Search Documents

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By Tracy Brettmann

In recent years the Augered Cast-In-Place (ACIP) Pile industry has seen a substantial increase in the quality control options available to Contractors, Engineers, and Owners. Quality control methods range from the simple, manual techniques that have been used for years to new computerized installation monitoring equipment and nondestructive testing methods. Our ability to monitor and test ACIP piles has grown to such a degree that the industry is struggling to determine how much quality control is enough. This paper reviews the many options available and describes the pros and cons of each. The various nondestructive testing methods, in particular, have been difficult to apply reliably due to misapplications of methods and misinterpretation of the results. ACIP piles have unique properties that require the various nondestructive testing methods available be considered very carefully in determining the method most appropriate for a particular use. Some nondestructive testing methods, as well as automated monitoring equipment, potentially can be applied effectively to increase the level of quality control for ACIP piles. The experience gained on real projects using these new methods, in conjunction with the old procedures, provides valuable information for future applications.

Jan 1, 2000

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2004

By Mark R. Svinkin

Construction-induced vibrations may be detrimental to adjacent structures and sensitive electronics operating nearby. Construction vibration sources have a wide range of energy and velocity, as a function of time, transmitted on the ground. Analysis of existing methods for predicting ground and structure vibrations shows that empirical equations provide calculations only of amplitudes of vertical soil vibrations with insufficient accuracy. This paper presents the application of the impulse response function concept to solve the geotechnical problem of predicting ground and structure vibrations before installation of vibration sources. Impulse response functions reflect real behavior of soil and structures without the investigation of soil and structure properties. A procedure is presented to compute predicted ground and structure vibrations. Good agreement is found between predicted and measured records.

Jan 1, 1999

By Hyu-Soung Shin

This study is concerned with the characteristics of the behavior of steel-concrete composite drilled shafts, a material that is used for large bridge foundations, and especially for weak submerged ground conditions. Depending on the loading or boundary conditions considered, the behavior of foundation will vary. The bearing capacity of steel-concrete composite drilled shaft is influenced by initiation and propagation of fractures along the interface between steel casing and filled concrete. The interface effect is taken into account with the following two simplified cases: (1) detached model with free interface (no shear stiffness of interface) between concrete core and steel casing, (2) confined model by an upper steel cap with free interface. In the confined model, it is intended to have an unified behavior of composite shaft between concrete core and steel casing but there is interface between them. Intensive numerical studies have been undertaken to investigate detailed behavior of the composite shaft. In this study, 3-D finite element analysis is employed. Ground conditions typical of those encountered for the design of drilled shaft under water are considered affecting the behavior. Also, an attempt is made to generate possible combinations of the loads which have been considered in fields. Detailed characteristics of the stress and displacement distributions are evaluated to understand the mechanisms of composite shafts.

Jan 1, 2007

By Michael Arnold, Bob Faulhaber, Joe Nichols

"Center Hill Dam is a critical part of the infrastructure controlling floods at the Caney Fork River and reducing flood levels at the Cumberland, lower Ohio and Mississippi Rivers. The Center Hill Dam Foundation Remediation Project was necessary to address Karst features in the foundation rocks and observed signs of distress of the dam. From 2011 to 2014 BAUER Foundation Corp. (BFC) performed deep foundation works for this project. The executed features of work include the installation of two walls. The first wall extends throughout the clay embankment into the underlying rock to provide encasement during the construction of the second wall. Its width of 7.4 feet makes it the widest diaphragm wall ever installed. The second wall is the actual seepage barrier and provides a continuous 2- feet wide wall. It extends through the first wall into the underlying rock and is up to 300 feet deep. The paper introduces the project, the requirements specified by United States Army Corps of Engineers (USACE) for encasement and barrier wall and the approaches taken by BFC. It discusses the ground conditions and describes the excavation equipment as well as the excavation methods used. A special focus is put on the steering capabilities of the hydrocutter equipment and the verticality performance.PROJECTBeginning in 2011, BFC was tasked by the USACE with the installation of a seepage barrier/cutoff wall at the Center Hill Dam Foundation Remediation project under a partially performance based specification. The remediation was necessary due to karst features in the foundation rocks and observed signs of distress, which led USACE to rate the dam with the most critical dam safety action classification (DSAC I). The executed features of work include the installation of two walls. The first wall, an encasement wall, extends vertically through the clay embankment and is embedded minimally into the underlying bedrock to provide embankment stability during the construction of the second wall, the barrier wall. The encasement wall is constructed of overlapping panels 7.4 feet (2.25 m) wide, which is the widest diaphragm wall ever installed, and up to 210 feet (64 m) deep. The second wall is the seepage barrier and provides a continuous 2 feet (0.6 m) wide wall consisting of overlapping panels. It extends through the encasement wall into the underlying bedrock and is up to 307 feet (93 m) deep. BAUER BC40 and BC50 hydrocutters mounted on MC96 and MC128 foundation cranes were used to perform the majority of the works (Figure 1). Excavations were performed under bentonite slurry (encasement wall) and water (barrier wall) and concrete was poured with the tremie method. Adding to the challenges, the project had to be executed in an environmentally sensitive area. Based on the high risk, a special focus was put on monitoring, quality control and geometric accuracy. The WallTracker information management system was used to share all relevant data between BFC and USACE (Roff et al. 2014)."

Jan 1, 2017

Jan 1, 1989

By Sanjeev Malhotra

The American Petroleum Institute (API) method of predicting pile capacities in sands is reviewed. Factors that influence pile capacity such as soil parameters, pile parameters, loading effects and installation effects are listed. In addition, the simultaneous occurrence of physical phenomena such as grain crushing, pile shaking, stress-redistribution and plugging add to the uncertainty in the prediction model. To better understand the method of prediction, each parameter and the associated uncertainty is revisited. It is evident that these factors are inter­related and sometimes compensating. This discussion also draws attention to the influence that pile installation procedures can have on pile capacities and highlights the need for field experience with various pile installation procedures for designers. In summary, the strength of the method lies in its simplicity and ease of application, but the possible savings generated by an improved method are too substantial to ignore.

Jan 1, 2000

By George K. Burke

Single axis soil mixing is a mechanical method of blending soil in situ with a reagent binder to achieve improved character. Generally this achieves a design compressive strength or shear strength and/or permeability, but can be used to immobilize and/or fixate contaminants as well as a treatment system for chemical reduction to a more "friendly" substrate. The reagent binder can be a variety of materials, including cement, fly ash, slag, lime, and an assortment of additives. Usually this reagent is delivered in a slurry form (combined with water), but the Dry Mix Method uses pneumatic conveyance.

Jan 1, 2001

By C. Y. Liu

This paper principally deals with the application of caisson foundation in the Chinese bridge building industry, the different types of caisson foundation adopted, and their spheres of application. Caisson foundation has been used and speedily developed for bridge works in New China, and a number of new innovations have been made in its design. Especially in deep water foundation, the Nanjing Bridge over Changjiang has attained one of the deepest bridge foundations in the world. There are six types of deep caisson foundation being now in use in China, namely:

Jan 1, 2010