Search Documents

By M. Maley, S. Burling, R. Ring

ABSTRACT The numerous global uranium deposits vary significantly in mineralogy, grade, and textural characteristics; therefore, information from traditional (or conventional) sources on the fundamentals of leaching uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies can be effective in understanding leach systems and can lead to improvements in process design but there remains a lack of fundamental understanding necessary for ongoing process optimization as ore bodies continue to vary. ANSTO Minerals has undertaken a work program to address several fundamental questions about uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Jan 1, 2012

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By M. Cossette, P. C. A?tcin

At present there is considerable confusion in the asbestos industry with regard to density and porosity measurements of asbestos. In order to clarify the situation, various notions of porosity and density are defined by means of simple schemes and clear symbols are proposed to denote them. An experimental procedure is then preposed and outlined, which is based upon Archimedes' principle. Experimental conditions at each stage of the method are explained clearly in order to minimize the opportunity for errors. Finally, the results of a study on the porosity and density of asbestos minerals having various characteristics are presented.

Jan 1, 1972

By Jehan Rondot, Raymond Marleau

"Des quartzites trés pars ont été découverts au cours de la cartographie de la region du lac des Martres, étape de l'étude géologique de la region de Charlevoix.On distingue quatre groupes métasédimentaires, tons con tenant des niveaux de quartzite dans an mains deux domaines géologique différents, c'est à l'ouest, clans le do¬maine gneisso-charnockitique que se situent les quartzites du groupe des Martres. Quartzite et gneiss à, grenat et sillimanite, en banes épais, constituent la formation de La Galette. A Pest, dans un environnement gneisso-granitique, les deux groupes métasédimentaires de Saint-Siméon, et de La Malbaie comprennent, par contraste, des bancs pen épais et de compositions variées. Les niveaux de quartzite dépassent rarement 50 m d'épaisseur. L'autre groupe métasédimentaires, celui de Saint-Tite des Caps, recoupé de nombreuses intrusions charnockitiques et granitiques, ne possède que de minces niveaux de quartzite.La pureté et la grande épaisseur des quartzites de La Galette suppose une histoire complexe qui se termine par des depots continentaux de climat aride, par opposition aux depots marins des autres groupes. D'autre part, la presence de ces quartzites an sein de roches Presque anhy¬dres et de haute temperature que sont les charnockites leur confére des caractéristiques de fusion sans decrepitation.Parmi la multitude de depots de quartzite qui existe clans le monde, peu sont de qualité supérieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement à ceux des meilleurs gisements des Etats-Unis, de l'Europe de l'Ouest et de l'Afrique du Sud. D'accès facile pour l'exploitation, les gisements ne sont qu'à une trentaine de milles de Baie Saint-Paul ou de La Malbaie, sur le Saint-Laurent.L'utilisation en metallurgic prévue pour le quartzite de La Galette comprend la production de silicium, de ferro¬silicium et d'autres alliages de silicium. La composition du quartzite est en outre appropriée pour la production de carbure de silicium et de silicate de sodium. Les fines peuvent être utilisées pour la fabrication du verre et comme matiere de charge"

Jan 1, 1977

By P. Cicmanec

Mining activities in the territory of Slovakia have a long history. Mining techniques have developed rapidly in the last centuries. This paper deals not only with mining history, but also with underground brown coal mining, magnesite mining and other mining activities at present and sustainable developments of the mining industry in the Slovak Republic. This paper looks forward in the context of mineral raw materials in Europe (Global Europe, 2012).

Aug 1, 2013

By G. W. MacLeod

The iron ore question in this country has been widely discussed for many years, but only recently has its real significance becoming generally understood. The exhaustion of the old Helen mine, in 1918, marked the last phase of hematite production in Ontario, and with the closing of the Magpie mine in 1921 , Canada ceased to be a producer of iron ore. For the past three years every ton of ore used in Canadian blast furnaces has been imported. In a recent issue of the Engineering and Mining Journal-Press, Arthur B. Pearsons, Assistant Editor, makes the following statement : Iron dominates the world. Some contend that coal is more vital. be-cause heat is needed to make iron and steel. But there are other sources of energy, more convenient and less costly and it is only a question of time when progress in hydro-electric development will have reached the point where coal will be but an incidental source of power and heat. Even more direct means than the generation of electricity by hydro-power eventu-ally will be developed by making available the latent energy of the sun. But iron; Science gives not the vaguest suggestion that anything will dis-place iron and steel as the most essential material tool of modem civiliza-tion. ? Hardness, tenacity, malleability-it possesses all these in unique de-gree. These are some of the qualities that make steel and iron indispensable in modern industry. The domestic consumption per inhabitant of the United States has climbed uniformly from 0.18 tons in 1900, to 0.36 tons in 1922. New kinds of machines and new types of structures are being devised every year; and steel or iron is the basis of most of them." It is unlikely that the Ontario Government were actuated by this motive when they appointed the Iron Ore Committee to investigate and report on the iron ore situation, nevertheless, these facts must have influenced them in some degree.

Jan 1, 1924

By Steve McMullan, Blaine Webster, Ian Johnson, Ron Matthews

"Time domain spectral Induced Polarization (IP) data from the Tower, Jojay and Laurel Lake gold deposits in northern Saskatchewan are presented. The resistivity data shows both resistivity lows (due to fault, shear or alteration zones) and resistivity highs (due to silicification) in the area of the deposits. The high resistivity zones suppress and distort coincident IP responses, calling f or high quality surveys and special care in interpreting the IP data.Electromagnetic methods are not effective in locating the deposits. This is due, in part, to masking by conductive cover. The Jojay Lake deposit has a strong magnetic response. A more indirect magnetic association is seen for the Tower Lake deposit. The Laurel Lake deposit has no magnetic signature. Magnetic data are useful in defining structure in all cases.All three deposits are outlined in the IP survey results. IP anomaly amplitudes from the pole-dipole array are from two times (Tower and Laurel Lak e) to six times (Jojay Lake) background values. Gradient array IP anomalies are of less amplitude. The spectral time constant is short for the Tower and Laurel Lak e deposits and long for the Jojay deposit. This implies that the metallic sulphides in the Jojay deposit are more interconnected than those of the other two deposits. INTRODUCTIONInduced polarization / resistivity surveys are commonly used in gold exploration program s in the Canadian shield because the IP method is effective in detecting disseminated metallic sulphides which are often found associated with gold. Other common geophysical sur vey methods such as magnetics, VLF and EM are not generally capable of direct detection of disseminated sulphides. Since the introduction of the IP method in the 1950s, it has undergone continuous improvement. The most recent improvement is the development of time domain receiver s which sample the full de cay and record it in digit al form. This results in a more complete measurement of the response which permits analysis and enhancement of data quality and the derivation of a nomaly parameters which characterize the measured decay. This extension of conventional time domain IP methods is called spectra l IP, a term first introduced by Pelton et al. working in the frequency domain Spectral IP surveys are attractive because they allow the possibility of discriminating between IP responses which have similar amplitudes but are due to dissimilar geo logic targets. The discrimination can be important in the selection of IP anomalies for follow-up.Time domain spectral IP survey results are presented over three known gold deposits in northern Saskatchewan-Tower Lake, Jojay Lake and Laurel Lake. The surveys were initiated and supported by Cameco-A Canadian Mining and Energy Corporation (formerly the Saskatchewan Mining and Development Corporation-SMDC) and were carried out by JVX Limited using the Scintrex IPR-II receiver and attendant spectral analysis software."

Jan 1, 1989

By Janos de Warga

"After a short introduction to the history of the semi-conductor theory, the paper describes the principles of electron and hole flow in the semiconducting materials, the operation of the PN junction, and the rectification process in multi-layer devices (diodes and SCR's). The various methods of purification and zone-refining of the silicon are illustrated prior to the discussion on the most commonly used junction-forming processes (alloying, diffusing, etc.). Modern device fabrication and packaging operations are illustrated. Factory testing, evaluation, electrical parameters and guaranteed rating characteristics are listed. It is explained in this paper how the various device parameters affect the electrical performance of the finished unit and how the finished unit characteristics (turn-on, turn-off time, etc.) will influence the equipment rating. In concluding, some typical items of equipment are highlighted, and the applications of these semiconductor rectifiers in the chemical, mining, pulp and paper, and steel industries, etc., are dealt with."

Jan 1, 1967

By Naoki Takada, Dae-Sung Cheon, Minoru Sato, Masaji Kato, Manabu Takahashi, Weiren Lin

"The permeability and specific storage of rocks and sedimentary layers deep underground are critical parameters for issues related to the buried evaluation of natural gas and oil, CO2 aquifer storage, various kind of waste storage and so on.The Shirahama sandstone of the Wakayama prefecture, Kii peninsular in central Japan, consists mainly of quartz grains with no cracks and rock fragments that are aggregations of various kind of minerals. The quartz grains have an average size of about 150 micron. The pre-existing pore sizes were distributed dominantly at approximately 1 micron, and the total porosity was about 13%.During the hydrostatic compression test, we measured permeability of Shirahama sandstone by Transient Pulse test for three mutually perpendicular directions. Permeability of Shirahama sandstone remained fairly constant while increasing the effective confining pressure. Permeability anisotropy was observed slightly in the normal and two parallel directions to the bedding planes.We used micro focus X-ray CT with high resolution of 10 micron to visualize and measure the voids space information in Shirahama sandstone. Three-dimensional data were obtained in the intact and stressed sandstone simultaneously. Pore structures and grain boundaries were clearly distinguished. Pore closure and grain movement were clearly observed with increasing confining pressure. Micro focus X-ray CT is an effective tool to visualize and measure the geometrical information in rocks.Three-dimensional medial axis (3DMA) method was introduced to quantify the flow-relevant geometric properties of the voids structure in Shirahama sandstone using µfocus X-Ray CT data. The number of connecting path between two faces, tortuosity and the shortest path distribution within an arbitrary region of Shirahama sandstone specimen were analyzed. Geometrical information on the number of connecting path shows reasonable correlation between permeability anisotropy and mutually perpendicular directions normal and parallel to bedding planes. In addition, we introduced numerical simulation of fluid flow of pressurized Shirahama sandstone by LBM, to discuss the permeability change caused by pressurization on effective confining pressure. We obtained the detailed distributions of fluid pressure and fluid velocity in relatively narrow voids space more than 10 µm. It was confirmed that pressurization effect on permeability caused by the decrease of the connecting path and the shortest path between arbitrary faces, and then caused a complex condition on fluid pressure and fluid velocity."

Jan 1, 2015

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By Malcolm Scoble, Nick Vagenas, Greg Baiden

Recent advances in underground communications technology have demonstrated the feasibility of teleoperation and automation in underground metal mines. One major challenge lies in the automation of underground mobile machines from surface, with the potential to reduce significantly the need for human involvement in underground operations. This paper reviews the evolution of underground metal mining automation, principally related to the development of teleoperation and automation of mobile mining machines. Examples of prototype systems are given and the associated benefits that have been observed are reviewed.

Jan 1, 1997

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By The Staff

THE gold mining industry in Canada is today the most important stabilizing influence in the country. This factor was brought out particularly during the 'depression' years, when steady employment was given to men in that industry and the monies spent in supplies and power in turn benefited the country to a great extent. At the same time, a commodity was produced which was saleable in any market of the world, thus maintaining Canada's credit in foreign markets and keeping her trade balances equalized. We have a vast area known as the Precambrian Shield. The agricultural possibilities of this area are practically negligible and it will depend entirely upon the mineral and forest resources to make this district an economic factor in the life of Canada. To date, from the mineral point of view, we have been highly successful. There are, however, still vast areas to be explored. It is tedious and laborious work, entailing great individual hard-ships and the expenditure of much energy and money. During my thirty years' experience in the search for, and operating of, gold mines, I have come to the conclusion that although individuals may give all their time, energy, and money, Governmental assistance is absolutely necessary in the development of hydro-electric power sites and roads. The Governments, to date, have given splendid co-operation along these lines, but in order that this great industry may go ahead they should continue their good work and, if possible, give greater relief from taxation to mines situated at a considerable distance from the railway.

Jan 1, 1938

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"In natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the content of MoO3 varies from 2% to 10%. As a result, the flotability of seyrigite (scheelite with molybdenum) turns to be weaker. One seyrigite mine, which has been built for 3 years,still could not produce qualified seyrigite concentrate due to the weak flotability of seyrigite (Mo-bearing scheelite) in raw ore. In our experimental research, through adopting new seyrigite collector TA-3 and advanced mineral processing technology, the seyrigite concentrate with a grade of 65.62% WO3 at a recovery of 87.47% was obtained for the raw ore containing 0.19% WO3 and 0.074% Mo. By applying the new technical achievement, for the raw ore containing 0.272% WO3, the seyrigite concentrate assaying 68.03% WO3 with a recovery of 77.56% was obtained in industrial production.INTRODUCTIONIn natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the scheelite is changed to be seyrigite (Ca[(W,Mo)O4]) (Ma, Bian, & Wang, 2013). The content of MoO3 in seyrigite varies from 2% to 10% usually, the content of MoO3 in some of the seyrigite even reaches 34%. The flotability of seyrigite is weak (Zhang, 2007), and the seyrigite is difficult to be recovered by flotation with common collectors and regulators. One scheelite mine in Anhui China, which is a skarn type seyrigite mine, has not produced qualified concentrate yet since 3 years it has been built due to the limit of beneficiation technology. Therefore, it is necessary to conduct research on the collectors with high efficiency and developing advanced processing flow for this kind of ore."

Jan 1, 2016

By J. Fournier, D. Fortin, F. Robichaud

Since milling began in 1988, the Laronde mill has been expanded several times, the most recent, increasing the milling rate from 5 000 to 7 000 mtpd. Laronde uses SAG/ball mill grinding followed by copper and zinc flotation circuits. A cyanidation/Merrill-Crowe process recovers the remaining gold and silver in the flotation tails in order to cope with high silver/gold ratio associated with the discovery of the Penna shaft. Since the commissioning of the Merrill-Crowe refinery in 2000, several modification and expansion projects were performed to reduce health and safety hazards. Remarkably, several of these improvements have contributed at increasing productivity and Net Smelter Return of the refinery while reducing worker's injuries. In 2004, the refinery was audited to evaluate and quantify the circuit performance. Metallurgical and mechanical operating conditions of the refinery are now understood and areas for further improvements are well defined. This paper describes some of the factors that have contributed to this improvement and describes how ergonomics and recovery can further be improved.

Jan 1, 2005

By B. Jin

Removal of fluoride and chloride by alkaline washing from direct lead smelting dust which originated from an Ausmelt furnace is reported. The results show that the fluoride removal efficiency increases with an increase of alkaline concentration, alkaline washing temperature and time. The L/S ratio has little effect on fluoride and chloride removal efficiency. A new flow sheet for removal of fluoride and chloride from the dust was successfully proposed according to the results. Fluoride and chloride removal efficiencies are more than 53.68% and 63.18% respectively using the flow sheet under the optimum parameters of temperature 338 K, L/S ratio 3:1 and alkaline washing time of 1.5 h. The contents of fluoride and chloride in the alkaline washing residues can meet the standard of zinc purity as hydrometallurgical materials for zinc processing.

Jan 1, 2014

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007