Search Documents

By M. Jahazi, P. P. Bhattacharjee, K. Chadha

The present work investigated the effect of strain reversal during high pressure torsion on the evolution of microstructure, texture and hardness properties of two different materials with different dynamic recovery behavior, namely, high purity (99%) Aluminum (2N-Al) and Aluminum-Magnesium (Al-2.5%Mg) alloy. In the two aluminum alloys subjected to different routes, the evolution of the ultrafine structure followed same trend. At lower strain level, sub grains with prominent LAGBs network were observed and at higher strains, ultrafine equiaxed grains separated by HAGBs were observed throughout the disk. The texture evolution in monotonically and strain reversal processed 2N-Al and Al-2.5%Mg showed presence of typical torsion texture components at different strain levels. The strength of the components was observed to follow different trends depending on the processing routes.

Jan 1, 2015

By M. Misra

The volume of low-level contaminated soil at the. Department of Energy's Nuclear Weapon Sites are in the order of several million tons. Most of the contaminants are uranium, plutonium, other heavy metals and organic compounds. Selected Physical separation processes have shown demonstrated potential in COD Centratingthe radio nuclides in a small fraction of the soil. Depending upon the size, nature of bonding and distributions of radio nuclides, more than 90 percent of the radio nuclide activity can be concentrated in a small volume of fraction of the soil. The physico-chemical separation processes such as flotation in a mechanical and microbubble tall column cell have shown, promising applications in cleaning up the high volume contaminated soil.

Jan 1, 1995

By Dmitri Goljandin, Jaan Kers, Xiangjun Zuo, Lifeng Zhang, Priidu Peetsalu

"In this paper, the mechanical milling of the electronic wastes was carried out. The metal parts and plastic parts were roughly separated. The final plastic powder size could be as small as ~100 µm. Then the pyrometallurgical recycling Printed Circuit Boards (PCB) was executed. The mechanisms of thermal degradation and combustion are investigated using TG/DTA and MS. Some chemical powders, such as Na2CO3, NaHCO3, NaOH and CaCO3 are used to control the exhausted toxic gas such as Br2. Introduction Waste electric and electronic equipment (WEEE), or electronic wastes (E-wastes), has been taken into consideration not only by the government but also by the public due to their hazardous material components [1-3]. From the point of material composition, electronic wastes can be defined as a mixture of various metals, particularly copper, aluminum, and steel, attached to, covered with, or mixed with various types of plastics and ceramics [4]. Precious metals have a wide application in the manufacture of electronic appliances, serving as contact materials due to their high chemical stability and their good conducting properties. Platinum group metals are used among other things in switching contacts (relays, switches) or as sensors to ascertain the electrical measurand as a function of the temperature [5]. Table 1 [6] gives examples of the metal composition of different electronic scraps from literatures. Additionally, non-ferrous metals and precious metals content have gradually decreased in concentration in scraps. The value distributions for different electronic scrap samples are shown in Table 2 [6], where the metal price data are from London Metal Exchange (LME) (Octoebr 2007). It can be seen that for cell phones, calculators, and printed circuit board scraps, the precious metals make up more than 70% of the value, for TV boards and the DVD player they still contribute to about 40%. This indicates that the major economic driver for recycling of electronic waste in industry is from the recovery of precious metals. Behind the precious metals come copper and zinc, while Al, Pb, and Fe are less value. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials."

Jan 1, 2008

By Fernando Guevara

Many smelting and slag-cleaning furnaces operate with cooling systems designed to freeze a slag layer over the refractory to protect it. The fluid flow and heat transfer conditions associated with the freeze layer and mushy zones are poorly understood. These phenomena were simulated with a small-scale room temperature, 2-dimensional model, using an aqueous solution of calcium chloride to simulate the slag. Reasonable similarity with conditions encountered with copper and nickel smelting systems was achieved (Pr 50 and Ra 108, in the laminar-turbulent transition). Measurements of the freeze layer development and velocities were made with the Particle Image Velocimetry (PIV) technique. Direct Numerical Simulations (DNS) were also made of the unsteady fluid flow and heat transfer problem. It was found that the solidification process is well described using an improved model for high molecular viscosity in the mushy zone. Solid front growth, isothermal profiles, velocity profiles and heat transfer through the walls showed good agreement between the PIV and DNS results. Experimental and numerical velocity profiles close to the freeze layer show a parabolic behaviour in the vertical velocity profile which is completely different from the calculation of heat transfer using a sharp interface model. The reason for this is attributed to the effects of the mushy zone with a high viscosity and high shear stresses acting on that area.

Jan 1, 2006

By Wen-Ming Chien, Vamsi Krishna Kamisetty, Amrita Mishra, Ivan Gantan, Prathyusha Mekala, Dhanesh Chandra

"The phase equilibrium and characterization studies by using high temperature X-ray diffraction (XRD) and differential scanning calorimetric (DSC) methods have been performed for binary organic thermal energy storage materials. The organic thermal energy storage materials undergo a solid-solid state phase transition before melting which stores large amounts of thermal energy. Two materials [tris(hydroxymethyl)aminomethane(TRIS) and 2-Amino-2-methyl-l, 3- propanediol(AMPL)] were used for this study. Binary samples of AMPL-TRIS were prepared to perform high temperature XRD characterization and DSC studies and the binary AMPL-TRIS phase diagram was developed. The high temperature solid-state phases of AMPL and TRIS were characterized as a disordered BCC structure. It was found there is virtually no solubility of TRIS in AMPL or vice versa below -75 °C. The maximum solubility of TRIS in AMPL is 11% TRIS at 75 °C. The eutectoid transformation was shown at 19%TRIS-81%AMPL composition and at a temperature of 75°C. Lattice expansion calculations on single phase of TRIS and AMPL have been performed.IntroductionThermal energy storage materials can store a large amount of heat due to the presence of thermal transitions from the orientationally ordered to disordered phases occurring before melting. These molecules (such as amine and alcohol derivatives of neopentane) can reorient as a whole about the central carbon atom to form orientationally disordered crystals (ODIC) and their spherical shape makes them reorient relatively easier. Thermal energy storage materials are becoming increasingly important as a renewable energy resource. These molecules undergo large changes in enthalpies at solid-solid transitions. The presence of these compounds with large enthalpy changes are identified as potential thermal energy materials and some of die applications are solar cell systems [1-3]. Binary mixtures have been found as a way to adjust the transition properties in addition to pure compounds [4]. Tris(hydroxyrnethyl)aminomethane (TRIS, C(CH2OH)3NH2) and AMPL, CH3C(CH2OH)2NH2) are two important thermal energy storage materials."

Jan 1, 2012

By Daniel Kim, Michael Free, Justin McAllister, Urian Marshall, Shijie Wang

"Cathode impurity levels of electrorefined copper were evaluated based on 1/10* scale laboratory electrorefining tests. Cathodes were evaluated near the top, mid-section, and bottom sections of cathodes on both the set and mold sides and strip and scrap cycles. Slime weights were measured, and slime and electrolyte samples were also evaluated for impurities. Results from these tests have been compiled and compared to evaluate the effects of changes in operating conditions and electrode location on cathode impurities.IntroductionMany types of impurities are commonly found in commercial copper electrorefining anodes. The smelter operations that produce the anodes process concentrates that contain a wide variety of impurities that vary based on the mineralogy of the ore. Most anode impurities are removed during electrorefining. However, a portion of the anode impurities is incorporated into the copper cathode product. The mechanisms by which impurities are transported from the anode to the cathode are not well understood. Some impurities can be transported as anode slime particles to the cathode where they are incorporated into the cathode. Other impurities can be transported as dissolved species that are electrochemically reduced with the copper to become part of the cathode. Although research has been performed on anode slimes and impurities [1-4], there is a need for additional information regarding the relationships associated with electrorefining cycles, electrode faces, local electrode positions, anode impurities and specific cathode impurities. The objective of this study was to evaluate lead, arsenic, and antimony cathode impurity trends associated with electrorefining cycles, electrode faces, local electrode positions, and anode impurities. A variety of techniques including electrolyte filtering, anode heat treatment, high electrolyte arsenic concentration, high arsenic and/or lead in anodes, flocculation of slime particles, and appropriate current density control were used to vary cathode impurity levels. Each test was performed only once for a strip cycle and once for a scrap cycle. Consequently, the results for the individual conditions are preliminary and are not the focus of this study. However, the collective set of data with varying impurity modifying techniques provides a broad range of impurity levels, and the associated trends with respect to lead, arsenic, and antimony are discussed in this paper. Approximately 180 analyses of copper cathode were used to track the antimony, arsenic, and lead impurities. Eighteen anode slime samples were also analyzed for antimony, arsenic, and lead."

Jan 1, 2012

By D. J. Goodwill

BHP Copper operates a 3,400 tpd dry concentrate, single burner, Outokumpu flash smelting furnace (FSF) at their San Manuel copper smelter in Arizona. The very fine (-325 mesh), dry concentrate is fed to the burner from a 550 metric ton (nominal) capacity furnace feed bin via two drag chain feeders. During the 10-year history of the furnace, operations have been plagued by serious flooding problems. The fine concentrate sometimes becomes aerated during discharge from the bin and flows like a fluid at very high uncontrollable rates to the burner. This results in upset conditions at the concentrate burner leading to poor furnace metallurgy. This paper will examine the problems of uncontrolled feed from the furnace bin (i.e. flooding), and' instantaneously feeding a flash smelting burner. It will show that a drag chain is a poor choice of feeder when high rates are needed, and that drag chains always produce a funnel flow pattern in a bin. BHP's drag chains cause narrow diameter, high velocity flow channels within the stored material. Consequently, there is insufficient residence: time for the concentrate to fully de-aerate before discharge, hence flooding occurs. In addition to the flooding problem, drag chains create a pulsating flow to the concentrate burner due to the tendency for material to slough off in discrete chunks at the discharge end of the slow moving chain conveyor. During the scheduled FSF rebuild in May 1999, BHP intends to remove the drag chains, modify the bin to a mass flow design and to use STAMET® multi-disc feeders to accurately and instantaneously control the rate of discharge from the bins. Air slides will be used' to convey the concentrate to the burner.

Jan 1, 1999

By D. W. Collins

Several organic and inorganic substances are widely used to control deposit structure and morphology during the electroprocessing of copper. Methods for monitoring the levels of thiourea, glue and guar gum during electrorefining and electrowinning have been successfully developed under the trade names of Reatrol and CollaMat. Other instrumental methods have been developed for additives and decomposition products associated with the electroplating of copper and other metals. Generally, these methods have been found to be either insufficiently sensitive or lacking in the desired selectivity for some or all of the additives. These procedures have mostly employed DC techniques; i.e., cyclic voltammetry, Tafel analysis, etc. In this work, chronopotentiometry (CP) and AC voltammetry were used to examine the interaction of glue, guar gum, thiourea and chloride during the electroplating of copper onto a platinum electrode. In addition, the interactions between the additives have been explored. It was found that glue in pure electrolyte (H2S04 and CuS04 only) had no effect on the chronopotentiogram. Glue was only active if chloride ions were present. The addition of thiourea resulted in several different chronopotentiograms depending on the presence of either chloride or chloride and glue. Thiourea used in conjunction with glue and chloride showed a significant increase in the polarization during copper deposition when compared to the electrolyte containing only glue and chloride. The use of a modified channel electrode further increased the sensitivity of CP. The use of AC voltammetry was explored as a technique to monitor some of the additives. AC voltammograms have more spectral detail then their DC counterparts and it is possible to monitor some of the additives at very low concentrations with AC techniques.

Jan 1, 1999

By B. Yalamanchili

Gerdau Ameristeel Beaumont presents its systematic approach for upgrade decisions that has developed over 30 years of ongoing capital projects for quality and cost improvements. This system serves to identify product needs, select process improvement strategies, justify them, and assist multi-department communications and decision-making. This is illustrated with Beaumont mills? last Stelmor upgrade and leads to a discussion of the need to consider Life Cycles of both products and technologies as we move to answer the challenges of the future.

Jan 1, 2006

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya

"This paper focuses on modeling of the scanning laser epitaxy (SLE) process that is currently being investigated and developed at the Georgia Institute of Technology. SLE is a laser-based manufacturing process for the creation of equiaxed, directionally solidified and single-crystal deposits of nickel superalloys onto superalloy substrates through melting and resolidifícation of alloy powders using a scanning laser beam. The thermal modeling of the system, done in a commercial CFD software package, simulates a heat source moving over a powder bed and dynamically adjusts the property values for consolidating CMSX-4 nickel superalloy powder. The associated melting and re-solidification process is modeled using an immediate consolidation approach, and the predicted melt depth is compared with the experimental data obtained. For a given position of the beam, geometrical parameters of the melt pool are used to estimate the resulting microstructure. The influence of the processing parameters on the microstructural evolution is also discussed. This work is sponsored by the Office of Naval Research through grants N00173-07-1-G031, N00014-10-1-0526 and N00014-11-1-0670.IntroductionIn order to increase the operating temperature of gas turbine aero engines, investment cast equiaxed turbine airfoils are now often replaced with airfoils that have either directionally solidified columnar or single crystal (SX) microstructure. Wear and damage during operation limits the lifetime of these components and necessitates the replacement of numerous airfoils within the engines. Due to the high cost of producing SX cast turbine blades, the cost of replacing each blade can be several hundred to several thousand dollars. With each engine containing several hundred blades, the cost to replace all blades can reach hundreds of thousands of dollars. Hence, it is of great interest to develop a process that can restore the single crystal microstructure at the locations of material loss and allow for the blades to be repaired and reused rather than be scrapped and replaced."

Jan 1, 2012

By Roger Agnew

Sulphide ores mined by Inco Limited in the Sudbury District contain small quantities of cobalt. During beneficiation, cobalt distribution to various streams is similar to nickel. After smelting, nickel is selectively extracted by carbonyl refining and the cobalt remains in the carbonylation residue. This residue is processed in a specialized hydrometallurgical plant to produce precious metal residues, copper cathodes, and a nickel- cobalt carbonate intermediate product. The nickel-cobalt is shipped to Port Colborne where the cobalt is separated as cobaltic hydroxide and refined to metallic cobalt. This paper deals specifically with the recently constructed Electro Cobalt Refinery. The cobaltic hydroxide is dissolved and residual zinc, copper and nickel are removed by ion exchange and organics by a carbon column. The purified cobalt solution is fed to the electrowinning circuit where cobalt rounds are produced on stainless steel mandrels. In the design and construction of the refinery, special attention was directed to materials of construction both for the process equipment and the physical plant, operating control and flexibility, and the quality of the working environment. The end result is an efficient and clean operation which yields a product of excellent quality.

Jan 1, 1988

By Richard D. Hagni

Reflected light microscopy is routinely applied to the study of ore minerals and textures in polished sections prepared from a wide variety of ore specimens. With the increasing interest in environmental problems, the important role of the reflected light microscope in the precise phase identifications and the determination of the textural relationships between those phases needs to be recognized. Among other environmental applications, the microscope has been applied to the recognition of lead smelter particles from remote collect sites in Missouri and those particles have been compared to dust particles from specific localities at the nearby lead sinter plant and lead blast furnace. Dust from a secondary copper refinery has been studied for its mineralogy. Soils in the vicinity of a Missouri lead smelter have been studied for their mineralogy in preparation to the clean up of those soils. Electric arc furnace (EAF) dusts, recently classified as hazardous waste by the EPA, have been examined for their mineralogy and textural intergrowth in order to better evaluate proposed metallurgical treatment procedures to render the dust non-hazardous. The initial products from experimental metallurgical treatment of EAF dusts also have been studied to aid in determining the effectiveness of those treatment procedures. Refractory gold sulfides that have been roasted in the presence of lime to retain environmental objectionable sulfur and arsenic while recovering the gold have been studied by RLM to determine their mineralogy, porosity, and permeability for cyanide leach solutions. These case histories illustrate the applicability of ore microscopy to the study of problems related to environmental concerns.

Jan 1, 1995

By A. Filzwieser

The highest current density suitable for the electrowinning process is between 50 to 60 % of its limiting current density. One of the most important influences on the limiting current density is the thickness of the hydrodynamic boundary layer near the electrode surface. Therefore, the fluid flow in a copper electrowinning cell is calculated. The numerical simulation - using the CFD-software package FIRE® - considers all three different types of the fluid flow, namely, the natural convection, the forced convection by electrolyte circulation and the forced convection by electrochemically induced gas stirring. The simulation of natural convection is based on the different density values in the boundary layer at the electrode surface given by a density/concentration correlation. The copper concentration - linked with the current density by Faraday law - is solved by an additional transport equation. The simulation of the forced convection by the electrochemically-induced gas stirring is done by using a real two-phase calculation. That means that all differential equations are solved again for the second phase. The numerical solution of the fluid flow field is compared with the results of LDA- measurements, which were done in a special cell. The software for the LDA enabled a calculation of the void fraction possible and therefore a rough estimate of the mass transfer coefficient through the prevailing gas bubble induced convection can be made by assuming the influence of relative bubble volume.

Jan 1, 1999

By J. A. Sanhueza

The environmental regulations and terms issued by the Chilean Government for all copper concentrate smelters have been a very important reason for permitting project developments that drastically decrease the sulfur emissions due to the pirometallurgycal copper process. A remarkable case of the Hernan Videla Lira Copper smelter, located on the Copiapó Valley and very near some housing-sets of a city of high development, are described. Results of this project's implementation of the control and reduction of off gas emissions, the control and monitoring system, the community conflicts, and the strategy to comply with the demands established by the state environmental institutions, are presented.

Jan 1, 1999

By M. Kawakami

In order to make titanium ingot directly from molten slag, the metal pool was tried to form and used as the cathode. The electro-slag remelting (ESR) unit was used for the purpose. The unit is composed of water-cooled copper mold and the DC power source of 2000 A and 100V. The graphite electrode was used for anode and the base plate was used for cathode. The commercial and re-melted slag of CaO-CaF2 was melted in the mold with the addition of TiO2. The following reactions are expected to occur. Ti4+ + 4e = Ti at cathode 2O2- + 2C = 2CO + 4e at anode During the process, large amount of molten slag splashed out from the mold, showing the CO evolution at anode. The metal deposit was obtained but in the form of block and piled up on the base plate. The metal pool was not obtained perfectly because of shortage of heat supply. The cathodic current efficiency was 60 % at maximum. The metal deposit contained much impurity. In order to reduce the impurity and increase the current efficiency, the effect of electrode distance was examined. The electro-slag re-melting of titanium was tried in order to examine the condition to make metal pool.

Jan 1, 2006

By John A. Gisby

Phase equilibria for multi-component systems can be calculated reliably from critically assessed thermodynamic data for sub-systems using software packages like MTDATA, developed by the National Physical Laboratory, UK (NPL). Models and data resulting from an ongoing Mineral Industry Research Organisation (MIRO) project make such calculations possible for the complex systems encountered during sulphide smelting, involving interactions between matte, slag, metal, and gas phases. Predictive calculations can be made that are directly relevant to industrial processes, covering composition and temperature ranges beyond the scope of hard- copy phase diagram compilations, allowing the feasibility of more economic and environmentally sound routes to be explored, better choice of materials to be made, and pilot plant studies to ,be directed more efficiently. Current applications include the selection of suitable fluxing practices in copper and nickel smelting, analysing the operation of the Kennecott copper smelter, optimising the recovery of precious metals and investigating refractory wear.

Jan 1, 2002

By Shigehito Isobe

The Li-N-H system composed of LiH and LiNH2 catalyzed by titanium compound desorbs ~6 mass% hydrogen and a quite small amount of ammonia in temperature range from 150 to 250 °C under He flow atmosphere. In this work, hydrogen desorption (H-desorption) mechanism in the reaction from LiH+LiNH2 to Li2NH+H2 in a non-equilibrium condition was clarified by TDMS, TG and FT-IR analyses for the products replaced by LiD or LiND2 for LiH or LiNH2,respectively. The results suggested that H-desorption reaction progresses through two-step elementary reactions mediated by ammonia. As a next step, we carefully determined the amount of the ammonia containing in desorbed hydrogen for the Li-N-H system in a closed system from the practical point of view. The results indicated that a quite small of ammonia thermodynamically coexisted in the desorbed hydrogen in closed system, although ammonia could not be almost detected in emitted hydrogen gas by TDMS under some non-equilibrium conditions. Moreover, for understanding the role of titanium, the chemical bonding state of the titanium compounds doped as catalyst in the mixture was examined by XAFS measurement. The results indicate that the Ti atoms, which can induce catalytic effect, are in a particular chemical bonding state.

Jan 1, 2006

By Carlos Schvezov, Eliana Agaliotis, Alicia E. Ares, Mario Rosenberger

"The interaction between a solidification front and a spherical particle was modeled and simulated in order to study the phenomenon of ""pushing"". Finite element methods were employed in axisymetric domains. The drag force is calculated from the calculated fluid flow field and the repulsion force is the Lifshitz-Van der Waal force. The thermal field is decoupled from the force field. The model is applied to a metallic matrix containing particles with similar, lower or higher thermal conductivities than the matrix, resulting in planar, convex and concave interface shapes, respectively.The results show that the critical velocities for pushing for concave and convex interfaces are about one order of magnitude larger and one order of magnitude lower than the critical velocity for flat interfaces, respectively. The simulated results were in very good agreement with reported experimental results.IntroductionThe solidification interface of materials containing spherical particles in some cases can push the particle ahead the interface. This phenomenon generally occurs during the solidification of different materials such as, metallic alloys containing native particles, metal matrix composites containing particles or fibers as reinforcements and crystallization of semiconductor, optical, optoelectronic or biological materials. In all cases the interaction strongly determines the distribution of particles and the resulting physical and physic-chemical properties of the resulting material. The phenomenon has been investigated for many years both experimentally and by mathematical modeling [1-21]. The process is complex due to the variety of phenomena involved during pushing. In all cases, the physical problem depends on the properties, nature, and morphology of the interacting media; the particle, melt and solid; and external fields such as gravity, thermal and electromagnetic fields."

Jan 1, 2012

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999

By Bruce Cavender

Managers are frequently faced with the decision to perform a task or manufacture an object in-house or to hire an outside vendor to perform the function. Outsourcing decisions are usually driven by economics: work is outsourced if it can be completed at a lower cost or in a shorter time than it can in-house. A technique termed incremental analysis can be used to make this decision. Incremental analysis examines the financial impact of outsourcing decisions as a function of the firm's fixed and variable operating costs. To use this tool, individual components of production cost are identified as being either constant or varying with levels of production activity. The assignment of cost type can be made in several ways: though analysis of historical operating data, understanding of individual expense types, and so forth. Changes in fixed and variable costs resulting from each potential course of action are explicitly identified to project the financial outcome of each alternative. The alternative having the greatest positive impact on profit is selected for implementation. By using the fixed- and variable-cost framework, the analysis is conceptually straightforward and substantially simplified. Production managers can therefore use incremental analysis as a tool for fast economically beneficial decisions on a real-time basis.

Jan 1, 1999