Search Documents

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By K. P. Black, G. W. Sevick, D. E. Hockley, K. S. Sexsmith, J. T. Chapman

Mineralogical analyses of carbonates in depyritized tailings and pyrite concentrate (from depyritization of the tailings) were completed as part of the tailings characterization for the Crandon Project, a massive sulfide deposit in northeastern Wisconsin. The mineralogical study was designed to determine the proportion of calcium and magnesium carbonates, and therefore the effective buffering capacity of carbonates in the tailings. The depyritized tailings are net acid consuming and will be stored in a surface tailings management area. The pyrite concentrate is net acid generating and will be used as backfill in the underground mine workings. The majority of carbonates in the depyritized tailings were ferroan dolomite containing 10 to 15% iron (by weight) and lesser amounts of siderite and magnesian siderite. The proportion of calcium and magnesium-rich carbonates corresponds to several independent tests of carbonate neutralization potential (CO3-NP) availability. The pyrite concentrate had less CO3-NP, indicating segregation of the carbonates during pyrite flotation. These carbonates reported higher iron contents, consistent with the relatively lower availability of CO3-NP in the pyrite concentrate.

Jan 1, 2002

By T. R. Ellis

Minerals Appraisers/Valuers often find great difficulty or failure in attempting to employ the Sales Comparison Approach to the Market Value Appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income producing property. Common criticisms of the sales comparison approach by minerals appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the Income Approach are usually derived by minerals appraisers, and by review of some conspicuous examples of the much too common misuse or abuse of the income approach in market value minerals appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables (see APPENDIX). The examples are used as the basis for discussion of ways to employ adjustments for operating economics and many other factors, while cautioning about the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

When defining a ?megaproject,? one need only to look at Seattle, WA?s State Route 99 Alaskan Way Viaduct replacement project. This $3.1-billion project is one of the largest of its kind in the world, and includes the use of the world?s largest tunnel boring machine (TBM). However, for as large as the Alaskan Way project is ? especially given the size of the TBM being used ? there are several other megaprojects underway around the world. Each has its own challenges that require innovative design techniques and financing arrangements, as well as variations on established tunneling technologies. So it was that 266 tunneling and underground construction professionals ? owners, contractors and engineers ? convened in Seattle in November for the Cutting Edge Conference on Megaprojects. This was the second joint meeting between the Underground Construction Association of SME and the North American Tunneling Journal. The first joint conference took place in April 2012 in Miami, FL and attracted 238 attendees. A third joint conference, to be held in 2014, is in the planning stage. The key reason Seattle was chosen as the site of the megaprojects conference is the Alaskan Way Viaduct project. Before the conference began, many of the attendees were able to visit the project and get a close look at Bertha, the Hitachi Zosen earth pressure balance TBM that is boring the tunnel. In addition, the conference included an exhibit that attracted 20 industry suppliers, up from 10 the previous year in Miami. The 25 presentations during the two-day conference covered all aspects of the tunneling and underground construction of megaprojects. Topics included the Alaskan Way Viaduct project; considerations for procurement and contracting; political risk, financing and insurance; international megaprojects; risk and risk sharing and project delivery. Each session concluded with panel discussions.

Dec 1, 2013

By S. Kawatra, K. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from fines migration. Agglomeration of the ore can immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it “feels right”. We have developed procedures to quantitatively determine whether a binder gives good performance in an acidic solution, and have identified several binders that will be suitable for copper heap leaching.

Jan 1, 2007

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By James McKelvey, Larry Drolet, Jason Swartz

INTRODUCTION When divers discovered that sections of a tunnel housing the pipeline that conveys wastewater from the Charleston Peninsula to the Plum Island Wastewater Treatment Facility had caved in, the Charleston Commissioners of Public Works(CPW) moved quickly to determine a long term solution for the city’s collection system, immediately focusing on the Ashley River sewer tunnel along the western boundary of the peninsula. Working with the Charleston community, as well as federal, state, and local officials, CPW developed a fast track yet long life design that can be used as a model for underground construction of tunnels in urban areas. The paper that follows summarizes key aspects of the Ashley River sewer tunnel project. HISTORICAL CHARLESTON Charleston, South Carolina is a culturally significant and historic city that was originally settled in 1670. There are over 100 buildings on the National Register of Historic Places within the Charleston area. Additionally, the first shots of the American Civil War were fired at Fort Sumter in the Charleston Harbor in 1861. As one can imagine, tourism generates significant business for the area with over 1.5 million people visiting Charleston each year. No project, especially one that requires digging, is done within the old city on the Charleston peninsula without careful planning. Many precautions are necessary to prevent damage or disruption to the historical properties. The Ashley River sewer tunnel project is exclusively in the old city. A lot of work was done during the design phase to minimize the impact to historical properties. Some of this work included: an archeological study (where pre-digs were monitored at all shaft sites by an archeologist); a building/structure assessment study (where structures near a shaft site were completely surveyed and cataloged); and an environmental study.

Jan 1, 2005

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By Ralph Spickermann

UK Seabed Resources (UKSR) signed a manganese nodule exploration contract with the International Seabed Authority on 8 February 2013 for a 58,000 km2 tract on the eastern edge of the Clarion Clipperton Zone (CCZ). UKSR is a private company based in the United Kingdom and established primarily to develop the commercial potential of the CCZ deposits. This is the first of many anticipated regulatory, market and technical milestones that are requisite for (1) environmentally responsible commercial scale production of nodule derived metals and (2) generation of revenue through their sale in the global commodities market. This presentation will describe the progress made to date in this effort and an industry-based perspective on the tasks and challenges that may lie ahead.

Sep 1, 2014

By B. Das

Hematite floatability from two low grade banded iron ores of India, namely banded hematite quartzite (BHQ) and banded hematite jasper (BHJ) using fatty acids and amine as the collectors is investigated under identical physico-chemical conditions. The results indicated that hematite present in BHQ ore is easy to float using both the collectors, compared to BHJ ore. The difference of flotability between the two banded iron ores is that quartz grains are coarser and well liberated below 100 micron size in case of BHQ compared to BHJ ore. In case of BHJ ore, fine hematite and quartz grains are intimately inter-grown and are dispersed in thick jasper bands leading to liberation problems. Besides that, dusty jasper particles coat over hematite surface in case of BHJ ore during the process of grinding, which hinders specific adsorption of collector on hematite or quartz surfaces. This is substantiated by scanning electron microscopy (SEM). The flotation studies have indicated that it is possible to achieve ~64% Fe with ~67% recovery from a BHQ ore using both anionic and cationic collectors from a feed containing around 38% Fe. In contrast, the hematite recovery in BHJ ore was poor. Differences in the ore characteristics that affect the flotability of hematite present in both the ores are compared. Keywords: Banded hematite quartzite, banded hematite jasper, flotation, oleic acid, dodecylamine, QEMSCAN, Scanning electron microscope

Feb 27, 2013

By F. X. Spachtholz

"Raw materials industry is crucial for national economy. German mining companies are known for their high degree of resource efficiency based on modern technology and know how. K+S is one of the world’s leading suppliers of standard and specialty fertilizers. In the salt business, K+S, with sites in Europe as well as North and South America, is the world’s leading producer. The mine sites of K+S are distributed all over the world producing mainly potash and magnesium salts and rock salt. Focus is on the sustainable use of the natural deposits in order to stay competitive. For this reason a raw material policy, both national and international, is necessary to ensure access to new mineable deposits which are still available in Germany. Further on, knowing market conditions is a must for sustainable development. At least sustainability and resource efficiency in potash and rock salt mining are achieved by constantly developing new technologies as well as optimizing the organization and improving qualification of workers."

Jan 1, 2011

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By R. L. Grayson

Focusing on relationships between severity measure versus productivity and other factors, this paper presents a comprehensive study of injuries for U.S. underground coal mines in 1996 by mine size. Based on analyses of data, generally the larger the mine, the more productive it is (in tons per employee-hour), but the more severe is its injury experience (r = 0.65). Within very large, large, and medium mine sizes, however, the more productive the mine, the less severe is its injury experience (r =-0.43, -0.36, and -0.26, respectively). For small and very small mines, a more deeply nested analysis is required to understand relationships. Other interesting relationships and comparisons are presented.

Jan 1, 2000

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Botelho Junior, Amilton Barbosa, Denise C. R. Espinosa, David B. Dreisinger

Copper and cobalt can be found on nickel laterite ores, and cobalt can be found also on copper ores, and many contaminants such as iron, aluminum, and magnesium are associated with these ores. In hydrometallurgical process, a purification step is necessary after leaching due to the presence of these impurities. Chelating resins are more selective for some metals than others, making them more efficient than cationic resins. This overview discusses chelating resin applications to recover copper, nickel, and cobalt from mining process and mining tailings and the effect of contaminants in leach solution. Chelating resins with iminodiacetate functional group can be used for selective copper recovery, and both iminodiacetate and bis-picolylamine resins are highly selective for nickel and cobalt. Chelating resins with the same functional group can have different performances on the kinetics of loading, because of variations of structure, the density of functional group, and degree of cross-linking. This article reviews commercial chelating resins that can be applied in leach solutions with different compositions, and also possible innovations for uses of chelating resins to recover metals from mining process and mining tailings.