used, to the kinds of steels, and to their treatment. Some manufacturers employed as many as fifteen steels while the builder of one of the newest motors, favorably passed upon in the United States, assured me that two or, at the most, three kinds of steel were all he needed to produce satisfactory results. In the matter of treatment, the manufacturers were also greatly at variance. Some treated their steel with considerable refinement while others paid but scant attention to this feature. Some manufacturers case-hardened many parts, while others used the case-hardening process sparingly, if at all. Nickel-chromium steels were used at some works for case-hardening while at other plants this treatment was applied exclusively to carbon steels. Air-hardening nickel-chromium steel was used extensively by some and not at all by others. Considerable variance existed likewise in regard to the steels used for admission and exhaust valves. The conclusion was obvious, that no two manufacturers of airplane motors held like opinions as to the steels to be used or as to the treatment they should receive. Was it to be inferred from this that the many committees and associations that had been created, in part at least, for the standardization of aircraft steels had failed to make proper recommendations or that the manufacturers had ignored their recommendations ? Confining our inquiry to the committees and associations that had dealt with this question in England, France, and the United States, it was found that in Great Britain the British Engineering Standards Committee, now the British Engineering Standards Association, had devoted much time to the problem of satisfactory standards for aircraft steels. In April, 1918, this Association presented a set of specifications described as "British Standard Specifications for Aircraft Steels for Government Purchases in the United States of America." They included twenty-one different steels and, as the title indicates, were drawn for the

Jan 1, 1920

By Thomas Fraser, H. F. Yancey

BefoRe a new coal-washing plant is installed, or an existing washery is remodelled and improved, considerable experimental work on the coal to be washed should be done. A thorough examination of a coal, to determine whether it can be washed successfully and the best and most economical process for securing a satisfactory grade of washed coal, calls for mine sampling, analytical work, and experimental coal-washing tests which may require several months' time and the expenditure of considerable money. Having collected the required data on the characteristics of the coal and the results secured with different types of machines under different sets of conditions, it is necessary to decide what method of treatment should be used. The interpretation of the experimental data is no small part of the problem. The first step in the investigative work is to determine from the characteristics of the coal and the manner of occurrence of the impurities whether it is possible to separate the dirt from the coal and produce a washed coal of the required quality. Then it is necessary to select the type of washer or the system of treatment that will produce the greatest amount of washed coal of this grade for the least cost. To secure this information, tests may be made at laboratories operated by consulting or contracting engineers, at the testing plants of machinery manufacturers, at commercial washeries, or in an experimental washery erected on the site of the proposed plant. Such tests will produce figures in which every factor, including analyses of raw coal and washed coal and yield of washed coal, may vary widely. To reduce these results to a common basis for comparison is very difficult. A number of plans

Jan 1, 1923

By Thomas Fraser, H. F. Yancey

BefoRe a new coal-washing plant is installed, or an existing washery is remodelled and improved, considerable experimental work on the coal to be washed should be done. A thorough examination of a coal, to determine whether it can be washed successfully and the best and most economical process for securing a satisfactory grade of washed coal, calls for mine sampling, analytical work, and experimental coal-washing tests which may require several months' time and the expenditure of considerable money. Having collected the required data on the characteristics of the coal and the results secured with different types of machines under different sets of conditions, it is necessary to decide what method of treatment should be used. The interpretation of the experimental data is no small part of the problem. The first step in the investigative work is to determine from the characteristics of the coal and the manner of occurrence of the impurities whether it is possible to separate the dirt from the coal and produce a washed coal of the required quality. Then it is necessary to select the type of washer or the system of treatment that will produce the greatest amount of washed coal of this grade for the least cost. To secure this information, tests may be made at laboratories operated by consulting or contracting engineers, at the testing plants of machinery manufacturers, at commercial washeries, or in an experimental washery erected on the site of the proposed plant. Such tests will produce figures in which every factor, including analyses of raw coal and washed coal and yield of washed coal, may vary widely. To reduce these results to a common basis for comparison is very difficult. A number of plans

Jan 1, 1923

By Keats, J. L.

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical charac- teristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained.

Jan 1, 1957

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential, but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for converting a prospect into a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is usually headed by an engineer-promoter or an entrepreneur trader who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the ha1 operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1964

By J. Chipman, M. N. Dastur

The importance of dissolved oxygen as a principal reagent in the refining of liquid steel and the necessity for its removal in the finishing of many grades have stimulated numerous studies of its chemical behavior in the steel bath. From the thermodynaniic viewpoint the essential data are those which determine the free energy of oxygen in solution as a function of temperature and composition of the molten metal. A number of experimental studies have been reported in recent years from which the free energy of oxygen in iron-oxygen melts can be obtained with a fair degree of accuracy for temperatures not too far from the melting point. Certain discrepancies remain, however, which imply considerable uncertainty at higher temperatures; also several sources of error were recognized in the earlier studies. It has been the object of the experimental work reported in this paper to reexamine these sources of uncertainty and to redetermine the equilibrium condition in the reaction of hydrogen with oxygen dissolved in liquid iron. The reaction and its equilibrium constant are: H2 (g) + Q = H2O (g); K1 _ PH2O / [1] Ph2 X % O Here the underlined symbol Q designates oxygen dissolved in liquid iron. The activity of this dissolved oxygen is known to be directly proportional to its concentrationl,2 and is taken as equal to its weight percent. The closely related reaction of dissolved oxygen with carbon monoxide has also been investigated:3,4,5 co (g) +O = CO?(g); K _ Pco2___ [2] K2= pco X % O [2] The two reactions are related through the wat,er-gas equilibriuni: H2 (g) + CO2 (g) = CO (g) + H2O (g); K2 = PCO X PH2O [3] PH2 X PCO2 and with the aid of the accurately known equilibrium constant of this reaction, it has been shown5 that the experimental data on reactions [1] and 121 are in fairly good, though not exact, agreement. Experimental Method Great care was taken to avoid the principal sources of error of previous studies, namely, gaseous thermal diffusion and temperature measurement. The apparatus was designed to provide controlled preheating of the inlet gases and to permit the addition of an inert gas (argon) in controlled amounts, two measures found to be essential for elimination of thermal diffusion. A known mixture of water vapor and hydrogen was obtained by saturating purified hydrogen with water vapor at controlled temperature. This mixture, with the addition of purified argon, was passed over the surface of a small melt (approximately 70 g) of electrolytic iron in a closed induction furnace. After sufficient time at constant temperature for attainment of equilibrium the melt was cooled and analyzed for oxygen. GAS SYSTEM A schematic diagram of the apparatus is shown in Fig 1. Commercial hydrogen is led through the safety trap T and the flowmeter F. The catalytic chamber C, held at 450°C, was used to convert any oxygen into water-vapor. A by-pass B with stopcocks was provided so that the hydrogen could be introduced directly from the tank to the furnace when desired. From the catalytic chamber the gas passed through a water bath W, kept at the desired temperature by an auxiliary heating unit, so that the gas was burdened with approximately the proper amount of water vapor before it was introdvced into the saturator S. All connections beyond the catalytic chamber were of all-glass construction. Those connections beyond the water bath were heated to above 80°C to prevent the condensation of water vapor. After the saturator, purified argon was led into the steam-hydrogen line at J, and finally the ternary mixture was introduced into the furnace. THE SATURATOR The saturator unit comprised three glass chambers, as shown in Fig 1, the first two chambers packed with glass beads and partially filed with water and the third empty. Each tower had a glass tube with a stopper attached for the purpose of adjusting the amount of water in it. The unit was immersed in a large oil bath, which was automatically controlled with the help of a thermostat relay to constant temperature, ± 0.05ºC, using thermometers which had been calibrated against a standard platinum resistance thermometer. The performance of the saturator over the range of experimental conditions was checked by weighing the water absorbed from a measured volume of hydrogen; the observed ratio was always within 0.5 pct of theoretical.

Jan 1, 1950

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st'ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.'-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5'6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964