Search Documents

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

By J. Boldy

This paper is an attempt to place Canadian Precambrian volcanogenic deposits in perspective, by examining and compiling data regarding certain neglected fundamentals of size, grade, value, frequency distribution and spatial density. The discovery roles played by various exploration methods are compared and contrasted, and. using empirical methods, the probabilities of discovery are discussed, combined with the use of an effective 'cost-per-target' program. From these basic observations, realistic exploration judgments may be made. Using similar methodology, this format may be applied to other types of deposits. Precambrian volcanogenic deposits occur in a natural geometric progression in size. They number 110, of which 70% are pre-producers, producers or past-producers. These deposits are bonanzas and generally have a 'net pre-smelter' value of between $43 and $62 per ton. The statistically typical deposit is that which occupies the modal position, has 400,000 tons of ore, a value of $20 million and occurs with a frequency of 40%. A median deposit has 1.4 million tons of ore, a value of $70 million and occurs with a frequency of 15%. An upper-decile deposit ha s 13.3 million tons of ore. a value of $750 million and occurs with a frequency of 6.5%. The major, mid-upper-decile deposits have a minimum of 50 million tons of ore, a value of $3 billion and occur with a frequency of 4%. Five major volcanogenic deposits occur in the Precambrian and account for 54% of production. This contrasts with 55 deposits (all below the median) which account for 3.9% of production.

Jan 1, 1977

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

By A. Eltringham

Operations downstream of mining and beneficiation are still being subjected to increasing scrutiny as highly capitalized projects have been either slow to achieve their targets or have actually failed to do so. Leaching and smelting projects have fundamentally high calls on capital and technology as reaction rates are increased and the capture and disposal of unwanted products are subjected to greater restrictions. Separating value from waste inherently becomes riskier as the purification of the desired product imposes greater demands on the process to produce benign wastes. When we superimpose on the chemistry of the project severe predictions of throughput rates, that bring in facets of manufacturing, we are introducing complexities that the records show are not handled well. This paper discusses some of the more common challenges that operators face and what methods are available and are likely to be successful in preventing the loss of value as projects are brought on-stream. This thinking needs to start much earlier and at greater intensity than our industry has normally chosen to employ.

Jan 1, 2011

By V. A. James

The new electrolytic copper refinery situated at Copper Cliff, Ontario, has been in operation for over a year and a half. This plant is operated by the Ontario Refining Company, Limited. The associated companies behind the enterprise are the International Nickel ?company of Canada, Limited, the American Metals Company, Consolidated Mining and Smelting Company of Canada, Limited, and Ventures, Limited. The plant was an outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as compactly as possible. Starting anode furnace operations in June, 1930, and electrolytic refining on July 1st of that year, after a record-breaking construction programme completed in only fifteen months, the plant soon settled into its stride and the usual starting-up difficulties were .rapidly overcome. The rated capacity of the plant, namely, twenty million pounds of refined copper per month, has, of course, never been reached, due to depressed business conditions and latterly to the world copper agreement limiting production. It may be said, however, that the present installation has proved its ability to produce in excess of its rated capacity, and with relatively minor additions to plant and equipment that capacity can be doubled. Owing to the severity of the winters, when temperatures of from 20 to 40 degrees below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were rather unusual in copper-refinery construction.

Jan 1, 1932

By A. P. Yovanovic, P. Bonadia, M. N. Moraes, C. F. Matos

"The magnesite flotation operation of Magnesita Refractories, in Brumado – Brazil, has four parallel ball mills working in closed circuit with hydrocyclones to grind the ore for the reverse flotation of silicates in mechanical cells. The modification proposed here opens the circuit for three of the ball mills so that their products are collected together to feed a high frequency screen. The oversize of the screen feeds the fourth ball mill in closed circuit for secondary comminution. The product reports to dewatering and flotation. The undersize undergoes desliming and subsequent flotation operation. According to pilot tests performed, the modification on the magnesite flotation operation will promote a 20% increase in the productivity, 8.5% increase in mass recovery and a 26% reduction in water consumption. The gains are due to the fact that the silicates in the feed are concentrated in the smaller particles (<100µm) with over grinding in the existing closed comminution circuit, making it impossible to take advantage of this natural selectivity. The combination of open circuit, more selective milling, and the high frequency screen, ensures high efficiency particle size classification. This renders the process more effective, both to the screen undersize with its high contents of silicates and fines, and to the screen oversize, which is almost without fines and has a higher magnesite grade. This situation allows for the setting of specific parameters for the flotation of both the primary milling undersize and the secondary milling product.INTRODUCTIONMagnesita Refractories, with its operations site in Brumado, is the largest producer of high purity dead burned magnesia (DBM) in Latin America. The magnesite ore is extracted from an open pit mine, named Pomba, after which it is crushed and handpicked. Due to the presence of disseminated silicate the ore has to be ground and concentrated by means of reverse flotation, before feeding the high temperature kilns for sintering and conversion to DBM.The magnesite flotation unit has an impact crusher to reduce the size of the feeding ore, which is transported to the mills by conveyor belts. The milling operation is composed of four ball mills in closed circuit with hydrocyclones. The closed circuit generates a high circulating load with excess fines, which is detrimental to the selectivity of the desliming and flotation operations, reducing both mass andmetallurgical recovery.In the current scenario, the capacity of the flotation plant is insufficient to meet the demand of the DBM kilns, forcing the operation to work with high purity ores in order to attain the highest possible mass recovery in the concentration process. This is not an ideal situation as it requires the mining site to work with higher stripping ratios.The objective of this work was to improve the magnesite flotation unity to increase its productivity. After a detailed analysis, the milling was identified as the limiting process, which made the authors to focus on this operation."

Jan 1, 2016

By J. G. Kelly

"IntroductionOver the past twenty-five years of improvements to scooptrams In the Ontario Division of Inco Ltd., records indicate that on average, an 8 yard capacity machine at 80% availability will load, haul and dump about 100TPH from an average stoping area. This, essentially, means that Inco mines are limited to 2000 TPD as an approximate maximum production cap per minute. Some of the improvements made to scooptrams over this period have been:• dry disc and oil immersed brakes on larger loaders;• to replace air over hydraulic systems;• modulated shift transmissions;• greater breakout and tramming capacities by using larger engines and buckets;• operators&apos; compartments have been enlarged and better seats,• joystick controls and air-conditioned cabs have been utilized&apos;• major cost savings have been realized through tire maintenance improvements; and• major savings, safety improvements and increased ore recovery by using remote controls.After reciting the improvements listed above, and the list is by no means exhaustive, it is quite obvious that scooptrams are a mature product and that major design or performance improvements will not occur in the futre. Any futher improvements will be incremental in nature. Loading, hauling, and dumping with scooptrams is a batch process and as such is limited in its total output.Continuous Load/Crush/Convey Systems:In order to improve productivity, a radical new system was required. The target was 2000 tons per shift. In 1984, to meet the goal, Inco acquired the rights to a contiunous loader from Canadian Mine Services. Inco made modifications to the original prototype machine, such as: (I) conversion from rail mounted to crawlers for increased mobility; (2) a hydraulic cooling system was added; (3) flight bars were changed from cast to forged; (4) motor horsepower increased to 200 hp from 150 hp. Emerging from these modifications came a machine known as the CL-looo Oscilloader (Fig. 1).The CL-looo Oscilloader is an electric hydraulic 35-ton machine which is crawler mounted and has a drawbar pull of 30 tons. It has an adjustable frequency, oscillating lip which simulates the digging action of a manual .shovel. This action agitates and lifts the muckpile enough to allow it to settle by gravity onto the chain and flight conveyor table which then removes the ore to the tail end for discharge into either a crusher, a conveyor, a truck, or a combination of these.Late in 1985, six oscilloaders were fabricated and put into Inco mines for field trials. At Creighton Mine some early field trials were conducted with a rail mounted continuous loader loading directly into 140 cu.ft. Granby cars. Much of the field testing was in VRM drawpoints with the Oscilloader loading into 20-ton trucks or into Teletrams . At Levack Mine, by puttmg the truck on remote control, it was possible to have the operator run the Oscilloader and load his own truck (Fig. 2). At McCreedy West Mine, Copper Cliff North Mine, and Copper Cliff South Mine, the Oscilloaders discharged directly into 26-ton trucks."

Jan 1, 1988

By E. Dernedde

Cell rooms of aluminium smelters have large openings in the sidewalls and in the roof. These openings provide a high ventilation rate, which removes heat and contaminants emitted by the reduction cells and thereby ensures acceptable working conditions inside the cell room. However the large openings make the airflows through the smelter building sensitive to the wind. In this study equations for the airflow through the openings of a smelter building exposed to crosswinds were developed and verified against plant measurements. The equations were then used to estimate the airflows through a two-storeyed smelter building containing VS Soderberg cells. Wind protection by wind-covers over the sidewall openings and by upwind buildings made the airflows through the building less sensitive to the wind. Physical and mathematical modelling showed that working conditions inside the wind-protected cell room would be acceptable for crosswinds at speeds up to 16 km/h. These predictions were confirmed by measurements taken in a VS Soderberg smelter.

Jan 1, 2007

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By Ahmad Ghahremaninezhad, Rebecca Radzinski

Arsenic is a highly toxic compound that is naturally found in the environment and is released through the processing of sulphide minerals. Arsenate (As5+) is less toxic than arsenite (As3+) and is soluble in water but can form insoluble precipitates when metal ions are present. The arsenic removal processes used in industry assume that arsenic is in its pentavalent state. Hydrogen peroxide can be employed to oxidize arsenite; however, it is expensive. It has been shown that activated carbon can be used to catalyze the oxidation of arsenite with oxygen as the only consumed reagent at ambient conditions with an efficiency of 99% in less than 24 hours. The mechanism which oxidizes arsenite is not yet understood; however, this study shows that a strong oxidizing agent is formed in-situ. The species and amount of oxidant formed were determined via iodimetric titration and electrochemical methods. The production of oxidant was optimized by comparing the amount of oxidant formed in-situ to the relative amount of arsenite oxidized.

Jan 1, 2015

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By Elaine R. Goetz

The eastern and southeastern regions of Ohio are part of Appalachian coal country, with a documented 1,300 miles of streams impacted by acid mine drainage. Since 1995, partnerships of local watershed groups, government agencies, private industries and universities have focused on the remediation of the affected waterways. The partnerships have spent $2.4 million annually in constructing and operating treatment systems such as wetlands, anoxic limestone drains, successive alkalinity production systems, steel slag leach beds, and lime dosers. These systems have been partially successful, and water quality has improved in the region, but no treatment has yet met the ultimate objectives of low cost, continual remediation. Our research group has investigated an alternative system for acid mine drainage treatment: electrolysis combined with pH adjustment to selectively precipitate recoverable, saleable metal products to offset the cost of treatment. We utilized a $0.2 million pilot facility constructed by the Wayne National Forest, in Nelsonville, Ohio, to process approximately 40 L/min of mine drainage from surrounding seeps. The pilot facility has multipurpose tanks that can be adapted to process acid mine drainage with different characteristics, such as high or low aluminum content or high or low carbonate concentrations. Sodium hydroxide was used for pH adjustment. Results indicate that saleable product can be generated with this treatment technology. In an initial, not optimized trial, one seep yielded 4.7 kg of dried 69 % iron oxide product from 10 hours of pilot facility operation, treating 23,000 L with electricity costs of $4.68. Dissolved iron concentrations in the water were reduced from 242 ± 18 mg/L to 2.8 ± 2.0 mg/L (99.0 % removal) while the initial acidity of 443 mg/L as CaCO3 was neutralized to an alkalinity of 160 mg/L as CaCO3. Iron oxide can be sold as pigment for an average of $1.47 per kg in the United States. Currently, approximately 80 % of all pigment used in the United States is imported, and there is incentive to purchase domestically recovered pigment. If the iron oxide from the pilot facility could be sold as pigment for $1.47 per kg, 43 % of the operating cost (raw materials, electricity and construction costs) of treatment could be offset by the sale of the product. Considering the cost offset, the electrolysis process shows potential as a sustainable low cost alternative for treating acid mine drainage.

Aug 1, 2013

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By R. F. Favreau, L. C. Lang

"In modern blasting technology blasts are designed and analysed on an energy-mass-time relationship. The energy of the explosive is derived by computer analysis and the work potential of the available energy is expressed in numerical values. The mass involved in the blast is determined by the geometry of the blast and by the rock density. Time is also a relevant parameter, because time is required to complete the three basic stages of the breakage process.For successful application of the blasting parameters the basic mechanism of the breakage process must be understood.The physical-mechanical properties of the rock, local structural geology and the thermodynamic properties of the explosives can be brought together to create a computer model of a blast with which it is possible to predict separately the results of each parameter and to express the predicted degree of change in any parameter by actual numbers.A long-range project has started to create a ""bank"" of rock properties for as many Canadian and foreign mines as possible. A computer model has been successfully applied to predicting the effect of varying the ratio of spacing to burden at constant rock volume and significantly improved results are achieved, as the S/B ratio is increased up to about 2 to 2.5.High-speed photography has been applied to determine the time that has elapsed between zero time and the beginning of movement of the mass. The results assist in determining minimum and optimum delay time required for multiple-row blasting.The approach as described in the paper is now well proven and is clearly superior to previous methods based on powder factors and human assessment."

Jan 1, 1972