Search Documents

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By Norman L. Wimmler

Active placer mining in Alaska began near Juneau in 1880, but the first gold rush did not start until 1896; then the discovery of the Klondike brought gold seekers from all parts of the world. A few of the newcomers were experienced miners, but the majority knew nothing whatever of placer mining. Even those who were placer miners of much experience found entirely new conditions, notably frozen ground, that presented many difficult problems. As a result, numerous methods of mining and of thawing frozen ground were tried. From these trials the practice described in this bulletin has been developed. All known placer fields in Alaska have been mined to some extent, and some have been virtually exhausted. In most districts, however, there remain large quantities of low-grade gravel and also some small isolated areas of comparatively rich gravels which could not be successfully mined because of adverse physical conditions. These districts are now the scene of most placer mining, including dredging, hydraulicking, drifting, mechanical methods of open-cut mining, and ground sluicing (or booming) followed by " shoveling-in."

Jan 1, 1927

By R. Ward Stahl

This publication is a revision of Report of Investigations 5363 updated to reflect the improvement in fire protection at selected coal mines and contains suggestions on what may be considered good fire protective equipment, suggested methods of organizing the attack on fires at various locations underground, and helpful hints on testing and evaluating firefighting facilities.

Jan 1, 1968

By Carl H. Beal

The oil industry in the United States is further advanced than in any other country, because of American initiative and the development of industries dependent in some way on petroleum or its products. For this reason the output has constantly increased (fig. 1), and as a result this country has produced more than half of the total output of the world. Trw total past output of the world is approximately 7,000,000,000 barrels of 42 gallons each; of this the United States produced about 4,000,000,000 barrels, or about 57 per cent. The limit of production in this country is being approached, however, and although new fields undoubtedly await discovery, the yearly outpnt must inevitably decline, because the maintenance of a given output each year necessitates the drilling of an increasing number of wells. Such an increase becomes impossible after a certain point is reached, not only because of a lack of acreage to be drilled, but because of the great number of wells that will ultimately have to be drilled. According to figure 1, the daily production per well each year has increased during the last few years. However, this increase is abnormal, being caused by the new pools brought in. Although such a condition may continue for several years, the average production per well will finally begin to decrease on account of the lack of new pools to make up for the normal decline in production of the old ones.

Jan 1, 1919

By McHenry Mosier

This paper constitutes the third progress report on a national survey of the use of detachable bits in metal mines. It presents comparative costs of drilling with conventional and detachable bits and describes the operating practice in rock drilling and the reconditioning of drill steel and bits at 10 mines not discussed in previous reports.3/ ACKNOWLEDGMENTS This report has been prepared with the assistance and cooperation of the officials and staff members at the mines visited. Costs and other data at individual mines were developed and furnished by the operators.

Jan 1, 1937

By Lincoln A. Stewart

"INTRODUCTION The First Supplemental National Defense Appropriation Act, approved August, 25,, 1941, authorized the Bureau of Mines to investigate sources of raw, material for western production and appropriated funds for that purpose. Numerous iron deposits and prospects in the Western States were investigated. Among those selected for more detailed investigation were tile Apache and Chodiski deposits in Arizona.The United States Geological Survey had examined these deposits in 1929 3/ and estimated that ""the quantity of minable ore reasonably to be expected in this locality will reach 10,000,000 long tons, but it will require prospecting by core drill to demonstrate this quantity with certainty"". C. H. Johnson, a mining engineer of the Bureau of Mines, made a preliminary examination in October 1941 and proposed exploration of the Apache deposit Canyon Creek.A trench sampling project was set up, and work at the Apache deposit commenced in November 1941. Mapping, trenching, and sampling of outcrops was completed in March 1942. Trenches were laid out at approximately 200-foot intervals for about 9,200 feet along the iron outcrop east of Canyon Creek, and channel samples were taken across the iron formation. The outcrop also was explored by trenching and sampling along a 1,900-foot outcrop on the west side of Canyon Creek.The first diamond-drilling campaign at Apache was initiated in May 1942 and continued to January 1943, when work was suspended owing to depletion of funds. Six holes spaced at approximately 500-foot intervals and, 500 feet back from the outcrop on the east side of Canyon Creek were drilled through the iron formation during this period.While this drilling was in progress, the Chediski deposit was mapped, trenched, and sampled. The trenches were spaced at intervals of approximately 800 feet along 10,000 feet of the iron-ore outcrop."

Jul 1, 1947

By Albert L. Toenges

[sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we. sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we.]

Jan 1, 1938

By R. L. Levens

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface area exposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 2010

This Bureau of Mines report reviews the development of the world potash industry. The trends leading to the present market situation of oversupply arid low prices, which threaten; the domestic potash industry, are presented and analyzed. Because the major threat to the domestic industry comes from Canadian imports, the report focuses on the comparative economics of United States and Canadian production. The study resulted in these major conclusions: 1. Balance of world supply and demand is foreseeable in 1975, but it could be delayed by planned expansion. 2. Balance of U.S. supply and demand could occur as early as 1974-75 or as late as 1981. 3. Nearly all U. S. production capacity vis-a-vis Canadian competition is now uneconomic. Prices cover out-of -pocket costs for only 30 percent of U.S. production. 4. U.S. producers will be undersold by Canadians in 60 to 90 percent of the U.S. market. Canadians also will have the edge over United States and European producers in export markets. 5. U.S. firms have invested in 60 percent of the planned 1971 Canadian production, and they have large holdings in Saskatchewan. 6. The decline in the U.S. potash industry probably reduced personal income in Carlsbad, Eddy County, N. Mex, the chief potash-producing area in the United States, about $21.5 million between 1966 and 1969.

Jan 1, 1970

By J. P. Connell

The U.S. Bureau of Mines awarded a contract to Morrison-Knudsen, Inc., to evaluate the use of roadheaders in underground mining operations. Road-headers were found to be widely used in mines as construction support units, as development miners, and as stoping machines. However, road-headers were found to have mechanical and electrical problems, to suffer reduced productivity when integrated into the mining cycle, and to create dust problems. Also high capital costs and low utilization and avail-ability cause high amortization costs per ton. This report identifies the roadheader operating problems and offers suggestions for improved mechanical and electrical design as well as manufacturer and owner responsibilities for improved availability. The development of a complex integrated excavation and ground support sys tern is no t warranted until the roadheader itself is made much more reliable.

Jan 1, 1980

By V. T. Dow

This report describes construction details and methods used in driving the 5490 tunnel at the Kennecott Copper Corp, property, Bingham, Utah. The tunnel will provide railroad access to the world-famous open-pit copper mine at the projected 5490 level. This publication is one of a series prepared by the Bureau of Mines to depict mining operations and techniques in various mining districts in the United States. Utah Construction and Mining Go. (formerly Utah Construction Co.), contractor on the tunnel project, began work during September 1956 and completed the project in February 1959. The tunnel is 18 feet wide, 24 feet high, and about 18,000 feet long, It will accommodate a railroad locomotive on standard- gage track. With the exception of the last 1,700 feet, the tunnel is supported by steel sets embedded in concrete lining. The 1,700-fact segment of the tunnel is supported by timber sets that will eventually be removed as the pit is deepened.

Jan 1, 1962

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress,

Jan 1, 1965

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources:

Jan 1, 1965