Search Documents

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

Abrasivity and wear resistance are not intrinsic properties of materials, but rather parameters describing the interaction between the wear part and the material exerting the wearing action. Moreover, wear or, at least, that part of the wear which is due to the cumulative effect of minute scratches, is linked to the hardness disparity concept. Abrasivity, in this context, is a relative concept, pertaining to a metal-rock pair, rather than to a rock. Based on this assumption, a methodology has been developed and checked against actual cases, enabling description of the abrasiveness of arock or the abrasion resistance of a metal through the ratio of comparable quantitative indicators. The paper describes the methods and provides examples of applications to practical cases(namely: rock cutting, excavation by means of tunnel boring machines (TBMs), rock crushing, and hydro-mill cutting).

Jan 1, 2012

By P. Kluge

Mining engineers frequently encounter complex design problems for which the critical components of the design are difficult to quantify or compare. Teams of people typically work on these designs and human perceptions and judgments play a strong role. To assist with this process, the analytical hierarchical process (AHP) as a decisionmaking tool is described in this paper. Although the technique is used in many other disciplines, it is currently not widely used in mining engineering in South Africa. To use the AHP process, the problem should be treated as a hierarchy that defines the goal, the alternatives to reach it, and the criteria for evaluation of these alternatives. Pair wise comparisons are conducted on the criteria of the hierarchy to establish priorities. The value of the technique is that it is simple to test for consistency amongst the pair wise comparisons to ensure that the answer obtained is better than that provided by a random selection. To illustrate the technique, the use of a backfill support system in a platinum mining project was investigated. Ten design parameters, which will be impacted by the use of backfill, were identified and weighted according to their relative importance. The result of the AHP evaluation was that the use of a backfill support system should be preferred to a conventional support system at the mine.

Jan 1, 2011

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By L. J. Leach

Quench and tempered Cr-Mo plate steel was found not to contain a fully martensitic structure as a result of either slow slack quenching or insufficient hardenability at the cooling rates used. The resulting microstructure contains bainite in combination with martensite. It is necessary to examine the implications of bainite for the toughness of the final product. Loss of toughness arises primarily from the inter-lath carbides that typically form in upper bainite. An investigation into the effect of upper bainite in a martensitic matrix of a steel grade containing 0.17% C, 0.1% Cr, 0.54% Mo, and 20 ppm Bindicated lower toughness than in a fully martensitic structure.

Jan 1, 2013

By K. S. Liddell, L. A. Smith

"Kell is a hydrometallurgical treatment option for the recovery of platinum group metals (PGMs), gold, silver, and base metals from flotation concentrates to refined products on site. The process is cyanidefree, while eliminating emissions of sulphur dioxide, arsenic trioxide, and other toxic species often emitted by smelters and roasters. Kell has been tested on a range of concentrates, including PGMs (UG2, Merensky, Platreef, Great Dyke, Great Lakes, Lake Superior and others), refractory gold-silver, coppergold, and polymetallic concentrates. High extraction efficiencies (>95%) are achieved for value metals (Pt, Pd, Rh, Au, Ag, Ni, Cu, Co) and secondary metals (Sb, Zn, Pb, and others). Studies comparing Kell with smelter-refining show economic benefits: capex 18–33% of smelting; opex 51–66%; electricity consumption 13–46%; and environmental benefits: greenhouse gas emissions 57–61% of smelting, acidification 5–27%, human toxicity 37–62%, and freshwater ecotoxicity 43–55% of smelting. Synergies for Kell plants alongside smelter-refineries include utilization of recovered acid from sulphur abatement systems and excess capacity in precious metal refineries. Kell is unconstrained by concentrate grade and impurities, allowing the co-location of Kell plants for treatment of non-smeltable concentrates alongside existing smelters.Kell has been demonstrated in a nine-week integrated pilot campaign at 1:1000 scale, supporting a bankable feasibility study for a 110 000 t/a plant treating a UG2-Merensky concentrate at Pilanesberg Platinum Mine (PPM), owned by Sedibelo Platinum Ltd, which has along with South African Industrial Development Corporation (IDC), invested in Kell. Zimbabwean Mining Development Corporation (ZMDC) has signed a Memorandum of Agreement (MOA) with KellTech for a centralized PGM concentrate processing plant."

Jun 1, 2019

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

By I. Ocak

The modulus of elasticity of rock material (Ei) is an important rock property that is used as an input parameter in the design stage of engineering projects such as dam and tunnel constructions, mining excavations, and so forth. However, determination of the modulus of elasticity is sometimes difficult to obtain by laboratory tests because high-quality cores are required. For this reason, empirical methods for predicting the modulus of elasticity of rock material have been popular research topics in recently published literature. In this study, the relationships between the uniaxial compressive strength (UCS), unit weight (?) and modulus of elasticity for different types of rocks were analysed by using 177 data obtained from laboratory tests carried out on cores obtained from drill holes within the area of the Kadiköy-Kartal Metro line (Istanbul, Turkey). Keywords: Kadikoy?Kartal Metro, uniaxial compressive strength, unit weight, estimating the modulus of elasticity.

Jan 1, 2008

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

In order to deliver a quality shotcrete and concrete product underground for the extensions to the Cullinan Diamond Mine operations it was decided to develop a new, simpler concrete product to meet underground support requirements. The aim was to develop a concrete product that not only reduced costs but also met the performance criteria of the current range of concrete products used on Cullinan Diamond Mine, a 25, 45 and 60 MPa concrete and a fibre reinforced wet shotcrete. The concrete product batching and delivery system was to be from surface as opposed to the current underground batching systems. The operational principle was to include an automated surface batching plant with delivery of the concrete product to a borehole containing suspended pipelines delivering to an underground storage facility from where the product is delivered to the working area by further pumping or agicars. Keywords: concrete, shotcrete, full flow, frictional loss, pipeline transport, positive displacment pump

Jan 1, 2006

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By A. More, J. Bullón

Metal casting is one of the most important operations in ferroalloys factories. After the tapping of the furnace and the depuration of the metal, the preparation for customers with cooling, crushing and sizing begins. In total production costs, this contains around 8 % of the total cost of the metal, depending on the value of the fines and other important parameters. From an investment point of view, this represents around 20% of the total capital for a new furnace. Casting onto a water-refrigerated copper plate is not new for molten metals. In steel, continuous casting machines are normal in every factory. Water granulation casting exists at some ferroalloys plants. However, the majority of plants and production technology still use the technology of lumping, crushing and sizing. This technology is time consuming, produces fines and requires a relatively large work force. In 2001, Ferroatlantica put into operation a new water-cooled copper casting-machine, which seems to be a very convenient solution to solve all these problems. It is in operation at a silicon factory; the same place where the new ELSA electrode was developed for silicon metal production. This paper describes our experiences using it.

Jan 1, 2004

[ ]

Jan 1, 2009

By F. Habashi

The first documentary evidence for the use of fire to extract a metal was furnished by the wall paintings of the ancient Egyptians showing workers using the blowpipe and bellows to increase the temperature to melt gold in a crucible. Furnaces grew in size and complexity, coke replaced charcoal in the blast furnace, and the Industrial Revolution took place in England that gradually spread worldwide. More metals became known and new techniques were introduced for their extraction. Among these, metallothermic reactions became prominent in the nineteenth century immediately after the discovery of the electric current and its use to liberate the alkali metals from their salts. Once these metals became available, they were used to produce aluminium from alumina that resisted all other methods of attack. Aluminium, now available on a large scale, was used to decompose the most stable compounds and liberate more metals that became the basis of modern civilization.

Jan 1, 2004

By R. Armstrong

Due to limited available level ground, Nkomati Nickel Mine cut a weathered rock slope at the base of a mountain spur in order to create a platform for construction of the primary crusher plant and run-of-mine stockpiles. As space is limited around the mining area, ore processing at Nkomati is based on a high reliability of flow of material through the crusher plant, with minimal usage of other and larger designed stockpiles. Evidently, any crusher plant shutdown will render the mine as a whole unproductive and put excessive strain on the medium- to long-term large ore stockpiles, the deposition rates for which are restricted by founding material consolidation requirements. At the onset of the 2012 rainy season, movement was identified on the slope monitoring system and cracks developed on the slope. After a minor failure on the crusher slope an assessment of the slope stability was conducted and a slope management plan recommended, which included deployment of real-time monitoring. An evaluation of the conditions leading to instability was conducted and the likely causes for the failure identified. A full evaluation of the slope monitoring, rainfall, and mining conditions was undertaken and movement triggers were determined. This paper describes the events leading to the development of the failure and the evaluation of the monitoring data to determine a management plan for the failure that allowed for minimal shutdowns of the primary crusher.

Jan 1, 2014

By M. du Plessis, D. F. Malan

"The aim of any mine design is to ensure that the excavations remain stable for the period they will be in use. Various pillar systems are used to ensure that underground stopes remain stable and that mining activities do not affect the surface infrastructure through either surface subsidence or seismicity. Intermediate-depth platinum mines make use of in-stope pillars designed to fail while the pillars are being cut at the mining face. The pillar stress exceeds the loading capacity and the pillars crush as a result. The aim of the paper is to provide an overview of in-stope crush pillars. This will include the application, behaviour, function, mechanism, impact, and design of a crush pillar system."

Jan 1, 2015

By D. S. van Vuuren

Over the last 60 years many different processes were conceived to reduce the cost of titanium produced by the Kroll process. However, success eluded all previous efforts, which were consequently terminated in periods of economic downturn. Recently, the grow thin demand for titanium and the high cost of producing the metal again sparked renewed attempts in various parts of the world to replace the antiquated Kroll process with a more efficient route. The different options to produce titanium are reviewed, classified and evaluated in terms of the fundamentals underlying the technologies, and it is shown that the options considered to be the most likely to replace the Kroll process, are continuous processes to reduce TiCl4 metallo-thermically to titanium powder. Of these, continuous magnesio-thermic reduction of TiCl4 would conceptually result in the lowest-cost and highest-value product. However, when considering by-product salt removal from the titanium product and recycling of the salt as well, sodio-thermic reduction of TiCl4 is better.

Jan 1, 2009