Search Documents

By C. A. Heberlein

C. A. HEBERLEIN,* New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabarpyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [AMERICAN CYANAMID TEST FEED PER CENT Si02 66.54 A12032.08 CaO0.70 MgO 0.00 Alkalis1.78 Fe15.63 Cu0.44 S9.42 Hg0.45 OZ. PER TON Ag0.95 Au0.151 Screen Analysis of Tailings, Per Cent Plus650.0 Plus 1001.32 Plus 15020.75 Plus 20019.85 Minus 20058.08] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. Of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 1 [ ]

Jan 1, 1941

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

Upon the recommendation of its Technical Committee, The Com-pressed Air Society has adopted the following definitions of, certain terms. Displacement.-The displacement of an air compressor is the volume displaced by the net area of the compressor piston. Capacity.-The capacity should be expressed in cubic feet per minute, and is the actual amount of air compressed and delivered, expressed in terms of free air at intake temperature and at the pressure of dry air at the suction. Volumetric Efficiency.-Volumetric efficiency is the ratio of the capacity to the displacement of the compressor, all as defined above. Compression Efficiency.-Compression efficiency is the ratio of the work required to compress isothermally all the air delivered by an air compressor to the work actually clone within the compressor cylinder, as shown by indicator cards, and may he expressed is the product of the volumetric efficiency (the intake pressure and the hyperbolic logarithm of the ratio of compression), all divided by the indicated mean effective pressure within the air cylinder or cylinders.

Jan 8, 1918

By George H. Hanna

THE importance of the Donets coal field (the Donbas) to the national economy of the Soviet Union is well known. Great as was the significance of this tremendous deposit of coal in prewar days it is destined to become an even greater factor in the economic life of the country now that the tremendous havoc wrought by the Germans is being remedied. Since the war began, new coal fields have been extended; for example output of the Moscow and Karaganda (Kazakhstan) fields has become considerably larger while new mines are producing coal in several parts of Uzbekistan and Kirghizia. The huge West Siberian coal field, the Kuznetsk Basin, is producing more coal than ever before to supply the industries of that region and of the Urals. But so great has been the development of industry to meet war needs, especially in those districts of the Soviet Union that lie to the East of the Urals, that the coal obtained, eked out by such locally-won fuels as peat and wood, is still barely sufficient to meet industrial requirements. The main burden of the coal supply for the restored industries of the West, therefore, will fall on the Donbas.

Jan 1, 1945

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By James W. Halley

"Fine-grained" steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was he grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Houghg reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652° and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvebent in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement6 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved the low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04 and 0.06 per cent added aluminum. The fact that the coarsening temperature passes through a maximum with increasing aluminum content appears to be well established. The aluminum content that

Jan 1, 1947

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By W. J. West, T. D. Mueller, J. E. Warren

Two methods are used to obtain the relatiorlship between ratio of gas to oil permeability and gas saturation. One method is to calculate a curve from field measurements of reservoir behavior: the other is to measure the relationship on a core .sample in the laboratory. The curves resulting from these TWO methods arc often comparer1 and seldom found to agree. The most important reason for the nonagreement is often overlooked. This reason is that the performance k9/k0 curve is calculated with the assumption of uniform pressure and saturution throughout the reservoir. To show the differerence between performance type kg/k0 curves and laboratory type kg/k0 curves. two performance type kg/k0 curves for two different production rates were calculaled from the production perforrnance of a hypothetical reservoir for which a laboratory type curve was assumed. Production performance of the hypothetical reservoir bras calcu- lated by use of international Business Machine's 701 Computer. The perfortnance type kg/k0 curves differed from the laboratory curve for the hypothetical reservoir. The performance type crrrve for the lowest production rate most nearly coincided with the laboratory curve. INTRODUCTION Predictions of oil reservoir performance are often made with the aid of complex numerical calculations. An important quantity required in these calculations is the ratio of gas permeability to oil permeability (kg/k0 )at a particular gas saturation. Two methods arc used to obtain a relationship between this ratio and gas saturation. The curves resulting from these two methods are called performance kg/k0 curves and laboratory kg/k0 curves. The performance curve is obtained from field measurements of reservoir behavior. Particular kg/k0 values are calculated from the producing gas-oil ratio, the cumulative reservoir withdrawals, the original oil in place, the average reservoir pressure, and the PVT properties of the reservoir fluids. The particular kg/k0 values are then plotted against the average rcservoir gas saturations for the entire history period. In order to use this derived kg/k0 relationship for performance predictions, a curve through these points is extrapolated to higher gas saturations. The laboratory kg/k0 curve is obtained from measurements made on core samples. Saturation is maintained uniform throughout the core during these measurements. The kg/k0 curves obtained with these two independent methods are often compared and seldom are found to be the same. Various reasons have been offered for the lack of correlation. One is that insufficient core? were obtained to derive a curve representative of the reservoir rock. Another is that laboratory methods have failed to reproduce reservoir conditions. The most important reason for the noncorrelation has been often overlooked because of the difficulty in evaluating its effect. This reason is that the performance or field kg/k0 curve is calculated with the assumption of uniform pressure and saturation throughout the reservoir. In any

Jan 1, 1956

By WALTER S.

(New York Meeting, February, 1912,) THE earliest example of attempting to form finely-divided materials into larger masses for better adaptation to commercial use was probably the briquetting of peat and lignite-waste at Paris by the use of a clay binder. It was from this attempt that our word briquette has arisen (Fr. la brique), the formed masses being shaped similar to ordinary bricks. This term does not, however, lend itself to the many shapes of such formed material as are now being produced, as few of them aside from some of the European brown-coal products bear any resemblance to the shape of that well-known article. The term "agglomeration " has therefore been chosen as more accurately descriptive of the products now being manufactured, this term including the molding as well as the sintering. With the increasing prices of fuel and ores and the greater demand for economy in the operation of industrial plants, more ,attention has been paid in recent years to the utilization of waste products and low-grade ores and fuels. Much of the waste has been occasioned by the inability to utilize finely ,divided ores and fuels in the furnaces because they could not be kept there, or else because they clogged up the furnace-shaft so that gases could not be forced through under ordinary conditions of operation. As a result, all such fines were thrown on the dump. Again, with the exhaustion of the richer deposits of ores, concentration of lower-grade ores becomes a necessity, and most concentrates are produced in a finely-divided condition. Aside from these considerations, there is also the economy in the cost of operating the plant; a furnace running on agglomerated material will have a much greater output than one working on fines. In one instance the charge of an iron blast-furnace was changed from fine concentrates to briquettes and the output was increased four-fold; better results could have been obtained had facilities been at hand for taking care of the increased output.

May 1, 1912

By Perry Harrison

THE increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and, economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd 'continuously operated sinter-machine installations located anywhere. PER CRUDE TON Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? PER SINTER TON Royalty on Ore 0.10 Royalty on Flue Dust 0.15 PER CRUDE TON "Winter expense"; i. z., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for. any ore, viz:

Jan 1, 1932

By Atmaram H. Soni

A statistical study of machinability led the writer to examine existing data in regard to a thermal conductivity-mechanical properties relationship. Various functional relationships were proposed and the multiple correlation determined by statistical methods discussed in detail in the 1iterature.4 The relationship having the greatest engineering and statistical significance is discussed below. The data for cast and wrought aluminum alloys''2 have been compiled and analyzed separately. The results of these analyses are presented in Table I. The empirical equations for estimating the thermal conductivity (cal sec-' cm-I °C) are: for cast aluminum alloys K = 0.584 -0.00984/ -0.00263 Hb [1] and for wrought aluminum alloys K = 0.604 -0.00424l- 0.00170 Hb [2] where 1 and Hb are the percentage elongation and Brinell hardness number. Results of a similar analysis pertaining to stainless steel3 are also given in Table I. This empirical equation for estimating thermal conductivity (Btu per sq ft per hr per °F per in.) is K = 216.19- 1.716l - 0.0997 Hb [3] The relationship between electrical resistivity and mechanical properties was also examined for aluminum alloys using the same statistical method. These results are listed in Table II. While the situation of exact multiple correlation

Jan 1, 1965

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By Gerhard Derge

THE introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be described. For most of the additions, solutions containing 0.001 and 0.01 .moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-bonate as follows: pH 0.1 M NaHCO3 8.4 2 parts 0.1 M NaHCO3, 1 part 0.1 M Na2CO3 9.5 1 part 0.1 M NaHCO3, 2 parts 0.1 M Na2CO3 10.0 0.1 M Na2CO3 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves-sulphate, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only-fluoride, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also-phosphate, perborate, and chromate.

Jan 1, 1939

By James Barr

The process of manufacturing ferrophosphorus lies not alone in smelting a mixture of phosphates, silica, iron ore, with coke as fuel, but upon smelting this mixture with coke and air as chemical agents as well as heat producers and in conjunction with extraordinary procedures and manipulations making the process continuous and profitable. For best results there must be cool top, limited fusion zone, hot bottom, good mechanical condition of stock and perfect distribution of gases; also minimum air supply, high heats and excess of coke or carbon. FERROPHOSPHORUS, an alloy of phosphorus and iron or perhaps a physical mixture of definite compounds of iron and phosphorus, has become of increasing importance as the use of the basic open hearth has extended. Commercial ferrophosphorus is a porous, brittle metal of crystalline structure and often with a bluish metallic luster. A typical analysis is as follows: PER CENT. Phosphorus 18.0 to 22.0 Iron 80.0 76.0 Oxygen 0.2 Sulfur : 0.3 Silicon 0.1 Carbon : 0.1 Manganese 0.2 This alloy was first made in an electric furnace, as it was thought that the high heat of the electric arc together with the reductive effect of carbon was necessary. About 1898, J. J. Gray, Jr., was producing a high-phosphorus pig iron in his furnace at Rockdale, Tenn., by using high-phosphorus, local iron ores. As these high-phosphorus ores were difficult to obtain, he conceived the idea of increasing the phosphorus content of the pig iron by the addition of phosphate rock to the furnace burden. When the phosphorus content of the pig was kept low and only small amounts of phosphate rock were added to the burden, no particular troubles were encountered, but when he increased the amount of phosphate rock to produce an 18 per cent. alloy, his furnace troubles rapidly multiplied.

Jan 10, 1924

By Hsun Hu

NOT much data are available in the literature on textures in cross-rolled metal sheets. Among the body-centered-cubic metals, a few investigators have studied the preferred orientations developed in cross-rolled and in subsequently annealed molybdenum specimens.1-4 Semchyshen and Timmons5 onstructed complete pole figures for the cross-rolled and subsequently annealed arc-cast molybdenum. They used the conventional photographic method. Similar data on cross-rolled iron are still lacking. In view of the fundamental importance of iron as a basic metal for magnetic alloys and many industrial steels, the present investigation was undertaken in an attempt to understand more about its properties. The material selected for the present work was of high purity, and the textures were determined by the Geiger counter spectrometer technique, which permits the construction of quantitative pole figures. Experimental Procedure The material used for this investigation was NRC (National Research Corp.) high-purity, gas-free iron. The total gas content (N2 + O2 + H2) given was less than 0.026 pct, and the carbon content, less than 0.005 pct. Spectrographic analysis of a 2 in. cast ingot showed the percentage of metallic impurities as 0.0004 pct Cu, 0.0002 pct Mg, 0.001 pct Mn, 0.01 pct Ni, and 0.006 pct Si. A 1 in. thick slice was cut off from the 2 in. cast ingot. It was hot-forged at 850 °C to destroy most of the cast structure. Surface scale was removed by milling the forged piece to a size 2 in. long, 1½ in. wide, and ¾ in. thick. After normalizing at 915 °C for 15 min, the piece was alternately cold-rolled 40 pct and annealed at 750°C in hydrogen to a final thickness of 0.165 in., with a resulting uniform grain size of 0.1 mm.

Jan 1, 1958

By E. P. Abrahamson II

The effect of transitiorz element bitzary solid solution additions upon the recrystallization temperature of columbium has been investigated. The elements Mn, Fe, Co, Ni, W, Re, and 0s OWY the yecystallization tempel-aturye, while Ti, V, CY, zr, Mo, Ru, Rh, Pd, Hf, Ta, W, Ir, and Pt mise it. A correlation is kloted between the rate of chatzge of recyystallization tewaperature with atomic hercent solute and the free atom electron configuration of the solute element. The work of Abrahamson and Grant1 has indicated a correlation between the free atom ground-state electron configuration and the change in brittle-ductile transition temperature per atomic percent solute in chromium base alloys. A similar correlation was observed for the change in the recrystallization temperature of iron base alloys by Abrahamson and Blakeney and Abrahamson. It was also observed that the limit of rapid change in recrystallization temperature also Correlated with the electronic configuration of the free solute atom. A further study by Abrahamson4 established the generality of the phenomenon by yielding similar results for vanadium base dilute alloys. It has been inferred that a peri- odicity might be expected with changes in the free atom electron configuration of the solvent element. This study is the third set of transition base metal systems to be studied. It is the object of this and further studies on transitional metal systems to detect any systematic variations in the observed correlation which might contribute to the understanding of the electron interactions which are evidently exhibiting themselves. PROCEDURE All alloys were made using 99.9 pct Cb with 0.030 Ta, 0.016 0, 0.0025 H, 0.003 Mo, 0.021 Fe, 0.005 C, and 0.002 N. The solute elements were 99.9 pct pure. According to the published binary phase diagrams5 and metallographic examinations at X750, all additions were in solid solution. The alloys were arc melted and remelted 6 times in the form of cubic 400-g buttons under an argon atmosphere. They were then hot forged at 1200oC to 0.6-in. diameter, annealed for 3 hr at 1200o under argon, and furnace cooled. The specimens were then machined to 0.400 -in. diameter. Grain size was checked and found to remain essentially constant at 150 i 30 grains per sq mm. The specimens were then cold swaged to 0.187-in. diameter, yielding 46 i 1 pct cold work. All alloys were chemically analyzed for the major solute. Analyses of random samples indicated that the impurity content remained at the values of the starting material. Tungsten contamination was held to 0.007 pet.

Jan 1, 1962

By T. A. Rickard

The writing that is effective is woven with a fine texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned 'Itreatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of trans¬mitting thought from man' to man. To be understood beyond question, you should know not only what your words denote but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. ' A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home: The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called `syntax'; and from the original Greek form, ouvaeis (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By Herbert H. Uhlig

ALTHOUGH the mechanical properties of high-carbon manganese-iron alloys, particularly the Hadfield manganese steels, have been established, the literature discloses discrepancies in the reported properties for the low-carbon alloys. Hadfieldlo summarized the existing data up to 1927, including the investigations of Guillet, Arnold, Strauss, Burgess and Aston, and reported his own values for alloys containing for the most part from 0.06 to 0.15 per cent carbon. He noted: From these comparisons it will be seen that while there is a broad and general agreement as to the character of the alloys at the different manganese percentages, there are disparities in individual cases, especially as regards the degree of toughness or brittleness displayed by an alloy with certain percentages and with particular types of treatment. These differences are not always readily explainable. Ib His data showed that alloys containing 4 to 10 per cent manganese water-quenched from 1000°C. were brittle and hard with maximum brittleness at about 7 per cent. Slight improvement in ductility was obtained with compositions from 10 to 17 per cent manganese. Alloys containing up to 17 per cent manganese slowly cooled rather than quenched from 870°C., he found, were slightly improved in ductility with significant improvement in alloys analyzing 4.1 and 4.8 per cent manganese. Recently Walters, Kramer and Loringa reported mechanical properties for alloys made up from electrolytic manganese and ingot iron and containing from 0.02 to 0.04 per cent carbon. They showed that a tempering treatment at 540°C. (1000°F.) for one hour significantly improved the ductility of compositions ranging from 6.7 to 20.7 per cent manganese. The differences of these compared with Hadfield&apos;s results they considered to originate in this tempering treatment plus the fact that Hadfield&apos;s alloys contained higher carbon and phosphorus (0.06 to 0.15 per cent C; 0.06 to 0.07 per cent P compared with 0.02 to 0.04 per cent C, <0.001 per cent P). In this paper it is shown that of the low- carbon alloys (0.02 to 0.03 per cent) containing from 3.3 to 21.5 per cent manganese moderately or rapidly quenched from 1000°C. some are brittle or ductile, depending on presence or absence of hydrogen. Hydrogen is readily absorbed at high temperatures, and much of it is retained when the alloys are cooled to room temperature. The presence of hydrogen in the range of composition from 10 to 18 per cent manganese is a major factor in determining relative ductility. At 22 per cent manganese, and also at compositions below 10 per cent manganese, factors other than or in addition to hydrogen play a role. These are discussed. Also data are presented to show that hydrogen absorbed by the high-carbon alloys of Hadfield composition is without effect on their mechanical properties.

Jan 1, 1944

September 28, 1915. The Nominating Committee of the American Institute of Mining Engineers has the honor to present the following nominations for officers of the Institute to be voted for at the 1915 Annual Meeting: For President: L. D. Ricketts District 0 For Vice-Presidents: Karl Eilers District 0 James MacNaughton District 4 For Directors: Thomas B. Stearns District 7 Charles F. Rand District 0 Charles W. Goodale District 5 Edwin Ludlow District 2 George D. Barron District 0 F. W. BRADLEY, Chairman.

Jan 11, 1915