Search Documents

By Sylvain Gouttebroze, Mohammed M'Hamdi

In a previous work, a small scale Bridgman furnace has been used to study silicon bi-grain crystallization at different cooling rate. This work expands the analysis by studying the mechanical interaction between the crucible and ingot during the solidification and cooling. The thermal model is based on a 2D-axisymetric heat-transfer model. The flux histories are then transferred to the ingot-crucible 3D-model. Anisotropic Elastic and Crystal Plasticity model are used to model the silicon deformation. Four different assumptions are applied to model the mechanical contact crucible-ingot and three grain misorientations are considered. The results show the strong impact of the alumina crucible contraction on the stresses and deformations in the silicon ingot.

Jan 1, 2015

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By Michael A. Eamon

Magma Copper Company has operated its San Manuel SX-EW Plant facilities since 1986. The original plant facilities have a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solutions from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing leach solutions from an insitu leaching operation. This paper presents a general overview of plant practices with particular emphasis on process innovations developed and implemented by Magma during construction and operation.

Jan 1, 1991

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

By C. E. Dodson

Conventionally hydrometallurgical recovery processes from sulphide concentrates include roasting, leaching, precipitation, impurity removal and zinc electrowinning. The use of the novel (yet commercially proven in other mineral and metallurgical industries) TORBED process reactor for the flash roasting of sulphides will be proposed. The potential advantages in its application will be discussed including very fine particle processing capability, lower cost smaller roasters, waste minimization, improved leaching efficiency and overall process simplification.

Jan 1, 1999

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By P. Klut, D. Groult, R. Marechalle, B. T. H. Bonnema

In the past 5 years, Compagnie Europeenne de Dezingage (CED) has developed a successful dezincing process and the St. Saulve pilot plant has evolved into a commercially successful production plant. Currently the plant meets all the required standards for scrap and zinc quality, output capacity, availability, and meets the prescribed environmental emissions standards. The initial process problems relating to zinc recovery, uncontrollable explosions and sodium hydroxide aerosol emissions have all been solved. Presntly, the yearly production of dezinced scrap is around 50.000 tonnes/year; this capacity is enough to supply the local market. This capacity can be increased easily to 65.000 tonnes/year or more. The market for dezinced material is growing due to the increased consumption of galvanized material on one hand and on the other hand the higher demand for high quality scrap. The proven technology of CED is currently patented worldwide, but CED is inviting licensees to implement the dezincing technology in other parts of the world.

Jan 1, 2000

By Richard D. Hagni

Reflected light microscopic examination of particles from laboratory experimental copper flash furnaces operated under varied furnace conditions shows that the particles exhibit a wide range in mineral compositions and mineral abundances that correlate with partial pressure of oxygen and concentrate/oxygen ratio. Chalcopyrite, bornite, and digenite are more abundant under low oxygen conditions. With increasing oxygen, metallic copper, delafossite and cuprite become increasingly abundant. The extent of particle agglomeration during flight varies with the furnace. Those products from the larger furnaces exhibit the greater degree of agglomeration. Significant particle fragmentation also is evidenced by cracking and brecciation of some particles.

Jan 1, 1991

By Tetsuro Sakai

Home appliance recycling law was put into force in April 2001 in Japan. Specified kinds of home appliances, such as air conditioners, television sets, refrigerators and washing machines, should be recycled according to the law. Mitsubishi Materials Corporation (MMC) in cooperation with home appliance manufacturers is operating five home appliance recycling plants in Japan. MMC established complete treatment system of recyclable materials generating from home appliance recycling plants, which is formed by unique collaboration among home appliance recycling plants, copper smelter and refinery, and cement plants. Recyclable materials containing copper and precious metals are only handled and treated within the MMC group. By using this lock-in system, safe treatment and traceability of materials are guaranteed as 100% materials recycle.

Jan 1, 2008

By Esa J. Peuraniemi

Copper smelting to form blister in one single step has been possible for a long time even from low grade concentrates. In spite of obvious benefits, it has been economically viable only with few special raw materials having high enough Cu/Fe and Cu/S ratio. Outokumpu Blister Flash Smelting is currently applied at three operations, and three others will be commissioned in the near future. With typical chalcopyrite concentrates two main obstacles have prevented wider adaptation of direct blister processing: slag formation and heat generation. Oxygen potential in the reaction shaft must be high in order to produce blister with targeted sulfur content below 1%. When large amount of iron is oxidized, as well as sulfur, copper is inevitably also oxidized into slag. High copper amount in substantial tonnages of slag lead on to costly down stream recovery operations to obtain discardable slag. Almost complete oxidation of sulfur and iron releases a high amount of heat which traditionally has been solved by lowering oxygen enrichment of the blast leading on to oversized off-gas line and acid plant. One challenge in direct blister smelting relates to the attack of aggressive high-copper containing slag against furnace refractory lining. In continuously operated Outokumpu Direct Blister Flash Smelting this is taken care of by preventing vigorous melt movement in the settler. Stable bath conditions and stationary slag against refractory lining enable the formation of a protective autogenous layer between aggressive slag and vulnerable refractory. These direct blister smelting challenges are addressed from equipment and process development point of view. New solutions to overcome the obstacles are presented and discussed.

Jan 1, 2006

By Gennadiy M. Poletayev, Mikhail D. Starostenkov, Alexandra S. Starostenkova

"The process of the combustion synthesis was modeled by computer simulation using the molecular dynamics method. The set of the critical parameters regulating the velocity of the reaction was found from these computer experiments. It was established that the character of structure-energetical transformations at the combustion synthesis in the systems Ni-Al and TiAl depended on the type of boundaries used for the phases delimitation in the bimetal thin films.IntroductionProducing new materials and products, based on the combustion synthesis (CS), is the objective of scientific investigations as one of the most perspective one for industrial applications. But there are several problems connected with theory and experiment. It allows us to forecast the properties of materials. First of all, the main problems are stipulated by structure-energetical transformations taking place at high velocities of the reaction and at high temperatures. It prevents the analyzing of the transformation mechanisms in materials, taking place at microscopic, atomic levels in details.It is evident, that computer simulation allows to decide some problems and to approach to more exact theoretical presentation of structure-energetical reactions taking place at CS. It is known, that the most typical systems, where CS is observed, are bimetals Ni-Al and Ti-Al. The investigation of interphase boundary stability in the systems of Ni-Al and Ni-Fe was made by the method of molecular dynamics in [1]. The bimetal thin film was presented by the packing of atoms in the plane (111) of FCC lattice. It was found that the discrepancy in the sizes of atoms A and B of bimetal was compensated by the formation of 60° top dislocations, set against interphase boundary in the absence of point defects and free volume. The density of top dislocations was proportional to the factor of size discrepancy of atomic components of the bimetal. Diffusional reconstruction of the interphase boundary and areas, situated near it, was observed only at definite concentration of point defects - vacancies, inculcated in the structure of the bimetal at the definite temperature. The atoms of the bimetal component of less size penetrated in the area of the second component with higher velocity. The clusters of intermetallic germs began to form. It led to the growth of the system temperature and acceleration of the process of the diffusional reconstruction of thin film. The following transformations were found: top dislocations splitted into single ones, which climbed from interphase boundary into the zone of more plastic component; the formation of sub grain structures took place."

Jan 1, 2001

By Richard P. Roberts

This paper will discuss the methods for the cooling of aluminum melting furnace? dross .and their impact on the environment. Also discussed will be a case history of an AROS Dross Processor installation, which is designed to maximize the recovery of metal content of the dross in a manner which is not only environmentally cleaner, but which also prepares the output in such a way as to facilitate downstream processes. Handling of the discharged material will be discussed in regards to the recycling of the preserved metal content and deposition of the unusable-materials.

Jan 1, 1992

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Antonio J. Santana de Araujo, Maria G. Silva Valenzuela

Seeking to replace carbon-black as filler of rubber in the production of vulcanized goods, researchers from University of São Paulo have studied different materials types as minerals, vegetal or wastes agricultural and industry. Results of rubber composites filled with MA1 a waste of mineral treatment provided by Esper Industries are presented. MA1 was characterized through X-ray diffraction; Thermal analysis; Scanning Electronic Microscopy; and others laboratory methods. The composite and shaped masses were evaluated by these methods plus their mechanical properties such as tensile strength, elongation at break and hardness. Exceptional results were obtained in the mechanical properties evaluated, better than those obtained with the traditional carbon-black. Seeing the kind of material used as filler, it can conclude that the environmental benefit is present, as well as economic development, giving credibility to the use of these alternative material in replacement carbon black.

Jan 1, 2015

By A. V. Tarasov, V. M. Paretsky

"The design is based on the thermal processing of the wastes in· the intensively bubbled melt in the Vanyukov furnace at the relatively high temperatures (1350- 1450 °C), In this case: -the secondary wastes are not formed; - the especially toxic substances at the outlet from the furnace are absent. The technology was tested on a large scale (on semicommersial bases). Technical and economical basis show profitability of recovery complex for processing of hard garbage waste (HGW) using this technology: the period of capital, investments refunding for the, recovery, complex construction with process annual capacity of 240 thousands tons of wastes is 1,5-2,5 years,"

Jan 1, 2000

By Jean Igor Margem, Rômulo Loiola, Sergio N. Monteiro, Foluke S. de Assis, Frederico M. Margem

"Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.IntroductionThe engineering application of natural fibers extracted from cellulose-containing vegetables, also recognized as lignocellulosic fibers, is presently considered an environmentally correct alternative to replace more expensive, non recyclable and energy-intensive synthetic fibers [1-3]. In fact, composites reinforced with traditional fibers such as coconut, sisal, jute, hemp, etc ... are already on the market in substitution for common glass fiber automobile components [4-6]. Even less known fibers like curaua from the Amazon region are being industrially used [7]. Economical and environmental reasons sustain a promising future trend for natural fiber composites. In comparison with the less expensive glass fiber among energy-intensive synthetics, lignocellulosic fibers are approximately five times cheaper. For the current situation of our planet, natural fibers are regarded as ""green"" environmentally friendly materials. They are abundant, renewable, biodegradable, and recyclable, above all, neutral with respect to carbon dioxide emission, associated with global warming.Several relatively unknown lignocellulosic fibers such as piassava [8], sponge gourd [9], sugar cane bagasse [10], buriti [11] and ramie [12], with simple and limited applications, or just byproducts, are now being investigated for their potential as composite reinforcement. This could widen the offer of new lignocellulosic fibers for composite reinforcement. The banana fiber, in particular, has a tensile strength around 700 MPa [13], which is comparable to the strongest lignocellulosic fibers used as composite reinforcement.In addition to polyester, the epoxy is another relatively strong polymer used as composite matrix. Therefore, the objective of the present work was to assess the mechanical properties obtained by flexural test, for epoxy composites reinforced with different amounts of banana fibers."

Jan 1, 2013

By Bernhard J. Ralph

In refractory gold ores much of the gold occurs in sub-microscopic form in sulfide minerals, most commonly pyrite and arsenopyrite Bacterial leaching is being developed as a pretreatment for these minerals to aid the liberation of gold and a variety of extracting reagents. This paper reviews the nature of the principal micro-organisms involved, the effects of various physico-chemical factors on the rate and extent of extraction, and likely mechanisms involved.

Jan 1, 1989

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001