Search Documents

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By Tong Zhilin

The reasons why the pits were formed on the cathode in the process of Ni electrowinning and the methods how to prevent these pits from forming are described. Some examples are presented. It has 'been proven that P507 and P204 present in the electrolyte can effectively prevent pits from forming on the cathode.

Jan 1, 1993

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Raj P. Singh

Applications of cementation in the recovery of metal ions from process solutions have been known for a long time. Cementation reactions involve electrochemical precipitation of a noble metal from solutions of its salts on a more electropositive metal which, in tum, progressively dissolves. For example, addition of zinc metal powder in a solution containing zinc and cobalt ions would allow for the precipitation (separation) of cobalt according to the following chemical reaction. This paper pertains to the recovery of cobalt from cobalt process solutions via a cementation reaction on aluminum shavings (metal scraps from cans etc). Specifically, we report on the characterization of cobalt process solutions, a by-product obtained from cobalt chemicals, and the kinetics of cobalt, nickel and manganese cementation from process solutions on aluminum shavings.

Jan 1, 2000

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate. The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refming times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using C02 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping, Zhai Dacheng

"Corrosion resistance of RE-Ni-W-P-SiC composite coating and 3 l6L stainless steel in corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations by means of immersion methods and anodic polarization curves obtained by DHZ-1 electrochemical synthetic tester and HDV-7 transistor constant potentiometer. Immersion experiment results show that corrosion rate of RE-Ni-W-P-SiC composite coating as-deposited in HCl solutions increases with the rise of HCl concentrations, on the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing the HCl concentrations the corrosion rates of the coatings as-deposited and after heat treatment in H2SO4 and H3PO4 solutions respectively decrease with the rise.of H2SO4 and H3PO4 concentrations the corrosion rate of the deposit as-deposited in FeC13 solutions decreases with increasing FeC13 concentrations, while the rate of the composite coating after heat treatment increases .with the rise of FeC13 concentrations.In addition, the corrosion rate of 3 l 6L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations increases with rising of concentrations. Furthermore, the corrosion rate of 316L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions respectively is much greater than that of the RE-Ni-W-P-SiC composite coating as-deposited and after heat treatment in the same corrosion media.1. IntroductionAll the materials and their products, when processed, stored and used, it is inevitable that the corrosion, wear, fatigue and crack occur owing to the actions of surroundings. Those early failure and abrasion, through all kinds of departments and profession that corrosion consumes one percent of tens of the steel products of the whole world; and two or four percent of the GDP is lost because of the corrosion."

Jan 1, 2000

By Martin E. Nelson

Several heavy metal separation techniques are currently being developed for soil remediation at various Department of Defense and Department of Energy (DOE) Facilities. The majority of these techniques involve a wet process using water, PH modifiers or other compounds. The United States Naval Academy (USNA) has developed a dry process for heavy metal separation. The process uses air classification technology to concentrate the metal contaminant into a fraction of the soil. The advantages of this dry process are that it creates no contaminated by product and uses commercially available technology. The USNA process is based on using a Gayco-Reliance air classifier. Tests have been conducted with the system at the Naval Academy and the University of Nevada-Reno (UNR). The USNA tests used soil from the Nevada Test Site mixed with bismuth at a concentration of 500-1000 ppm. The UNR tests used soil from four DOE sites mixed with uranium oxides and plutonium at an activity level of 100-700 pCi per gram. Concentration of activities and volume reduction percentages are presented for the various soils and contaminants tested.

Jan 1, 1995

By Wenbo Luo, Kang Liu, Jilai Xue

"Coal fly-ash(CFA) from thermal power plants is rich in Al2O3, which has great potential as an alternative resource for alumina production. In this work, Alz03 contained in the coal fly-ash was extracted using an acid sintering-leaching process. This process was enhanced by aid of power ultrasound during the leaching. The recovery rate of Al2O3 was increased with ultrasound, compared with the similar process without ultrasound under the identical operation conditions. Leaching temperature can be lowered by about 10-l5°C and the processing time reduced by about 50%. The process kinetics were investigated in details for a better understanding of the fundamentals on the effects of power ultrasound. The obtained results demonstrate the potential application in reducing processing energy and increasing production rate.Introduction Coal fly ash is a typical solid waste generated from coal combustion in thermal power station. Vast amount of CF A accumulation lead to serious environmental problems such as air and water pollution, cropland occupation, radioactive contamination, etc. However, CFA is rich in Al2O3 and SiO2 content, so that it has a potential use as recourses for alumina and silica production [1]. Aluminum industry, especially in China, has made a rapid expansion in recent years accompanying with a large amount of bauxite consumption, resulting a urgent demand to develop secondary alumina resources like CF A to maintain a sustainable development of aluminum industry that faces grim challenge [2].Acid leaching is an efficient technology to use in alumina extraction from CF A. Since the particle of CF A is not naturally existed mineral but was formed in molten state at high temperature, the internal Al-O-Si bonds are so strong to separate alumina from the ash particle. Because of this reason, the direct acid leaching [3-6] operated at ambient temperature has low extraction efficiency, approximate 30% to 40%, which is attributed to self inhibition effect from CaS04 generated by reaction between CaO and H2S04 [7-8]. High pressure leaching can efficiently decompose mullite to release A12O 3 content in the fly ash particles, but this requires autoclave material having strong acid corrosion resistance, high temperature (100°C-300°C) and pressure (1.0MPa-2.SMPa) resistance while its operating security is low and its acid consumption is large [9]. Concentrated acid boil process is conducted at near acid boiling point (200 °C - 300 °C) in 4 mouth flask wrapped by electric heating jacket with high mass ratio of acid and ash to achieve high Al203 recovery rate from CFA. Its disadvantages are similar to the high pressure leaching technology except no-pressure, and also the operating solution at nearly boiling point acid may easily spill and splash with additional acid loss and potential safety hazard [10]."

Jan 1, 2014

By Paul S. Korinko, Simona E. Hunyadi Murph

To address a radiological contamination event, a materials and process project was initiated. During the course of this project, processes and materials were developed that successfully captured zinc vapors physically and chemically, respectively. However, the physical traps were placed in an undesirable area and it was determined that the chemically captured zinc reactions was reversible. Consequently, advanced nanomaterials are being developed to capture zinc vapors. The current state of the art of the science and engineering of these materials and their efficacy for zinc capture and retention is discussed in this paper.

Jan 1, 2015

By Lv Guozhi, Ren Xiaodong, Liu Yan, Dou Zhihe

"This paper investigated a new desulfurizer, dolomite and ferrosilicon. Magnesium vapor produced by silicothermic reduction of dolomite and ferrosilicon in an immersion tube of molten iron was injected into the molten iron by carrier gas through the underpunch of the tube and desulfurization reaction occurred. In order to explore the desulfurization process of molten iron by the new desulfurizer, the thermodynamics, and experiments of magnesium vapor production and desulfurization have been studied. Through thermodynamic calculation, the reaction temperature of magnesium vapor production by 75ferrosilicon and light-burned dolomite is 1838K in the standard state and decreased with the decreasing partial pressure of magnesium vapor, PMg· When PMg=25kPa, the reaction happens at 1673K. From experiments of magnesium vapor production, reduction efficiency of Mg vapor is about 60 % in 15 minutes at 1673K. From hot metal experiments, the desulfurization efficiency is 89.35%, and the lowest sulfur concentration after desulfurization is 46ppm.IntroductionPretreatment desulfurization of hot metal has become a necessary step in modem optimizing steelmaking process for its cheap cost, which can not only liberate of blast furnace productivity and reduce the burden of produce steel, but also effectively improve overall economic efficiency of the iron and steel system[l-ZJ_ At present, injection magnesium particle is one of the two main methods of desulphurization in hot metal owing to its strong affinity for sulphur, low amount of slag produced, low iron loss in slag skimming and low equipment investment[3l. However, there are still some insufficiencies on the hot iron pretreatment with magnesium particles at present[4-5l"

Jan 1, 2013

By C. S. Simons

This paper presents a review of the extractive processes used in the production of nickel, with emphasis on developments since the beginning of the Second World War. Attention is given to the factors, many outside the nickel industry itself, which determined the direction of process research and strongly influenced the ultimate commitments to industrialize the resulting developments. An example of such a factor is the sudden surge in demand, far exceeding the then available nickel production capacity, that was caused by the advent of World War II; the result was the first serious consideration ever given to low- grade laterites as a viable source of primary nickel. Other factors discussed include such items as process development in the extraction of other metals - particularly copper; the availability of increasingly sophisticated materials of const- ruction; the advent of the "environmentalist" and related political developments; the massive escalation in the price of energy - particularly oil. The paper concludes with an attempt to forecast the nature of the most effective nickel process of the future, based on extrapolation from the economic and political situation that exists today.

Jan 1, 1988

By Takao Yasugi

The majority of copper in the raw material migrates to the de-copperized dross that forms when the crude lead produced in the blast furnace is treated in the de-copperizing process. The de-copperized dross is treated in the electric furnace producing matte, speiss, and crude lead. The de-copperized dross also contains the silver. Therefore, it is important to improve the rate of silver migration to the crude lead. For this reason, the behavior of silver between the matte, speiss and crude lead phases was examined. At the same time, several tests to improve the percentage of silver migrating to crude lead were conducted.

Jan 1, 2003

Physical and chemical properties of the salt flux phase play a significant role in the recycling of UBC in Aluminum melting processes. Particularly knowledge of several properties such as salt vapor pressure, melting temperature, loss of aluminum, corrosion of refractories are useful for the process control decisions in order to attain a good quality of aluminum produced. A literature review and analysis of several salt flux systems for the selection of a flux for the Aluminum melter (low temperature natural gas bath melting) process were made. Based on these analysis two salt flux systems are recommended for further studies. These are NaCl?KCl?LiF system and NaF?LiF?KCl system with small amounts of other salt additives. Application of these fluxes to Al industrial processes are discussed.

Jan 1, 1996

By Michael Altepeter

Big River Zinc Corporation, located in Sauget, Illinois, operates a neutral leach residue circuit. The residue produced in the circuit is sold to lead smelters for subsequent recovery of valuable metals. A research program was initiated several years ago to find a means of treating the residue at Big River Zinc to recover the valuable metals. The Ausmelt submerged lance reactor was selected as the best alternative for the first step of the process. Pilot scale tests were conducted at Ausmelt&apos;s facilities in Melbourne, Australia. Separations were excellent. 99%+ of the Zn, Pb, Cd, and Ag contained in the residue reported to the oxide fume. 99%+ of the SiO2,, Fe, Mg, and Ca in the residue reported to the slag which passed the EPA TCLP test. Subsequent leaching of the oxide fumes and purification of the leach solutions using conventional procedures produced solUtions suitable for zinc electrowinning and an upgraded lead sulfate cake for sale.

Jan 1, 1992

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

By Maria K. Kojo

The interaction between various slags and a nickel concentrate containing pyrite, pentlandite, and violarite were investigated by submerging concentrate pellets in molten slags. The slags were contained in MgO-A12O3 spinel crucibles. The slag oxidizes the iron sulfides in the concentrate, resulting in a nickel matte. The amount of S02 gas formed during reaction was measured to determine the oxidation reactivity of the slags. The experimental variables included temperature, the ferric/ferrous ratio of slag, and other slag properties such as the FeO/SiO2 ratio and the MgO and NiO contents. The reactivity of the slag depended in a complex manner on its oxidizing power, viscosity, and interfacial tension. The slag composition for the greatest reactivity was determined to be Fe3+/Fe2+ = 0.3, Fe/SiO2 = 1.3, and % MgO = 2. This slag, however, caused substantial foaming. Increasing the MgO content to 10% or replacing it by 5% MgO + 8% NiO eliminated at a slight decrease in reactivity. The implications of the findings from this work in the bath smelting of nickel sulfide concentrates are discussed.

Jan 1, 1995

By J. L. Holman

The Bureau of Mines is investigating recovery of Ni, Co, Cr, and other metals from mixed contaminated supera110y scrap. The scrap is melt-refined and cast into anodes for electrodeposition of recyclable Ni-Co alloy. Melt oxidation using roasted superalloy grinding sludge as oxygen source can divert the Cr to the slag but with excessive Ni-Co loss. Melt oxidation-carburization or direct melt carburization retains -95 pct of the Ni-Co in the anode alloy. With direct carburization, -90 pct or more of the Cr and other refractory metals report to the anode alloy, largely as carbide phases insoluble in electrolysis. Electrorefining data relate parameters such as controlled cathode potential, Fe and Cr impurities, pH, and compartmented cell use, to current efficiency and Ni-Co deposit quality. Recovery of -90 pct of the Ni-Co in the scrap can be achieved. Preliminary experiments to recover Cr, W, and other metals from the anode sludge and other byproducts are discussed. 347

Jan 1, 1987

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015