Search Documents

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

By G R Ryan

Dissatisfied with conventional wet processing methods for alluvial deposits, Resource Trend Pty Ltd of Cairns set out to develop a better process. After comprehensive investigation of existing dry techniques the principals have now developed a rotary dry concentrator that can handle the fine-grained fraction of alluvial deposits as well as the coarse. Four of these units have been mounted on an integrated towable treatment plant which has been in successful commercial operation for four years in northern Queensland. A second plant is now under construction for use in the United States. Grades of less than 0.2 g/lcm have been profitably mined at throughputs of about 80 cubic metres per hour and 85 per cent availability. The operation runs round the clock with an establishment of four. Major benefits, apart from lower capital and operating costs, are environmental. Ore is picked up, treated, and replaced in its original mixed condition within 25 m of its initial location. Rehabilitation is completed almost immediately behind the plant as it advances, leaving no slimes dams, coarse stockpiles, or haul roads. In 1993 the company won a Premier's Award for Environmental Excellence in the Queensland Mining Industry. The principal disadvantage is moisture, and the company is now actively seeking deposits in the deserts of the world. In Queensland mining is normally possible only for six months of the year.

Jan 1, 1994

The Tavua Power Proprietary Ltd. was created in 1936 for the purpose of supplying electric power, compressed air and water to the mining field.The original share capital was subscribed on a two-third:one-third basis by the Emperor Gold Mining Company Ltd. and Loloma (Fiji) Gold Mines, N.L. In 1940, Fiji Mines Development Ltd. (later changed to Dolphin Mines Ltd.) was admitted as a shareholder, and, in 1950, a further change occurred. The present shareholding in the Company is as follows:A central power station was decided upon to reticulate power and compressed air over the whole field and building commenced in May 1936.The original plant comprised three Belliss and Morcom diesel generating sets 770 b.h.p. 525 kW 3,300 V, 3 phase, 50 cycle; one Belliss and Morcom diesel compressor set 2,09'0 cu. ft. of free air per min. at 90 lb. gauge 300 r.p.m., and two small Ruston-Holman diesel compressor sets each of 525 cu. ft. capacity taken over from Loloma (Fiji) Gold Mines, N.L., and the then existing Koroere Gold Mining Company.BuildingThe original building was 130 ft. long by 47 ft. wide with an elevated switchgear annex on the west side from which a clear view of the engine room is available.

Jan 1, 1953

By Voorhees JS, Bureau G

To operate a mine in California requires compliance with State environmental regulations, including assessment of risks and associated financial assurances for postulated worst case catastrophic event scenarios. Carson Hill Gold Mine, an open pit, heap leach operation, completed new risk assessment catastrophic event analyses in 1988. The risk assessment was performed at the same time that a new leach site (Leach Site 3) was being designed. Leach Site 3 is located about 400 m upslope of New Melones Reservoir, which is a public recreation facility and a source of drinking water. Release of leachate (pregnant solution) or ore containing cyanide and metals from Leach Site 3 into New Melones Reservoir was considered to pose the largest risk of environmental damage.Flow failure of the ore heap, potentially induced as a result of liquefaction of the saturated portion of the ore, and/or overtopping of the leach site containment embankment due to excessive precipitation were found to be the most plausible leachate release scenarios. Yearly combined probabilities of various downstream release volumes were estimated. The release volume corresponding to a yearly probability of 0.05 percent was then used to estimate potential environmental impacts and mitigation costs. The costs include earthwork to restore the geometry of the ore heap and repair the fill slope below the Leach Site 3 containment, and impacts on New Melones Reservoir.

Jan 1, 1990

By Mann LD

The Haveluck gold deposit, located 2.5km north of Meekatharra, contained 1,284,000 tonnes at an average grade of 1.8 g/t gold of drill delineated proved and probable ore prior to commencement of production. Following successful laboratory and pilot scale testing a decision was made to establish a 300,000 tonnes per year heap leaching operation. The ore, crushed to minus 100mm was stacked on an impermeable membrane and irrigated with a dilute cyanide solution. Gold was recovered from the resulting pregnant solutions by adsorption onto activated carbon and gold bullion produced in a modified Zadra process desorption plant. From the commencement of mining it was obvious that a high percentage of fine material was being produced which would adversely affect the percolation of the cyanide solution-through the leach heaps. A screening plant was incorporated into the crushing circuit which provided an oversize product satisfactory for heap leaching and an undersize for carbon-in-pulp treatment. Plant design provided for the slurrying of minus 0.8mm ore before feeding to the pachuca tanks. Initial practice was to use four tanks for gold dissolution and two for carbon contact. Vibrating screens were used through- out for the carbon-ore separation and the loaded carbon was stripped in the existing desorption plant.

Jan 1, 1982

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

By Eldridge B. J

During recent years, Central Queensland has experienced a boom in its coal mining industry. This has involved many companies in projects requiring large capital expenditure. As with most projects of this size, many operating problems are now being experienced which were unforseen at the feasibility stage. One of these problems is the failure of pit slopes and spoil piles at some of the strip mining operations. There have been serious stability problems associated with Utah Development Company's strip mining operations in Central Queensland, in particular the Goonyella Mine. A field investigation programme was under- taken to determine the cause of highwall and spoilpile slope failures. Spoilpile failures were found to result from weakness near the spoil/floor contact zone. Highwall failures were found to result from a combination of unfavourable bedding plane dips and weakness, and the presence of joints in weak o~erburdep; Satisfactory solutions fa the staiity, problems are difficult to formulate, and-field stability experimentation is still at an early Stage.

Jan 1, 1974

Instantaneous outbursts have occurred at Metropolitan Colliery from the pick and shovel work of early days to the modern mining techniques of today. Developments have been the introduction of an emission index to measure the proneness of the coal to outbursts, drainage and destressing by large diameter holes, attempts at higher productivity by the introduction of pulsed infusion shotfiring and improvements in ventilation. The future plans and aims for the Colliery include prediction of outbursts, seam gas pre- drainage and longwall mining.

Jan 1, 1980

By Tapp B. A

To date, few studies have been made regarding the energy requirements of the Australian mining and mineral processing industries. This paper indicates that these industries use a substantial proportion of the total Australian energy input (32.7% in 1971-72 and 36.10% in 1974-75). With the growth orientation of these industries, this input is likely to increase. Data shows that mining energy requirementE varied from 4.22% (of total Australian energy requirements) in 1971-72 to 4.16% in 1974-75. Energy requirements for the total mineral processing industries increased from 28.49% to 31.93% for the same period. The total estimated primary energy input varied from 22.56% to 25.2%, whilst indirect energy use, in the form of electricity increased from 10.16% to 10.66%; in the same period. Analysis of primary energy input data within the processing industries (1973/4) showed that the Iron and Steel Industry consumed 15.03% of the Australian total consumption, Non-Ferrous metals, 5.43%, Cement, 1.64%, and Refractories, 1.59%. In toto this represented 24.57% of the total

Jan 1, 1979

The lignite mines in the Latrobe Valley of Victoria/Australia have been using continuously operating mining systems for more than 50 years. The relatively small bucket chain dredgers of the early years have been progressively displaced by bucket wheel dredgers with increasing size, increasing capacity and increasing service weight. The large machines for the new open pit Loy Yang have a bucket wheel outreach of 46m, an effective capacity of 3350 bm' coal/h respective 2500 bm' overburden/h and a serv- ice weight of approx. 4500 t. The time between signing of con- tract and starting of operation for these machines is at least four years. The high service weight, the resulting high capital invest- ment and the long period for design, design review, manufac- turing, erection and commissioning of these machines directed the SECV to investigate a possible application of compact dredgers for the Latrobe Valley.

Jan 1, 1989

Economic and technical reasons forced the mining industry all over the world to increase the unit size of mineral processing equipment. in large flotation cells, this development leads to problems in areas of air dispersion and keeping solids in suspension. Outokumpu, an operating mining company, designed and developed a mixing mechanism for large flotation cells at its own concentrators and also studied problems related to tank design. Ideal conditions for flotation can only be achieved if the flow pattern created by the mixing mechanism fits well into the tank configuration and the risk of short circuiting is minimized. In large deep flotation cells, four different zones can be found which improve the behaviour of large cells when compared to small cells. Selectivity is increased and in some cases final concentrate grades can be produced from the rougher cell. The largest units have also been used as final cleaners in some installations. When modernizing old plants by installing fewer larger flotation cells, immediate and substantial savings in power consumption are achieved. Additional power savings are made in pumping costs because of simpler circuit design and decreased circulating loads

Jan 1, 1978

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

It was once considered sufficient to revegetate old mine sites using grass or trees. At the commencement of the Stawell JV (SJV) operation in 1981, management determined that pre-existing vegetation would be replaced. This policy was somewhat 'ahead of its time'. The cost of rehabilitation at SJV averages $8000 per hectare. Rehabilitation of this calibre requires a practical understanding of local ecosystems.

Jan 1, 1992

In 1972, with the West Lyell Open Pit winding down, mining operations transferred underground. All development tunnelling until the end of the decade was carried out by a fleet of ten pneumatic Jumbos.A decision was made in 1980 to purchase an electric-hydraulic Jumbo and a second was purchased in 1982. Their introduction changed the face of development at Mount Lyell. Significant new demands were placed on main-tenance sections, particularly on electrical reticulation.Subsequently, two further electric-hydraulic Jumbos were purchased from Agnew Mining in 1984, and successfully overhauled and commissioned. As well, two electric-nydraulic production drilling rigs have been purchased. Only one of the original pneumatic Jumbos remains in service.

Jan 1, 1985

By B Green

With a focus on safe productive tonnes, there has been an ongoing drive to increase the productivity of the mining fleet across BHP Billiton. In response, a team from the Iron Ore business was formed to review all aspects of the end-to-end drill and blast process and to challenge conventional practices that limit production efficiency. As a result of the outcomes of this work, a number of initiatives were identified to improve operational practices that have also delivered significant cost savings.One such initiative was to increase pattern size to a minimum of 1 Mt where practicable, thereby creating ‘megablast’ as a new standard across all mines. To achieve blasts of this size, the team had to overcome the complex problem of integrating wall control into the megablasts.With traditional blasting techniques, the key strategy, which is also historically inefficient but was thought to be integral to having stable, safe walls, was to utilise the trim blasting/modified production blasts technique (ie narrow blasts along the pit wall designed to ‘peel off’ the material while minimising the effects of vibration and charge confinement on wall integrity).Small traditional trim patterns comprise three to four rows of production holes and one or two rows of batter/buffer holes of reduced diameter that require the firing face to be completely exposed before blasting. This is an extremely slow process that requires a lot of resources for very little tonnage while adding additional expense to the final cost per tonne.This paper will show how the megablast approach was developed to control damaging vibration and confinement effects, flyrock and fragmentation while having the largest possible blast that includes wall control. The new practice is based on a theory that involves the initiation point and control row being the second row of holes from the pit wall itself. Adjusted charges in vented batter and buffer holes help to achieve an optimal toe design, and at the same time create a zone of broken ground that absorbs damaging vibrations formed by the attached production blast of any size, whether it is a straight wall or a multi-angled complex pit shell design.Using the new style of blasting has allowed an increase in the size of the patterns from an average of 300 kt to over 1 Mt whilst maintaining pit wall integrity. Case studies will be presented showing drill, charge and tie-in designs with the presentation having additional blast videos, including overall shots of blasts and in-close footage of what happens behind the blast at the crest of the planned catchment berm.The paper will also demonstrate the flow-on effect of using this style of blasting to reduce operational costs associated with other downstream processes, such as the reduced requirements for pattern preparation, an increase in productive digging, reduced maintenance costs and a decrease in fuel burn for equipment.CITATION:Green, B, 2015. Megablasts – enabling technologies in BHP Billiton Iron Ore, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 599–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

In November, 1967, a four strand curved mould continuous casting machine coupled with a 50 ton basic oxygen furnace began producing billets for the rod mill and new merchant mill at the Newcastle Steelworks. To date over 500,000 tons of carbon and alloy steels have been cast at the rate of 20,000 tons per month, the major part for the wire industry. Many alterations have been made to the plant to simplify the process, improve quality and increase production. Casting parameters have been developed for each different type of steel. The quality of the final product has been influenced most by casting temperature, secondary cooling and casting speed. All these factors have been controlled and good results are reproduced. More exacting requirements of liquid steel quality have brought about the use of higher lime/silica ratio slags during steelmaking to control phosphorus revers- ions and standard ladle additions of manganese suicide and ferro aluminium for more effective deoxidation.

Jan 1, 1972

By L C. Thompson

Biomineralisation is the process by which microorganisms mediate and catalyse inorganic reactions so as to form new mineral assemblages. The goal of biomineralisation as a remediation tool is to control microbial processes and their environment so as to sequester and immobilise specific toxic metals within exceptionally strong bonds of neo-formed mineral assemblages. In this way, the bound metals are no longer mobile within a geological time-scale. Applied biomineralisation uses microorganisms, which are isolated from a metal waste environment and are selected for their ability to rapidly catalyse neo-mineral development from dissolved or leachable metals. A typical waste environment will contain microbes that contribute to the mobilisation of metal contaminants as well as microbes that possess the potential for remineralising available metals. Selection and augmenting the correct combination of bacteria and eliminating the competing mineral degrading reactions are the key to applying biomineralisation as an in situ remediation process. Applied biomineralisation harnesses the microbesÆ ability to stabilise toxic soluble metals into non-mobile mineralassemblages. This paper will discuss and demonstrate the biomineralisation process through several case studies including the Summitville mine site in Colorado, the McCoy-Cove mine in Nevada, the Argonaut mine in California, and an historic lead site in Crooksville, Ohio.

Jan 1, 2004

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

By J F. C L Costa, J C. Koppe

The goal of this study is to characterise co-processed clinkers by identifying the most common minor elements, their distribution in the clinkers and possible effects on the mineralogical properties of the same. The results show the presence of an elevated content of transition metals, especially manganese concentrated in the matrix (up to three per cent) of the clinkers. Anomalous concentrations of arsenic have also been detected, especially at silicate crystal edges. The results indicate that the tracer elements can perfectly be associated to the mineralogical characteristics of the clinkers.

Jan 1, 2008

By S Miller, R Smart, J Thomas

Single-addition and sequential net acid generation (NAG) experiments were carried out on natural and prepared samples with varying contents of organic matter and pyritic S. Results show that carbonaceous matter can produce significant quantities of organic acids during peroxide oxidation in the NAG test, which leads to overestimation of acid-forming capacity and misclassification of benign samples as potentially acid forming (PAF). Organic matter effects were most pronounced in samples with low S (less than 0.5 per cent) and total organic carbon (TOC) contents of greater than seven per cent. The single-addition NAG test will tend to overestimate acid potential in samples with little or no pyrite and high organic matter content, potentially leading to sample misclassification. High pyritic sulfur samples tend to show little difference in single-addition NAG acidities with increasing organic matter, and it appears that pyrite is preferentially oxidised by peroxide when present in significant concentrations (greater than one per cent pyritic S). In sequential NAG tests overestimation was greatest in samples with little or no pyrite, but highly carbonaceous (>20 per cent TOC) pyritic samples were affected in later stages as the pyrite was depleted. A modified NAG method is proposed to account for the relative proportions of pyrite derived acidity and organic acidity in a given NAG solution.

Jan 1, 2003