Search Documents

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By R. H. King

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. So far, we have developed and reported on algorithms that automatically produce accurate time-study reports of continuous miner data from kilowatt sensors at the Deserado Mine, and we are extending the system to accept other types of sensor data input. This paper focuses on AI techniques that improve accuracy of the numerical algorithms in the PRS module. Additional AI work for the KRS module is summarized in this paper.

Jan 1, 1989

By S. R. Maynard

The Ortiz Mountains lie 25 mi (40 km) northeast of Albuquerque, New Mexico in Santa Fe County (Figure 1). Approximately 350,000 ounces (11,000 kgs) of gold have been produced from the Ortiz Mountains since the 1820s. The 100 square mile (260 square km) Ortiz Mine Grant was secured from the Mexican government in 1833 by Jose Francisco Ortiz for the purpose of mining gold. The Grant has remained more or less intact to the present. The mineral rights are currently owned by Ortiz Mines, Inc. of Joplin, Missouri and are leased to LAC Minerals, USA, Inc. (west half) and to Gold Fields Mining Corporation (east half).

Jan 1, 1989

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

By Werner Bilfinger, Claudio Nahas, Marcelo Waimberg

"INTRODUCTION The so called Porto Maravilha Project consists of the re-urbanization of a 500 ha area in the Rio de Janeiro port region. Several changes in local infrastructure are being implemented, including a significant change in the road system, with the demolition of the former “Via Perimetral” viaduct and construction of 4 new tunnels: • Saúde tunnel - 35 m long (Waimberg et al, 2014); • “Binária tunnel” - 1012 m long; • “Via Expressa” twin tunnels - 1850 m long each way. The tunnels were excavated almost completely in rock using conventional drill and blast methodology and only some short stretches in weathered rock, associated to faults zones, residual soils and marine sediments close to the tunnel portals. During excavation of access shaft and “Via Expressa” and “Binária” tunnels significant ground settlements as well as settlements of buildings founded both on shallow and deep foundations were measured. These values could not be associated to conventional tunneling induced settlement troughs. This paper focuses on the “Via Expressa” tunnels, presenting a brief description of the project as a whole, its geological and geotechnical background, monitoring results, and a discussion of possible causes of the measured settlements. PROJECT DESCRIPTION The Porto Maravilha Project is an integrated multidisciplinary action on behalf of the Rio de Janeiro city council with support from the State and Federal Governments. In addition to creating new conditions for working, housing, transport, culture and leisure for the resident population, it also promotes expressive economic development in the region (Portonovo, 2015). Porto Maravilha Project is carrying out actions for the recovery of the region’s historical heritage, as well as promoting the population´s social and economic development. One of the main benefits of the Porto Maravilha Project is the construction of the new traffic system in the port area, consisting of the Express and Binário roadways. The new project, which will replace the current Perimetral Rodrigues Alves viaduct system, will increase traffic flow capacity by 27%."

Jan 1, 2016

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.'s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By L. A. Roe

The year 1867 marks the first year of commercial production of phosphate rock in the United States. South Carolina produced almost all of the domestic output of mineral phosphate until phosphate mining began in Florida in 1888. During the period 1868 to 1949 the total marketed production of domestic phosphate rock was about 186 million long tons of which 71.5 percent was produced in Florida, 18 percent in Tennessee and 7 percent in South Carolina (1). From 1949 through 1960, Florida phosphate rock production has ranged Prom 71 to 77 percent of the total domestic production. Since three-fourths of the domestic phosphate production is from the Florida field, and since most of the phosphate from the Tennessee and Western fields is not processed, but used directly as electric furnace burden, this paper will concern itself almost entirely with water requirements for mining and processing ore from Florida. Figure 1 summarizes phosphate rock production for Florida vs. total United States production over the period 1947-1960.

Jan 1, 1962

By J. C. Motz

During the past five years, Rexnord has developed, tested and introduced the Nordberg Omnicone Crusher to the industry. When the Symons brothers invented the cone crusher over 60 years ago, they employed the principle wherein the length of the crushing stroke was related to the free fall of material by gravity. This permitted the material being crushed to fall vertically in the crushing chamber; and in effect, caused the particles to be crushed in a series of steps or stages as the particles got smaller due to the crushing action. This also helps to reduce the rate of wear of the liners since the sliding motion of the particles is minimized.

Jan 1, 1986

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By X. Cai, L. Jiang, G. Fu

A process for recovering manganese from low-grade manganese oxide ore through a reduction acidolysis-selective leaching method is investigated. Two types of biomass, sawdust and straw, were used as reductants. Reduction acidolysis, using concentrated sulfuric acid, was used to disrupt the structure of the biomass, allowing the biomass to be hydrolyzed into monosaccharides. Analysis by X-ray diffraction revealed that Mn2O3 was reduced to MnSO4. Then, in the selective leaching process, iron was removed through the formation of goethite. The optimized experimental parameters are as follows: reductant to ore mass ratio of 0.4, sulfuric acid to ore mass ratio of 0.9, water to ore ratio of 0.5, aging time of 18 h, leaching temperature of 95 °C, leaching time of 90 min, and solution pH of 2.5 to 2.8. Under these conditions and using sawdust as the reductant, the manganese leaching efficiency and iron removal efficiency were 91.8 and 99.2 percent, respectively.

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Harrison R. Cooper

The expanding use of digital control in the metallurgical industry is a significant recent development. From 1970 to 1975, approximately forty metallurgical plants throughout the world have adopted automation techniques based on digital controls (see Table 1). Several recent technical reports have described development of digital control systems in concentrator grinding control, 1,2 flotation,3 and smelter operations.4,5

Jan 1, 1975

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. Saki, J. F. Brune, J. W. Grubb

"Researchers at the Colorado School of Mines have studied the influence of headgate side ventilation controls near the longwall start-up room on the formation of explosive gas zones (EGZs) in underground coal longwall bleeder ventilated gobs. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) researchers developed a Computational Fluid Dynamics (CFD) model to study the formation of methane-air mixtures in the gob, start-up room, and bleeder entries. The relative change in size and location of EGZs are examined in response to ventilation controls in the headgate side bleeder entries near the start-up room. Modeling suggests that adjustments to the ventilation controls can be made to minimize the size of the EGZ. However the EGZ may form in or around active working areas regardless of the ventilation control settings. Research found regulators on the crosscuts into start-up room and first entry inby can force air into to crosscuts outby the start-up room causing more air to flow through the gob. INTRODUCTION Underground longwall mine ventilation systems may operate with either a bleeder ventilated gob or a progressively sealed gob. Bleeder ventilated gobs must meet the standards for safe operation of the bleeder system by examining bleeder system effectiveness. As defined in the United States Mine Safety and Health Administration (MSHA) Program Policy Letter (PPL) No. P13-V-12 (MSHA 2013), the pillared area or gob is “any area where a reduction in pillar size has occurred during retreat mining” and includes the “caved and broken material, the interstices within the caved material, and the open spaces surrounding the caved material.” The PPL further states that the intended purpose of ventilating the gob is “to protect active workings from the hazards of methane accumulations …” The requirements for operating a bleeder system as stated in The United States Code of Federal Regulations (CFR 2013) Title 30 §75.334(b) is to pass ventilation air though the gob “and to continuously dilute and move methane-air mixtures [from the gob] away from active workings and into a return air course …” where the concentration cannot exceed 2 percent methane (CFR 30 § 75.323). Further clarification of the bleeder system as described in the PPL states the following: “A bleeder system includes the area from which pillars are wholly or partially recovered, bleeder entries, bleeder connectors, and all associated ventilation control devices that control the air movement through the area. Bleeder entries are air courses designed and maintained as part of the bleeder system.”"

Jan 1, 2015

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By G. Plenge, M. Brittan

"Plant design parameters for gold extraction, leach residence time and cyanide consumption are generally determined from standard bench-scale bottle roll or agitation leach tests. The application of laboratory data to process design has essentially evolved from the testing of oxide or low cyanide-consuming ores. Such scale-up factors may not be appropriate for ores that deplete cyanide and oxygen since this interferes with gold extraction kinetics. High cyanide-consuming ores also exacerbate the differences between the conditions applicable to small batch tests and large continuous operations. Testing a reactive high-sulfide South American ore deposit necessitated the re-evaluation of conventional bench-scale cyanidation procedures. Pulp density can be a major factor affecting the results for plant design purposes and should be treated as a test work variable. As with high clay-bearing ore, where pulp viscosity can hinder mass transfer, minimizing the influence of test equipment on gold extraction kinetics may require low pulp densities. This introduces interpretative complexity since cyanide consumption changes as a function of pulp density. Activated carbon also consumes cyanide, so its effect has to be accounted for in the case of carbon-in-leach (CIL) or carbon-in-pulp (CIP) plant flowsheets. Since cyanide is an expensive reagent, often a major component of plant operating costs, it is important that the scale-up of cyanide consumption from laboratory to plant be representative. The traditional method of reporting cyanide consumption in bench-scale testing is questioned since it takes credit for residual free cyanide in leach tails. The projected plant consumption may be better estimated by using the total cyanide addition in a laboratory test. We propose a test work protocol that categorizes the cyanide consumption into its components but requires more extensive testing to generate design data. The ultimate validation of scale-up factors used by project engineers requires rigorous bench-scale versus commercial plant comparative data. Such data are not readily available.IntroductionMajor factors in the design of a gold processing plant are gold recovery, leach residence time and cyanide consumption. These parameters are important determinants of project revenue and costs and, thereby, potentially of project financial viability. Estimates of the associated design criteria for a commercial plant are normally generated from laboratory cyanidation, carbon-in-leach (CIL) or carbon-in-pulp (CIP) tests using standard procedures (Angove, 2005). The key question is whether the standard laboratory test work procedures developed historically for low reagent consuming ores are appropriate for ores that are highcyanide and oxygen consumers.The present paper examines test procedural factors that can influence the test work results and, therefore, their interpretation for design scale-up purposes. The study refers in particular to a high cyanide-consuming sulfide ore. The ore was being tested to develop scoping level engineering design criteria for a proposed project in South America."

Jan 1, 2015