Search Documents

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By David Ziegler

Rough sketches, field notes, an on-site conference or a phone call may no longer suffice to establish your blast plan at a job site. More and more, general contractors, site supervisors, owner re p resentatives, or the owners themselves want to know details about proposed drill and blast operations at their site, in advance. We are seeing more contracts that re q u i re a blasting plan to be submitted in writing. The purpose of this session is to discuss items that you might want to include and address in a written blast plan, and some ideas about how to present them. This is not intended to be a complete list of items that could be included in a blast plan. Contracts may list specific items that need to be addressed. Only a few of the more common elements will be covered here. The bro a der purpose of this discussion is to get you thinking, about what you might want to include in your own “standard ” blast plan.

Jan 1, 2004

By L. C. Reese

? Good construction and inspection presumed. ? Capacity-computation factors are independent of construction method. ? To account for variable or uncertain site conditions, anticipated construction problems, and/or minimal inspection, increase factor of safety. ? Conduct load tests and/or develop easily implemented design alternates (e.g., straight shaft in case bell can't be formed) to reduce factor of safety.

Jan 1, 1988

By Ronald T. Mayerle

A mineral survey of portions of two contiguous WSAs (Wilderness Study Areas) along the South Fork Owyhee River in southwestern Idaho and north-central Nevada was done by the U.S. Bureau of dines in 1984. The portions of the WSAs, known as study areas, have a combined area of 47,610 acres. The Idaho study area consists of 42,430 acres of the 42,510-acre South Fork Owyhee River WSA (ID-16-53). The Nevada study area consists of 5,180 acres of the 7,840-acre South Fork Owyhee River WSA (NV-010-103A). The Idaho study area is within the Boise District of the Bureau of Land Management, and the Nevada study area is within the Elko District. In the Nevada study area, no claims or hard rock mineral occurrences are known.

Jan 1, 1986

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/ lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By Gerasimenko MP

The authors consider the features and advantages of a new promising trend in mineral processing - column flotation. Design aerohydrodynamic and process characteristics of pilot-scale columns are studied. Optimum process parameters for various ores and operations are studied. Flow patterns in cells of various cross-sections are investigated and the relationship between Peclet criterion and specific capacity of cell is determined. On this basis options were developed for optimisation of hydrodynamic characteristics of large capacity cells, including longitudinal sectionalising of the collection zone. It is shown that advantages of high column cells (10 - 13 m) produced in the West can be implemented in a sectionalised machine of smaller height (5 - 6 m). Investigations on the influence of slurry and air bubbles flow patterns indicated that to increase flotation rate of particles of various flotabilities it is expedient to combine co- and counter-current flows of phases in a single column. The proposed designs allow tailings to repeatedly return tailings to the collection zone and alternate co- and counter-current slurry and air flows. For the first time columns with alternating slurry flows (combination of co- and counter-current flows) are developed and commercialised. Unique multi-sectional cells having a number of essential advantages compared to monocells are developed. Design features of the cell allow: implementation of different flotation process flowsheets in a single unit, improved beneficiation process results, reduced specific power requirement, and elimination of sludging of the aerator and cell bottom part. Operational problems restricting introduction of column cells are connected with the aeration unit. The new cells are supplied with pneumohydraulic and stepped airlift spargers, allowing control of bubble size distribution with a service life of not less than three years. Successful operation of the new generation of columns with cell volumes of 15, 25, 40, and 80 cu m and the height of 5 - 6 m in copper, molybdenum, antimony, tungsten and nickel ores and coal slurry processing at different plants in this country illustrated their considerable process and operational advantages and verified the proposed options and relationships. A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calculating the design of commercial-scale columns is developed.

Jan 1, 1993

By Willem Le Roux

Occupational health and safety is regulated by statute and common law. South Africa has, like many other countries, legislated extensively on occupational health and safety. Despite the body of legislation, the common law continues to play an important role as far as it concerns contractual, delictual and criminal liability. Two major Acts regulate occupational health and safety viz. the Occupational Health and Safety Act, No. 85 of 1993 (?OHASA?) and the Mine Health and Safety Act, No. 29 of 1996 (?MHSA?). The MHSA applies to mines and works as defined and related aspects. OHASA applies to other industries but does not apply to employers and workplaces to which the MHSA and certain matters covered by the Merchant Shipping Act, No. 57 of 1951 apply. See section 1(3) of OHASA. 2 The employer?s health and safety obligations in terms of the MHSA 2.1 Section 2(1) of the MHSA provides amongst others, as follows: ?The employer of every mine that is being worked must: (a) ensure, as far as reasonably practicable, that the mine is designed, constructed and equipped: (i) to provide conditions for safe operation and a healthy working environment (ii) ... (b) ensure, as far as reasonably practicable, that the mine is commissioned, operated, maintained and decommissioned in such away that employees can perform their work without endangering the health and safety of themselves or of any other person?.

Jan 1, 2011

By Fun-Den Wang

Rock bolting has become a major method of coal mine roof support because of its effectiveness, economy, and convenience. The polymeric-resin-bonded bolt has generally proved to be more effective than the mechanically anchored bolt, but the higher cost of the resin bolt limits it to applications where the increased support is essential. The low-cost high-early-strength cement grout developed during this project will encourage more widespread use of fully grouted roof bolts provided practical installation techniques can be developed. Laboratory tests of four types were performed on various rapid-set and accelerated cement products to find a material with properties suitable for replacing resins. A proprietary gypsum cement was ultimately used with good success. A field test of the cement grout was made in an operating coal mine. An intersection was bolted in the standard pattern with cement-grouted bolts and instrumented. A nearby resin-grouted intersection was also instrumented and observations were carried out in both intersections for 2 months. No substantial difference was found between the support provided by the cement and the resin.

Jan 1, 1976

By M J. Begbie, P C. Keall, M P. Simpson

The Golden Cross low sulfidation epithermal deposit occurs in pervasively altered andesite of the Waipupu Formation and in the Waiharakeke Dacite. The unaltered, post-mineral Whakamoehau Andesite overlies these units. The Empire zone of the Golden Cross deposit contains a stockwork which is currently mined by open pit methods, and a series of veins that are mined underground. Alteration envelops both the underground and open pit mineralisation. The core of the alteration zone contains silicification, as quartz veins, and adularia. Shallow portions of the system contain illite-smectite and a thermally unstable chlorite, tentatively identified as corrensite, which pass downward into illite and chlorite, respectively. Replacement calcite occurs widely throughout the altered zone; pyrite is nearly ubiquitous. This alteration assemblage indicates formation from near-neutral alkali chloride waters. A late, post-mineralisation alteration assemblage of calcite, smectite, illitesmectite, kaolinite and siderite presumably formed from weakly acidic, steam-heated CO2-rich waters.   We have identified eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren.  

Jan 1, 1997

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth's crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

The inquiry into the explosion at the Moura No. 2 Mine in August 1994 recommended -?Emergency procedures should be exercised at each mine on a systematic basis, the minimum requirement being on an annual basis for each mine.? (Windridge et al. 1996). In December 1996 the ?Approved Standard for the Conduct of Emergency Procedures Exercises? was published and has been subsequently revised (Queensland Department of Mines and Energy Safety and Health Division 1999). This document provided guidelines for conducting mine site emergency exercises as well as the requirement for a test of state-wide emergency response by holding a Level 1 Mine Emergency Exercise at one mine on an annual basis. From 1998 to date (January 2008) ten Level 1 Mine Emergency Exercises have been held in Queensland, Australia. This paper discusses each of the exercises conducted to date as well as the logistics, scenario preparation, planning and organising required to conduct emergency exercises at this level.

Jan 1, 2009

By P. H. Morris

Nineteen field trials of the co-disposal of fine coal tailings and coarse coal wastes were conducted at the dual Goonyella-Riverside mine in Queensland and at the Hunter Valley No. 1 and Warkworth mines in New South Wales, Australia. The profiles of and the sorting that occurred on the co-disposal deltas are described and an existing theory of subaerial deposition, originally developed for mine tailings alone, is shown to apply to the co-disposed wastes. This enables the dimensionless profiles of large deltas, which may take years to deposit, to be predicted from data obtained from a small delta formed in a few days or even hours

Jun 19, 1905

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010