Search Documents

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By Xiangwen Wang

Electrochemical measurements associated with the electrowinning of lead metal from concentrated brine (NaCI) - lead chloride (PbCI,) electrolytes at temperatures in the range 328 to 353°K (55 - 80°C) were conducted. The electrodeposition of lead metal onto a lead rotating-disk electrode may be described by the electrodic reaction: {PbCl 4 2 + 2e- = Pb° + 4Cl-} The deposition-overpotential requirements are low (approximately 41mV per decade of current density - Am+), with a corresponding high exchange current (approximately 0.018 A.cm2). The diffusion coefficient of the electroactive PbC142- species in a 3.5 NaCl electrolyte at 353°K was insensitive to the total PbCI, concentration (0.01 to 0.1M), and its value was found to be (1.21*0.1)~10-5 cm2Is with a temperature-sensitivity coefficient (E,/R) of approximately 1.98x103K-1 (328OK(T<353OK).

Jan 1, 1993

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Toshiyuki Kawai

Copper concentrate smelting directly in P-S converters was started at Onahama Smelter in 1983. Thereafter, the tonnage of concentrate smelted through the P-S converters increased, such that by 2002, it equaled the tonnage smelted through the reverberatory furnaces. In 2003, 56% of the total copper concentrates treated at Onahama Smelter were processed directly through the P-S converters. Technical improvements are reviewed and advantages of direct smelting in P-S converters are reported.

Jan 1, 2005

By Melissa L. Trapani

Keywords: Copper, Taphole, Flow Instability. ?Blister spitting? is a flow irregularity where the molten blister copper stream ? or part thereof ? sprays from the taphole exit rather than following a regular flow profile to the collection box. As well as being a general ?housekeeping? issue, the unpredictable nature of the flow is a threat to operator safety. Also, the aggressive flow pattern may contribute to the mechanical wear of the taphole refractory, compromising the integrity of the taphole. This paper brings together a collection of first-hand observations and reports from process personnel, and suggests some theories as to the causes of blister spitting.

Jan 1, 2005

By A. Iván, Patiño C. Francisco, Flores B. Javier, Peréz L. Miguel, Hernandez A. Juan, Trapála P. Norma, Salinas R. Eleazar, Rivera L. Isauro, G. Flores, U. Mizraim

"Tills work is related with the production of tiles using wastes from mining and metallurgical industry of Hidalgo State, as raw material. These wastes present a majority particle size (60 %), minor than 53 m (mesh 270, in Tyler Series) with the following composition; 70.01 % wt. of Si02, 12.82 % wt. of Ah03, 3.80 % wt. of Fe, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 grams per ton of Ag and 0.6 grams per ton of Au. In this work, the partial results and experimental conditions for the preparation of some composites to produce tiles are shown. The composite that offers the best results in productions of tiles was that with 66.67 % wt. of mining waste, 26.67 % wt. of red mud and 6.67 % wt. of black mud.IntroductionTo now, mining activities carried out during more than 457 years in Hidalgo State, Mexico; has lead a great volume of wastes; which can be classified into different types, having among the more common; Acid mining water, solid transport water, elements in radical form, abandoned minerals without processing and processing minerals wastes known as burrows, being these the most abundant in the region counting with an approximated volume of 110 million of tons, presenting a fine particle size that can affect population health during windy epochs [1 -4].Form metallurgical point of view, is well known that a fundamental characterization study it is necessary to know the viability of reusing or recycling of these wastes. According this, these residues can also be considered as raw materials in other economical activities, due its Si, Fe, AI, Ca, Na and P oxides contents, its mineralogy and the distribution of chemical elements in the primary and secondary phases [1,2,5,6]."

Jan 1, 2012

By Vincent Menard

The purpose of the present work is to demonstrate the removal of manganese from a neutral leach zinc-rich solution ([Zn] =150 g/L) at 80°C by oxidative precipitation using a gas mixture of sulphur dioxide (SO2) and oxygen (O2). In order to determine the optimum conditions for manganese removal, several bench-scale semi-batch experiments were performed, where the effects of ORP and gas mixing were investigated. These tests showed that SO2/O2 is a fast and effective oxidant for removing manganese down to ppm level as long as the appropriate ORP is attained/maintained and gas transfer kinetics are optimized.

Jan 1, 2006

By Fiseha Tesfaye, Pekka Taskinen, Daniel Lindberg

Due to increasing complexities of raw materials for base metals production the conventional pyrometallurgical processes are challenged. To make the appropriate modifications, thorough evaluations of the thermal stabilities of phases and phase assemblages which are commonly encountered in these processes are essential. In this work, phase relations and thermal stabilities of equilibrium phases in the Cu-Ni-S system have been reviewed. The calculated phase diagram of Cu-Ni system has been validated. At T < 630 K, in the Ni-rich corner, large scatter in data has been observed and discussed in detail. The other binary systems, Cu-S and Ni-S, have been also critically reviewed together with the ternary Cu-Ni-S system. The reviews were focused on compiling and discussing phase relations and thermal stabilities of the selected systems in the pyrometallurgical processes of Cu and Ni productions.

Jan 1, 2016

By Pengfu Tan

Converter slag chemistry control has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter has been developed to predict the behavior of magnetite in the converter slag. Predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2005

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave reflection loss (RL) of ferric oxide is studied in the temperature range from 297 to approximately 1400 Kat frequencies of 915 and 2450 MHz. It is shown that the maximum microwave absorption with RL of -38.46 and -35.97 dB can be obtained for ferric oxide having thicknesses of 0.03 and 0.01 m at 915 and 2450 MHz, respectively. The maximum absorption peak with RL below -10 dB is in a 250 K temperature range from 723 to 973 Kat 915 MHz, which shifts to the range between 823 and 1073 K at 2450 MHz. This migration is in good agreement with the variation of the dielectric loss tangent of ferric oxide.IntroductionMicrowave irradiation has distinguishing characteristics such as volumetric and selective heating compared with conventional methods, leading to extremely broad applications in materials heating and processing [1-5].The efficiency of microwave heating was found to be dependent on various factors, such as microwave power [6], frequency [7,8], radiation time [8], applicator geometry [8], sample microwave absorption properties and position as well as dimension [9-11 ], etc. Among these parameters, sample dimension plays an important role but is usually neglected by researchers in microwave processing of materials. In fact, although numerous studies have been directed toward the utilization of microwave energy to assist materials heating and processing, few reports were released on the effect of sample dimension [12,13].This is because all aforementioned factors influencing microwave heating generally exert interactive effects to each other during the heating process, making clarification of the effect of sample dimension difficult. Therefore, it is necessary to propose a parameter or concept for quantifying the effect of absorber dimension on microwave heating, increasing heating efficiency."

Jan 1, 2013

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

By Muammer Kaya

The purpose of this review is to raise awareness about e-waste problem in the World. Whether generated at our home or our office, e-waste is most rapidly growing waste problem in the world. Even though there are conventional disposal methods (such as landfill and incineration) for e-waste, these methods have both economic and environmental disadvantages; recycling is a new waste management option which diverts end-of-life (EOL) electrical and electronic equipment (EEE) from landfill and incineration [1, 2]. Successful diversion strategy must be based on economic sustainability, technical feasibility and social support [3]. Recycling infrastructure includes transportation, collection, recovery and resale establishments. The first part of this paper describes the e-waste facts, how big is the e-waste problem and existing recycling programmes and collecting methods in the USA and EU; second part, describes various methods available to recover valuable materials (glass, plastic and metals (Pb, Cu, Al, Steel, Ni, Au, Pd, Cu etc)) in e-waste for a safe and environmental friendly disposal

Jan 1, 2009

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By J. R. Donald

For processing copper, continuous converting has been successfully employed in a variety of locations, but for nickel, there has yet to be a successful commercial implementation of continuous converting technology. At Inco?s Copper Cliff smelter, there are specific requirements for the production of Bessemer matte relating to downstream processing that makes continuous converting for nickel mattes even more challenging. The nickel carbonyl refineries require very low iron levels in the matte, and the sulphur deficiency must be carefully controlled such that the appropriate quantity of PGM-rich metallics are produced from matte separation. The present paper outlines continuous converter technologies that have been implemented in copper, and evaluates their potential for nickel converting. The challenges of producing a Bessemer matte to the required specifications are discussed. The economic and environmental driving forces, and the challenges of justifying a novel technology in place of productive existing equipment, are discussed.

Jan 1, 2005

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

By Luciano R. G. Santos

Keywords: biosorption, cadmium, copper, biomass, spent zeolite. The majority of the industrial activities produce some kind of solid wastes. In this work two industrial residues (spent zeolite and wood sawdust) were chemically modified to increase their heavy metals sorption capacities. Manilkara longifolia (a Brazilian plant known as parajú) sawdust was first treated with NaOH and modified with different citric acid concentrations (0.6-1.2 mol/L) at 120°C, for 90 min. Infrared spectroscopy confirmed the presence of carboxylate groups in the wood structure as result of their mixing. Similarly, spent zeolites were also submitted to a chemical treatment (NaOH) to remove carbon deposited during oil cracking and to recover its sorption capacity. Batch experiments carried out at ambient temperature showed that both materials present sorption capacity for copper and cadmium comparable to weak acid ion exchange resins. A maximum of 78 mg-Cd/g and 59.7 mg-Cu/g as well as 29.9 mg-Cd/g and 14.6 mg-Cu/g were observed for the sawdust and the zeolite, respectively. The results were modeled according to the Freundlich and Langmuir equilibrium isotherms and compared with results of other studies.

Jan 1, 2005

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Holger Cordes

X-ray diffraction has long been used for qualitative and quantitative mineral analysis but Rietveld data analysis is still an under utilized method for mineral exploration and processing applications. In this full-profile approach the structural parameters of each mineral phase, together with experimental parameters, are refined by least-squares methods to minimize the difference between observed and calculated diffraction patterns. The result is a standard-less, quantitative analysis of the mineral abundance in the sample that is more accurate and considerably faster compared to traditional methods. The TOPAS software package combines a user-friendly interface with a unique approach to resolve overlapping peaks. Automated analysis options are also available and significantly reduce analysis time for routine samples. Several examples on a wide range of naturally occurring rock types are shown that illustrate the capabilities and limitations of the method. The examples include several options for the quantification of amorphous constituents like volcanic glasses.

Jan 1, 2006