Search Documents

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By Werner Bilfinger, Claudio Nahas, Marcelo Waimberg

"INTRODUCTION The so called Porto Maravilha Project consists of the re-urbanization of a 500 ha area in the Rio de Janeiro port region. Several changes in local infrastructure are being implemented, including a significant change in the road system, with the demolition of the former “Via Perimetral” viaduct and construction of 4 new tunnels: • Saúde tunnel - 35 m long (Waimberg et al, 2014); • “Binária tunnel” - 1012 m long; • “Via Expressa” twin tunnels - 1850 m long each way. The tunnels were excavated almost completely in rock using conventional drill and blast methodology and only some short stretches in weathered rock, associated to faults zones, residual soils and marine sediments close to the tunnel portals. During excavation of access shaft and “Via Expressa” and “Binária” tunnels significant ground settlements as well as settlements of buildings founded both on shallow and deep foundations were measured. These values could not be associated to conventional tunneling induced settlement troughs. This paper focuses on the “Via Expressa” tunnels, presenting a brief description of the project as a whole, its geological and geotechnical background, monitoring results, and a discussion of possible causes of the measured settlements. PROJECT DESCRIPTION The Porto Maravilha Project is an integrated multidisciplinary action on behalf of the Rio de Janeiro city council with support from the State and Federal Governments. In addition to creating new conditions for working, housing, transport, culture and leisure for the resident population, it also promotes expressive economic development in the region (Portonovo, 2015). Porto Maravilha Project is carrying out actions for the recovery of the region’s historical heritage, as well as promoting the population´s social and economic development. One of the main benefits of the Porto Maravilha Project is the construction of the new traffic system in the port area, consisting of the Express and Binário roadways. The new project, which will replace the current Perimetral Rodrigues Alves viaduct system, will increase traffic flow capacity by 27%."

Jan 1, 2016

By Adabala Raja Venkata Sai Naresh, Radhakanta Koner

Particle size distribution (PSD) is an essential parameter in assessing the overall efficiency of blasting operations in mines and the subsequent mine-to-mill process in the mining industry. Despite some drawbacks of 2D image analysis techniques in accurately estimating particle sizes in PSD, the mining industry has relied on them for the last three decades. This study proposes the 3D rock fragmentation measurement (3DFM) technique for deducting the accurate dimensions of 3D rock particles for the PSD. 3DFM has utilized different processing algorithms. Images of different views of the non-touching rock particles of varying sizes have been acquired as a data acquisition step of structure from motion technology for generating sparse point cloud. Dense point cloud reconstruction is used to avail finer details of the point cloud using clustering views for the multi-view stereo algorithm. Random sample consensus (RANSAC) algorithm coupled with an unsupervised classification using the density-based spatial clustering of applications with noise (DBSCAN) classifier is employed to extract the rock clusters from the 3D point cloud. Finally, the accurate rock sizes are derived using the hybrid bounding box rotation identification (HYBBRID) algorithm with a root mean square error (RMSE) of 0.10 cm for length, 0.10 cm for breadth, and 0.32 cm for depth. The PSD of rock fragments obtained from the proposed 3DFM technique is found to be matching with the results of mechanical sieving and manual gauging with an R2 values of 0.98 and 0.99, respectively. The 3DFM method can be considered cheaper, more accurate, and computationally faster in determining the rock dimensions for the PSD determination method to enhance the productivity of the mining industry.

Dec 29, 2023

By I. Martinez-Dominguez

In September 1992, mining in Mexico was opened again to foreign investment by President Salinas-de Gortari, after thirty years of "Mexicanization" of mining industry which limited foreign participation up to a 49 % (or 34 % in case of national reserves) on a Mexican mining corporation. During said period mining in Mexico was controlled by four or five big mining companies and besides mining production was focused mainly on silver, lead, zinc, copper and fluorspar. Suddenly in middle of a big crisis on Mexican mining industry due to low prices of minerals in the world and also in a period on which it seems that mining industry in the United States and Canada has been condemned to die for environmental reasons, it appears a new Mexican Mining Law to permit foreigners to participate in mining in Mexico' trough Mexican mining corporations that they may control up to 100 %

Jan 1, 1994

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By W. J. Kennedy

Energy management in industry has recently achieved notice as a way to reduce costs without decreasing production. The same approach used in industry can be used in mining, even though the processes are different. This approach is based upon a three phase system of data collection, implementation, and monitoring, all aimed at gathering and evaluating information in such a way as to have a maximum impact on energy costs. This approach has these advantages: (1) attention is directed toward the part of each mining system where the most energy is used, (2) input is collected systematically from all persons involved in the operation of each system, and (3) a means of monitoring the progress toward established goals is created. The mining systems considered are truck haulage, conveyor haulage, blasting and crushing, and lighting. After describing the general procedure, the authors have described a specific method for improving the efficiency (and hence the energy consumption) of round-trip truck haul age systems.

Jan 1, 1982

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By T. Gupta, T. Ghosh

"Rare Earth Elements (REEs) and their compounds are essential for numerous modern high tech applications such as renewable energy technologies, catalysts and defense applications. The destabilization of REE pricing owing to the global demand and supply deficit has forced many countries to re-evaluate the possibility of indigenous production of REEs. Cost effective and eco-friendly opportunities are being widely explored for extraction of REEs from non-conventional mineral sources such as coal and coal byproducts to stabilize the supply chain. Coal from Central Alaska (Healy Coal Mine) and Southern Alaska-Cook Inlet (Wishbone Hill) province have been found to possess elevated REE concentrations as compared to average world coal estimates. The objective of the study is to enrich the REEs in the fine size fraction (-75 Microns) from Healy and Wishbone Hill by froth flotation technique. A Box-Behnken design was applied for modeling and optimization of some operating variables on the flotation to maximize REE enrichment. The variables studies were frother dosage, pulp density (% Solids) and collector dosage. Experiments were carried out using a statistical design and the main and interaction effects on response variable was evaluated by analyzing 3D response surfaces. Based on the experimental results the optimum flotation conditions for maximum REE enrichment in the froth fraction was obtained at 4.2% Solids and 32.7 ppm of frother dosage for Healy coal sample and 10% Solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic equation for modelling and optimizing the response variable is found to be independent of collector dosage for both the coal samples. INTRODUCTION Alaskan coal deposits are distributed in three major coal provinces and are in Cretaceous and Tertiary rocks. The climate, vegetation type and sedimentation process has attributed to low sulfur content (averaging 0.3 percent) in Alaskan coals compared to other coal deposits found across the globe. In Central Alaska-Nenana and Southern Alaska-Cook Inlet coal province coal resources are contained in Tertiary rocks while bulk of the Coal resource in North Slope coal province is contained in Cretaceous and Tertiary coal bearing rocks [1]. Coals from Central Alaska- Nenana (Healy) and Southern Alaska-Cook Inlet province (Wishbone Hill) have been found to possess elevated concentrations of critical REEs as compared to the amounts present in world coals (Figure 1). The Wishbone Hill deposit is considered a relatively small deposit, with about 14 million tons of identified reserves, compared to Healy which has over 500 million tons identified [2]. The REE concentrations up to 286 ppm and 524 ppm on ash basis have been reported by Gupta et al. in 2016 with elevated concentrations Ce, La, Y and Nd which are expressed to be of critical importance by US Department of Energy. Accordingly, the two coal samples possess the potential to be used as a REE resource in the near future under favorable socio-economic and geo-political scenarios. [3, 4]"

Jan 1, 2017

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Miguel Reyes, Mathew Girman, Chenming Zhou

Modern smart mining increasingly depends on sophisticated electrical and electronic systems for improved safety and productivity. With more electronic systems being introduced underground, the mining industry faces electromagnetic compatibility (EMC) issues caused by electromagnetic energy emitted by one device adversely impacting the normal function of another. This paper provides an overview of EMC and electromagnetic interference (EMI) research for underground mining, including a review of EMI in other industries applicable to mining, published EMI research pertaining to mining applications, representative EMI incidences, related EMI legislation in mining, and mitigation strategies.

Jan 3, 2022

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By H. E. Hirsch

Propelled by the invention of the transistor at Bell Laboratories, germanium&apos;s unique properties have advanced our electronic world by many years. Germanium has found major uses in infrared optics, fiber optics and a revised vigor as a catalyst for PET plastic production. Other advanced applications are in various stages of development. The solid state electronics industry has been the driving force behind the accelerating demand for gallium since the late sixties. Past developments of substrates for light emitting diodes, lasers and magnetic bubble memories are paling in view of the current excitement over the use of semi-insulating gallium arsenide for high performance integrated circuits. This application requires gallium metal and gallium compounds of extraordinary purity.

Jan 1, 1986

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at NIOSH’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six different water sprays at pressures ranging from 689 kPa (100 psi) to 6,895 kPa (1,000 psi) in a 14.5-m3 (512-ft3) confined dust chamber. Testing was conducted to determine the effect of various pressures on each spray’s respirable coal dust knockdown ability. It is known that higher water pressures are typically preferred for lowering airborne dust concentrations, but it was important to determine at what pressure range the dust knockdown ability of each spray plateaus or reaches its minimum dust concentration. Results from this testing showed that several sprays saw up to 100% decrease in dust concentrations during the five-minute water spray testing period, with some occurring well below the maximum 6,895 kPa (1,000 psi) spray pressure.

Feb 1, 2023

By Shu Fan Chau, Innes Duncan, Harry Asche, Bill Newns

The North Auckland Line (NAL) in Northland, New Zealand, is being upgraded to pass Hi-Cube containers. The line includes many tunnels and bridges which need to be refurbished to improve structural clearances and line capacity. Tunnel 2 along the line, the Makarau Tunnel, has posed special challenges. Opened in 1898, the tunnel suffered multiple collapses during construction and has shown significant distortion during operation. The tunnel has been repaired many times since opening. Successfully enlarging this delicate and distressed structure has involved historical research, advanced analysis and design, and careful construction. The results provide lessons for dealing with brick lined tunnels and poor ground conditions

Jun 13, 2021

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974

By James P. Cooney

What is required for the mining industry to grow and prosper in a politically challenging world? The answer to this can be summarized as “the industry’s three priorities.” The first priority is gaining access to the world’s mineralized jurisdictions. The second is establishing a measure of security and predictability in government treatment of mining. Confidence in the stability of the fiscal and legal framework within which mining operates is necessary to encourage the investment of large amounts of capital in mine development. The third priority is sustaining the industry’s welcome during the long term in those jurisdictions worthy of investment.

Jan 1, 1996

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee&apos;s theme of 1987&apos;s Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950&apos;s, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.