Search Documents

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By D. Newman

Multiple seam mining is prevalent in Southern Appalachia because economically mineable coal seams are numerous and frequently occur in close vertical proximity. West Virginia, Kentucky, and Virginia have 117, 55, and 40 mineable coal seams respectively. It is extremely rare to have an underground mine that has not been undermined, overmined, or has mining adjacent to it. In many cases the multiple seam mining is concurrent with extraction sequenced in superjacent seams. Because underground mining is focused on recovering the most valuable reserves, mining is rarely practiced from the top seam down, which is the practice most conducive to stability. The combination of room-and-pillar mining methods that include development only, small block, partial retreat, full retreat, and longwall mining produce a wide range of mining geometries and complexity in underlying and overlying seams. In the future, the number of multiple seam operations will increase as reserves are depleted and future mines are, by default, located closer to abandoned mine workings. The improved coal market has transformed many formerally uneconomically mineable seams into attractive reserves. The approaches and methodologies used for multiple seam stability analysis are dictated by the site conditions, including overburden/interburden thickness and lithology, mining geometry, and the mining methods in both the active and abandoned mines. Multiple seam stability analysis using analytical and numerical methods is illustrated by two case histories that reflect close proximity room-and-pillar mining and mining in bump prone situations.

Jan 1, 2007

The works of Metal Manufactures Ltd are situated at Port Kemblam NSW, within a few hundred yards of a deep-water harbour. At present they occupy about 26 acres, and ample provision has been made for future extensions. Rail connection exists between various parts of the Works and the main South Coast Railway, the harbour jetties and the adjacent copper refinery of The Electrolytic Refining and Smelting Co Ltd. A plan of the works is shown in Fig 1.The company was incorporated in March 1916, and commenced production of copper wire in June 1918. Early in 1920, tube manufacture was undertaken, followed by telephone cable mnufacture in 1923. Today the Works consist of five principal sections: Founrdy, Tube Factory, Wire Factory, Cable Factory and Case and Drum Factory. Whilst the last four are engaged in producing the finished materials for despatch from the Works, the first-mentioned is engaged in producing copper, brass, and other non-ferrous billets for use in the Tube and Wire factories. In addition, there are Engineering and Metallurgical Departments supporting the manufacturing sections, and in these, as well as in all other sections of the Works, extensions have been carried out from time to time to provide for increased output and new types of products.

Jan 1, 1938

By Mark P. Meyer

During 1991 through 1993, the U.S. Bureau of Mines (Bureau) -Alaska Field Operations Center (AFOC) in cooperation with the Bureau of Land Management (BLM) -Arctic District Office and the State of Alaska, Division of Geological and Geophysical Surveys (ADGGS), conducted exploration, geological, geochemical, geophysical, mineral resource, and mineral potential investigations in the 6.7 million hectare Colville Mining District (CMD) study area. This mining district study area, located in northern Alaska, includes the Colville River drainage basin as well as 0.35 million hectares of the southern part of the National Petroleum Reserve in Alaska (NPRA). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district program. The Bureau's MLA mining district program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies.

Jan 1, 2011

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By G. F. Carr

"IntroductionFLUORSPAR has been found at several •localities in Newfoundland, but all the commercial deposits discovered to date are in the vicinity of St. Lawrence, a town on the southeast coast. Most of the veins are within six miles of St. Lawrence harbour, and between sea-level and an altitude of 400 feet. The St. Lawrence Corporation of Newfoundland, Limited, and Newfoundland Fluorspar, Limited, a subsidiary of the Aluminum Company of Canada. Limited. are the two producers.With the arrival of 1953, the St. Lawrence area entered upon its twenty-second •consecutive year as a producer of fluorspar. Production has increased more or less steadily during this period, as is shown by the fact that approximately one-half of the total shipments to date have been made during the past six years. Between four and five hundred men are employed by the industry, and more than $1,250,000 was paid out in wages and salaries during 1952. Shipments during that year reached an all-time high of 81,283 tons valued at $2,484,943, compared with 67,925 tons valued at $1,966,477 in 1951 (1).As a result of an agreement made in July, 1952, with the United States Defence Materials Procurement Agency, production of the St. Lawrence Corporation, Limited, and St. Lawrence Fluorspar, Incorporated, an affiliated company, will •be increased by .approximately 50,000 tons of acid-grade fluorspar per year. The contract extends over a period of four years, or until 150,000 tons of acid-grade concentrates have been produced."

Jan 1, 1954

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By Wilson Bardales

El presente trabajo describe la experiencia de la Gestión de la Calidad en la Cía. Minera Poderosa S.A., específicamente en el rol que desempeñan los Círculos de Mejoramiento Continuo (CMC´s) como un vehículo efectivo para alcanzar los objetivos de la empresa. Los CMC´s están integrados por trabajadores de un mismo proceso, a quienes se capacita en el manejo de herramientas, técnicas y metodologías de la calidad, con la finalidad de realizar mejoras en los procesos. En ese sentido, en la compañía minera La Poderosa, la administración es participativa y el directorio difunde las políticas, para lograr la rentabilidad de la empresa. Así también, los mandos medios definen los objetivos y estrategias, desplegándola en cascada a la supervisión y estos a su vez, al personal de línea. Este concatenamiento de responsabilidades y la participación de los CMC´s aseguran el alineamiento y control de la gestión.

Sep 12, 2005

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

This paper describes the methods of constructing timber barricades against pillars of ore in the South Mine, property of Broken Hill South Limited, Broken Hill, N.S.W., and discusses the behaviour of the various types of barricade alongside trucked sand filling and hydraulic stowed sand filling.Since the introduction of hydraulic stowing, cut and fill and overhand square letting methods have been used in mining the pillars. Such methods could not be used where the pillars had failed badly. The filling used is partially deslimed concentrating millresidue containing among other gangue minerals, calcite and a small amount of pyrrhotite and pyrite.The author is indebted to the mine superintendent of Broken Hill South Limited for permission to publish this paper.OLD METHODS OF CONSTRUCTING BARRICADES.Square Set Stopes.Before filling each stope the outer row of legs was lined inside with 10 in. x 2 in. boards spaced 2 in. apart. It was usual to tie the row of legs and caps together with timber dogs. As the space between the barricade and ground varied from nil to several feet, it was general practice to fill behind the lining boards. No provision was made to retain this sand during subsequent pillar stoping, consequently a run of sand right up the barricade could cause adilution of ore and serIOUS dIstortion of the barricade.

Jan 1, 1946

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By A Raza, D P. Kohn, D A. Foster, A J. W Gleadow

A large and increasing data base of apatite fission track results from sedimentary and granitic rocks exposed within the south-eastern highlands and along the continental margin ofAustralia provides constraints for the tectonic development of the south-eastern passive margin. The fission track results suggest that many regions of the south-eastern margin of Australia experienced distinct episodes of relatively rapid cooling during the middle Cretaceous to early Tertiary that can be attributed to the effects of rifting. One cooling episode is middle Cretaceous in age and related to denudation of the south eastern highlands from Tasmania to northern New South Wales between ~90 - 100 Ma. Rocks exposed along the present coast line record a later episode of rapid cooling, which is diachronous and decreases in age northward from ~80 to 90 Ma in northern Tasmania to southern New South Wales, ~60 - 80 Ma in central and northern New South Wales, and to ~50 - 60 Ma in southern Queensland. The results are consistent with models suggesting that underplating occurred inward of the rift along the eastern margin of Australia as a result of the onset of continental extension in the Tasman Sea at ~96 Ma. This resulted in a significant change in base level and km-scale denudation of much of the southeastern highlands. Subsequently, as breakup commenced during the Late Cretaceous at ~80 Ma and continued into the Paleocene at ~60 Ma, the second stage of cooling was imprinted on the rocks along the margin. This cooling is probably due to the relaxation of elevated geothermal gradients associated with rifting as well as some denudation. Because rifting was oblique to the present-day coast, different regions record different ages of cooling associated with the rift. The southern regions of New South Wales and Victoria yield ages associated with earlier rifting while regions of northern New South Wales and southern Queensland give ages associated with later rifting.

Jan 1, 1995

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By Bengt H. Fellenius

THIS PAPER deals with the analysis of results from axial testing of vertical single piles, i.e. the most common field test per-formed. Despite the numerous tests which have been carried out and the many Papers which have reported on such tests and the analysis thereof, the understanding of pile test loading in current engineering practice leaves much to be de-sired. The reason for this is that the engineers have concerned themselves with mainly only one question: "Does the pile have a certain least capacity?", finding little of practical value in analysing the actual capacity and the pile-soil interaction. This Paper aims to show that engineering value can be gained from elaborating on a pile test ? during the actual testing in the Held, as well as in the analysis of the results. The first portion of the notes make use of an earlier Paper by the author (Fellenius. 1975). However, additional views and recent literature have been incorporated.

Jan 1, 1988

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Ron Millions, J. A. Folinsbee, Ishwinder Grewal, Michael Fullam, Don Strickland, Tony Y. Chong

"Since milling began in 1912, the Dome mill, now part of the Porcupine Joint Venture (PJV), has been expanded several times, the most recent increasing the milling rate from 3,500 to 11,500 tonnes per day. Dome uses conventional crushing and grinding followed by gravity concentration to recover free milling gold. A cyanidation/CIP process recovers the remaining gold in the gravity tails.Over the past few years, continuous gravity improvements have increased the gravity recovery from 20% to nearly 50% of the plant feed gold. This paper describes some of the factors that have contributed to this dramatic increase, and suggests how gravity recovery can be further improved. Gravity circuit availability has been improved to >98% with the implementation of a preventative maintenance program. More Knelson concentrators have been added to the circuit, and in 2002, an Acacia Intensive Leach Reactor was installed to replace the shaking table. In 2003, the entire gravity circuit was audited to evaluate and quantify the circuit performance. The metallurgical and mechanical operating conditions of the gravity circuit are now well understood, and areas for further improvement are well defined.INTRODUCTIONThe Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. One of the goals of the JV was to use the milling capacity of the Dome mill to process ore from Placer Dome and Kinross mines in the Timmins Camp. The PJV Dome Mill utilizes gravity concentration, cyanide leaching and carbon in pulp gold circuits to recover gold. Gravity recovery has been used in some form at the Dome Mill for most of its existence, first using conventional jigs, these being replaced in 1993 by two Knelson Concentrators, one for each of the two grinding circuits in the Dome mill. Over the years more concentrators have been added to improve the gravity recovery, most recently in 2002 for a current total of five. Also in 2002, an Acacia Intensive Leach Reactor was added to process the Knelson concentrate, replacing the shaking table."

Jan 1, 2004