Search Documents

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By J. P. Mogan, E. D. Dainty, K. Katsuyama

"The Volvo BM 861 U articulated truck is one of the few underground diesel units manufactured by an organization which shares the same corporate roof as the engine manufacturer. As a consequence, the unit has provided an opportunity for the characteristics of the entire system- turbocharged aftercooled engine, transmission and exhaust scrubber- to interact to minimize emission levels. The performance of the components of the system, as evaluated by full-scale dynamometer testing, is summarized. The over-all effect of the various innovations was a 38% reduction in the recommended ventilation level over that of the bare engine.IntroductionThe Mining Research Laboratories of Energy, Mines and Resources Canada is required, as part o f the certification service of the Canadian Explosive Atmosphere s Laboratory, to test the exhaust emissions of diesel engines, and to recommend appropriate amounts of fresh ventilating air to minimize the risks to health of underground personnel working with, or in the vicinity of, such diesel engines. Volvo BM AB of Sweden made application for the certification of the BM 861 U truck during a period in which EMR personnel were engaged in a number of research projects concerned with improving the environment in dieselized mines. One such avenue of research was the venturi or high-energy scrubber; as the BM 861 U was equipped with this type of scrubber , EMR and Volvo BM agreed to cooperate in a considerably more extensive investigation than would be normal for a certification application. The outcome of some of this research is summarized in this paper."

Jan 1, 1981

By Marc C. Bétournay

A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development of the world?s first fuelcell production vehicle, a mine locomotive. A mine loader project has also started and several other projects are planned. These projects are providing the mining industry with the required information to make this technology shift possible. The application of fuelcell power will yield several important benefits such as the elimination of underground diesel emissions, significant reduction in the primary extraction?s sector greenhouse gas emissions and support for a more productive scenario. This article reviews these successes, discusses ongoing and potential projects and presents the technology application benefits that could be possible for mining operations.

May 1, 2003

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By D. Stüben, G. P. Glasby

"Abstract - Shallow submarine hydrothermal fluids from Paleohori Bay off the Greek Island of Milos have been investigated in detail. The extensive gas and warm (max. 93°C) water vents are enriched in major components such as C1-, Na+, Si, Ca2+, Mn, PO4 3-, NH4 +, K+, Sr2+, H2S and CH4 and depleted in Mg2+, O2 and SO4 2- relative to ambient seawater. Based on zero-Mg calculations, it is deduced that the submarine vent fluids are related to the geothermal reservoir beneath Milos which has a similar chemical composition. Fluid samples from each vent in Paleohori Bay represent a mixture of hydrothermal end-member fluids derived from the upper and deeper geothermal reservoir systems of Milos, a mantle-derived source, a high-chloride fluid resulting from phase separation of geo thermal fluids and a steam-heated CO2-rich meteoric water. Résumé - À l’île de Milos dans la mer d’Égée, des fluides sous-marins hydrothermaux en eau profonde ont été récherchés en détail près de la baie de Paleohori. Les larges émanations de gaz et d’eau chaude (temperature maximale: 93°C) sont enrichies en constituants principaux tels que de Cl-, Na+, Si, Ca2+, Mn, PO4 3-, NH4+, K+, Si, Sr2+, H2S et CH4 et appauvries en Mg2+, O2, SO4 2- comparé à l’eau de mer environnante. Selon le calcul du zéro-Mg, nous en déduisons que les fluides sous-marins hydrothermaux sont dérivés du réservoir géothermal sous l’île de Milos car leur composition chimique est la même. Les prélèvements des fluides de chaque source hydrothermale représentent un mélange de fluides hydrothermaux dérivés des réservoirs géothermaux supérieur et inférieur, d’une source dérivée du manteau, d’un fluide très enrichi en chlorure produit par la séparation des phases et de l’eau météorique enrichie en CO2 et chauffée par la vapeur."

Jan 1, 1999

By G. Chi

Outline 1.Regional geologic setting 2.Host rocks and structures 3.Mineralization, alteration and paragenesis 4.Geochronology 5.Major and trace elements 6.Fluid inclusions 7.Carbon and oxygen isotopes 8.Conclusions

Apr 1, 2005

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

By C. J. Newman, D. J. Kemp, R. M. Sweetin

"The smelter is described by area; feed preparation, continuous furnace line, gas handling and auxiliary systems, blister refining, Hazelett casting of thin anodes, and scrap remelting. Early smelter campaign data is presented and compared to design. Some modifications to the basic design of the furnaces and gas trains are indicated, with their respective impacts on improving smelter performance.Plant compactness, the use of jumbo tanks, and a highly automated electrode handling system are featured in the refinery description, with brief coverage of the liberator and slimes leaching sections. Early experience in refining thin regular Hazelett anodes, and submersible pump recovery of raw slimes are relayed, together with automatic stripping from titanium blanks.Refinery tonnages and operating parameters are given showing the relatively trouble-free attainment of refinery design performance.IntroductionPrevious papers and articles ( 1), (2) ,(3 ) have described the metallurgical facilities serving the copper-zinc-silver Kidd Creek orebody located near Timmins, Ontario. For convenience a brief review of their mid-1983 operating status is presented.The concentrator, originally designed for 9,000 short tons, was commissioned in late 1966. It can now comfortably process over 13,000 metric tonnes per day largely as a result of the addition of a fourth circuit in 1978."

Jan 1, 1984

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By Vicki Tschirhart, Bill Morris, McMaster University

A new method for mapping faults within basement rocks underlying the Thelon Formation and glacial overburden was developed and tested in the Aberdeen Sub-basin. This method utilizes newly acquired aeromagnetic data, the Blakely algorithm for defining magnetic source edges, a calculated dip-direction map, a digital elevation model (DEM) derived from the Canadian Digital Elevation Database, and the positions of identified, inferred and newly mapped faults that are within and adjacent to this sub-basin. Combining these data revealed three age groups of faults. One group is seen only on the DEM; these faults are young brittle structures that have no effect on the sub-Thelon basement unconformity, and are not visible on the dip direction map. A second group is evident on the dip direction map but not the DEM; these faults are old basement structures that did not propagate upward through the Thelon Formation. The third group is expressed on both the DEM and dip direction map; these faults are also old structures that propagated upward during and/or after deposition of the Thelon Formation. The latter group of faults may be of greatest interest for uranium exploration, with reactivation increasing their potential to serve as conduits to transport uranium-rich fluids and focus deposition at or near the unconformity surface. This methodology has promise for comprehensive mapping of basin faults and tracking the tectonic development of the whole Thelon Basin through time.

Jan 1, 2013

By Andre du Preez

Emergency Fall Arrest System Rio Tinto?s Primary Objective: ?To achieve repeatable controlled safe deceleration rates during emergency fall arrest activation (Ontario OHSA Regulations) ?Must operate effectively on mine specified steel shaft guides.

May 1, 2013

By G. Lucas

"Material substitution occurs continuously in response to competitive and economic pressures. Technical development can accelerate or slow substitution by improving the performance of the invading or defending material. The choices are seldom simple and have to be made in the context of continuous commercial change.The development and commercialization of a new aluminum material is examined. The material has been introduced into· several different markets, so it is possible to compare and contrast the degree of success obtained in each.IntroductionAluminum-based materials have been in use for over one hundred years and , therefore, the development of a new family of alloys is rare. In the early 1970s, Dr. L.R. Morris and his coworkers at Alcan' s Kingston Research Centre started work on what was, at the time, something of a scientific curiosity-a family of alloys strengthened by an unusual mechanism.This paper deals with the development and commercialization of what became known as the Alcan 255 alloys"". These alloys have found uses in several markets, usually as improved substitutes for existing materials. Forecasting the usefulness of a substitute material in an existing marketplace is difficult, in part, because even material users are seldom able to specify precisely their requirements. This uncertainty can cause the failure of some substitutions but can also lead to opportunities which were not initially obvious.Technical BackgroundPure aluminum is a soft, weak material. It can be strengthened by the addition of various alloying elements and by work hardening. Alloying elements usually act by forming solid solutions which are stronger than the pure metal or by precipitating during heat treating or aging and so preventing the easy movement of dislocations during deformation. Elements which can perform either role had been investigated for decades and were thought to offer little chance of technical breakthrough in 1970. An outgrowth of the then new and exciting research on directional solidification seemed, however, to offer such promise.Some aluminum-iran-manganese alloys will solidify under certain conditions as 'coupled growth' eutectics (Figs. I and 2). The microstructure shows one phase growing as long rods through the other. This is an uncommon structure and it was investigated to see if it had equally unusual properties. On deformation by rolling the rods were broken up into small equiaxed , evenly-spaced particles (Fig. 3). Materials with this structure were found to be stronger than other alloys with similar amounts of alloying addition, and to resist thermal softening remarkably well. This combination of properties was thought initially to be due directly to the particles by a dispersion strengthening mechanism, but later this was found not to be strictly true."

Jan 1, 1987

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine's in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew's analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949