Search Documents

By Chi Ru?an

Sollutions of ammonium chloride, nitrate and sulfate were studied in extraction of rare earths absorbed on a low-grade, kaolilnitic ore recently discovered in southern China. The results of percolation leaching tests and the recovery of the rare-earth values from these solutions are presented.

Jan 1, 1989

By Song Ning

The main mineral constituents of phase-transformed chalcopyrite are CuS and FeS2. CuS is more soluble than FeS2 in an acidic CuCl2 solution with presence of excessive NaCl, so that FeS2 could be removed as solid residue from a leached solution. The experimental results showed that the efficiency of the copper leaching is heavily determined by the following two factors: a) The degree of the chalcopyrite phase transformation to CuS and FeS2 b)The concentration of Cl during the leaching, specifically whether there is enough excessive Cl existed. I t was found that when the Cl in the solution is not excessive, the slowest step of the leaching is the dissolution of Cu2Cl2.

Jan 1, 2006

By John L. Uhrie

Oxide stockpile leaching operations can realize increased copper recovery and decreased acid consumption from in-situ generated acid resulting from the oxidation of intentionally introduced pyrite recovered from mill tailings or other sources. While all oxide leach ores can benefit from pyrite addition, low acid consuming ores can show remarkably increased recovery and net acid generation; however, more highly acid consuming ores will show benefit more exclusively through increased copper recovery. Additional work shows that the value of highly acid consuming ores can be optimized by balancing copper recovery against acid consumption.

Jan 1, 1999

By Tian Li

Molecular crystal growth during gibbsite precipitation from caustic aluminate solutions under different flow regimes was investigated in three different laboratory precipitators. The gibbsite precipitation experiments were conducted at the same temperature, initial liquor composition and seed type. The Taylor-Couette precipitator and the stirred tank precipitator were operated, respectively, under the laminar and turbulent flow regimes, while the bottle roller precipitator was operated in a complex flow regime, where fluid flows are generated by the end-over-end rotation of the bottles. Comparison of the growth rate estimates from the different flow regimes showed good agreement, which suggests that the hydrodynamic regime has little or no effect on gibbsite crystal growth under the operating conditions employed in this work. The growth rate estimates from the current precipitation study showed a second order dependency on supersaturation and is consistent with a screw dislocation growth mechanism. The findings of the current work are in agreement with previous gibbsite crystal growth studies published in the literature.

Jan 1, 2003

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Alexandr I. Volkhin

It is practically useful to separate copper from nickel at the fire refining stage of blister copper by transferring nickel in electrochemical inert silicides which are being concentrated further into the tank-house slimes. The treatment of copper melt by silicon-containing reagents is resulted in lowering the interfacial tension of the melt, its deoxidizing, selective siliconizing of in-melt nickel and forming a by-product with fluxing properties. Si-containing reagents have positive influence on results of fire and electrolytic refining, and further pulverizing of copper in plant conditions.

Jan 1, 2006

By Xie Gang

The leaching experiment used by bacteria on the low grade sulfide copper ore which is difficult to leach was carried out. Some leaching bacteria which have good physiological and leaching activity were isolated and domesticated, and were adapted to leaching ore. The effective domesticated method was put forward. Some technological parameters such as ore acidification, potential controlling, leaching method, ore granularity, leaching acidity, leaching liquid quantity and acid consumption were obtained by column experiment and leaching ore in situ under the ore well. The results show it could leach 30.62% of copper from the low-grade sulfide copper ore within 24 weeks by column leaching method, and the bioleaching rate of copper is 22.83% by leaching in situ under the ore well in 8 months.

Jan 1, 2006

By T. Taniguchi

The existing Mitsubishi Process line at Naoshima Smelter and Refinery has been operating successfully since 1991, and its present production capacity is 270,000tpy of copper. Furnace relining works have been carried out every two years to coincide with the compulsory bi-yearly boiler inspection, but the next target is to extend the furnace refractory life to four years, while still undergoing the mandatory boiler inspection every two years. Although the damage of hearth bricks beneath lances in the Smelting furnace was a matter of concern, it was reduced by controlling gas velocity and evening solid distribution to each lance. The life of bath level bricks in the Converting furnace was also a concern, but four-years continuous use of the bricks was achieved in the course of the last two campaigns. Several other improvements were also carried out to the cooling systems during the shutdown in 2005 to ensure longer campaign life. This paper summarizes recent improvements implemented to enhance the advantages of the Mitsubishi Process.

Jan 1, 2006

By Oleg I. Platonov

Method of high-temperature reduction of oxygen-bearing sulfurous gas has been developed at Copper Plant (CP) of MMC ?Norilsk Nickel? Trans-Polar Division (PD) with the aim of producing elemental sulfur from Vanyukov furnace? off-gas. Non-explosive reduction technology of oxygen-bearing sulfurous gas by methane utilized at Copper Plant has been designed to separate the processes of gas heating and sulfur dioxide reduction based on different kinetic of the reactions oxygen fixing and SO2 reduction. First, natural gas promptly reacts with oxygen contained in the process gas to heat a gas mixture up to the temperature of sulfur dioxide reduction (1200C). Then isothermal reduction takes place within 1 sec. Combustion chamber (pre-chamber) design developed based on the above principles is presented. Practical experience of the two reduction reactors operation at CP since 1996 proves high efficiency of the developed reduction process. The volume efficiency rises dramatically thanks to the fact that both fuel and reducing agent are fed into the reactor volume in the form of high-speed turbulent jets providing an intensive mixing of the reacting gases. On condition of equal internal volume of the reactors, the developed process offers higher efficiency of reagent interaction resulting in sulfur conversion exceeding 90%, as compared to the equilibrium one.

Jan 1, 2006

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Roberto Javier Santiago

The diferent applications of the Calcium Carbide in the steel plants are described in this paper, trying to give advantages in their use.

Jan 1, 2006

By Ross McClelland

This paper provides a technical overview on the installation and commissioning of the Ausmelt lead smelting, slag reduction and slag cleaning operations at the HZL Chanderiya site in India. It also discusses theoretical concepts behind the process practices currently in place at HZL.

Jan 1, 2006

By Seyed Mohammad Taghavi

In this report, the efficacy of different factors such as temperature of reaction, time of reaction and depth of bed are investigated in a process of recovery of zinc oxide from zinc ore concentration residues in a fluidized bed furnace. Under optimum conditions, there was more than 93.5% zinc oxide in products.

Jan 1, 2006

By David M. Beckwith

Increased globalization and outsource manufacturing complicate the procurement and enforcement of intellectual property rights on a worldwide basis. Recent legislative and case law developments in the United States highlight the importance of a multinational intellectual property strategy. IP lawyers David Beckwith and John Hankins will discuss planning and pitfalls in this rapidly changing trans-border environment. Topics to be discussed include harmonization with international patent laws, protecting your technology and market space with a comprehensive approach to IP, and patent enforcement issues relating to import/export of products and components in the United States.

Jan 1, 2006

By Wenshan Zhang

This paper described the present status of China electrolytic manganese industrial production. Electrochemical reactions on cathode and anode, the major technological process, technical requirements on the production and technical index and quality control of the products and the ways of increasing current efficiency during Manganese electrolytic process have been expatiated.

Jan 1, 2006

By José García-Antón, Valentín Pérez-Herranz, José Luís Guiñón, Henry Reyes

"The majority of chromium electroplating operations employ Cr(VI)-based baths. During these processes, Cr(VI) is reduced to Cr(III). Besides Cr(III) other undesirable impurities are present such as iron, copper and nickel. The build-up of the impurities limits the lifetime of the plating solutions. Since the disposal of spent chromic acid baths is expensive and can cause significant environmental degradation, there is increasing interest in finding ways to regenerate waste chromium liquors.In this work, an electrolytic cell separated by microporous ceramic diaphragms was used to regenerate chromium plating solutions. The effect of the ceramic diaphragm structure parameters, such as porosity and pore size, on the performance indicators of the electrochemical reactor (fractional conversion, current efficiency, product yield, specific energy consumption) was investigated.The fractional conversion, the product yield and the current efficiency increased and the specific energy consumption decreased with the decrease in porosity.IntroductionChromic acid is widely used in industrial applications such as steel manufacture, metal finishing industries, aluminium anodising, pasivation of cadmium, magnesium, and zinc, etching of plastics and another industrial operations related with processing ferrous and no ferrous metals [1]. These processes employ baths with high concentrations in chromic acid, about 180 and 350 g/L, where hexavalent chromium is reduced to Cr(III):"

Jan 1, 2008

By Roberto Javier Santiago

This paper tries to make a study about the use of calcium carbide during the tapping in replacement of part of the aluminum used in the furnace tapping, analyzing theoretical consumptions and then transfering the practice to the plant.

Jan 1, 2006

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006