Search Documents

By Franklin D. Cooper

The value of nonfuel mineral raw materials produced in the United States in 1978 was $20 billion. In 1979, total value increased to an estimated $24 billion, up 20% from 1978. Of the principal metallic ores produced in 1979, about half showed increased quantitative output and all showed increased value per ton compared with that of 1978. Most nonmetallic commodities showed increases in quantitative output and in average value per ton. Because of its decreasing share of the world market, the domestic mineral industry's concerns were the increasing costs of capital, labor, and energy; withdrawals of public lands from mining; and the increasing cost of environmental regulations that tended to deter or delay investment in the Nation's capacity for producing essential minerals.

Jan 1, 1980

By R. F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Bureau of Mines has developed a general method for preparing solutions from a wide range of metal and mineral samples for chemical analysis. The development of the method from current knowledge of vessel material, pressure dissolution techniques, and the fluoride-boric acid reaction is given. The method uses 7 ml of a mixture of HC1-HNO3-HF acids in a ratio of 3.5:2:1.5 sealed in plastic bottles that act as pressure vessels when heated in a boiling water bath. A final volume of 100 ml is obtained by the addition of 93 ml of a 1. 5-pct H3BO3 solution to the bottles, which are reheated; precipitated fluorides as well as sample residue are dissolved by the fluoride-boric acid reaction. A copper slag and a steelmaking slag treated using this method were analyzed by atomic absorption spectroscopy yielding values for Si, Mg, Ca, AI, Fe, Mn, Na, As, Pb, Sb, and Zn very close to certified values with an average relative standard deviation of 2.13 pct. The low cost, reduction in preparation time, ease and safety of sample handling, conservation of reagents, and ability to dissolve volatile materials without loss make this method superior to traditional wet digestion techniques for many materials, and ideal for use with atomic absorption, and optical emission or X-ray emission spectroscopy.

Jan 1, 1980

By Daryl E. Radcliffe

The Bureau of Mines, as part of an agreement with the Bear Coal Co., Somerset, Col o., evaluated the response of a coal mine roof to time lapse. Time lapse, the interval between exposure and support of the roof, was studied using both instrumentation and statistics. Instrumentation studies were designed to equate displacement and rates of displacement with areas of roof left unsupported from 15 minutes to more than 4 days. A statistical study was completed to compare roof fall occurrence with time lapse intervals encountered during normal room-and-pillar mining. Results from this investigation show time lapse, in the Bear mine, to he insignificant with respect to roof stability after installation of permanent support.

Jan 1, 1980

By Sidney Katell

Continuing the series of cost bibliographies which was initiated with the publication of Information Circular 7516 in October 1949, the present report covers the period from January 1959 through December 1959. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, were obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil. On Oct. 16, 1959 a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers became effective. This agreement provides for the publication of the annual bibliography under the sponsorship of both groups with the work load involved in the preparation divided equally between the two. As a result, the present report partially reflects the efforts of the members of the Association.

Jan 1, 1960

By O. Terichow

A pendulum sclerometer designed by the Bureau of Mines is described. Its method of operation is given, along with the results of tests made on representative mineral samples of Mohs' hardness scale to determine the applicability of the device for research on rock testing. The sclerometer hardness values obtained from the tests indicated that reproducibility and accuracy were good. A quantitative comparison of the pendulum hardness values with microhardness and surface energy values published by other investigators showed good agreement on minerals with Mohs' hardness numbers of 2 to 9.

Jan 1, 1967

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By T. J. Ballard

The Ore Knob mine, in Ashe County, N.C., was one of the largest producers of copper in the eastern states during the 1870's. The ore occurs in a fissure vein, which strikes N. 64° E. and dips nearly vertical. The country rock is granite gneiss. Drilling indicated that the vein structure is approximately 200 feet wide and 1,500 feet long. The vein material shows evidence of replacement of the original gneiss by sulfides. Solution cavities in the vein were noted in some places. The ore minerals and pyrrhotite, chalcopyrite, pyrite, and minor quantities of sphalerite. The gangue contains biotite, magnetite, albite, calcite, and many silicate minerals.

Jan 1, 1948

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

The principal activities of the Bureau of Mines Pittsburgh Mining and Safety Research Center during fiscal year 1971 (July 1, 1970, to June 30, 1971) are reviewed in part 1 of this paper. Part 2 summarizes publications during fiscal year 1971.

Jan 1, 1974

By Philip G. Burkhalter

Total yield and backscattered electron coefficients were measured in this Bureau of Mines study in an microanalyzer as a function of atomic number and of primary crier: ;y in the 15- to 35-kilovolt range. The electron coefficients were obtained indirectly from measurements of the specimen electron current and the primary beam current collected in a Faraday cage and were measured with a precision better than 0.5 percent. Secondary electron emission was suppressed with opposing potential applied to a screen grid surrounding the specimen. The values of the backscattered electron coefficients agreed with published values within 5 percent.

Jan 1, 1965

By John D. Bardill

This report covers the magnetic survey in the Redford-Clayburg area , which was part of a general survey of magnetite deposits in New York started in 1943 . Other areas being surveyed include the Star Lake district , St. Lawrence County; Russia Station district , Clinton County; Brewster district , Putnam County; and the Sterling district , Orange County. Only a relatively small portion of the area was covered by reconnaissance and detailed surveys . Results were promising enough to warrant additional work. Magnetic surveys of this type serve as a basis for selecting areas for diamond drilling by the Bureau of lines .

Jan 1, 1947

By H. R. Beard

The citrate process for sulfur dioxide emission control was developed in pursuit of the Bureau of Mines goal of minimizing the adverse environmental impact of mineral-processing operations. This publication describes the gas analysis procedures used during development of the process. The research required the capability to analyze SO2, H2S, CO, CO2, COS, volatile hydrocarbons, NO, NO2, O2, N2, and H2. The methods described include gas chromatography, electrochemical detection, infrared spectroscopy, and the use of a computer program to predict the product composition in complex reactions. Laboratory and pilot plant applications are discussed.

Jan 1, 1979

By Robert S. Sanford

"INTRODUCTION AND SUMMARYThis paper is one of a series recently undertaken by the Mining Branch, Bureau of Mines, College Park, Md., to describe current practice in hauling ore and waste by truck at various mines.Heavy-duty ore trucks are replacing railroads at many large open-cut mines and even at a few underground mines. Recently a few mines have been equipped with trucks for transporting ore to a central point, from which conveyor belts move the ore out of the mine. This paper deals only with truck haulage methods and costs.The requirements for efficient low-cost truck haulage are good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers.A correct balance must be maintained between the primary crusher capacity, the number of shovels loading ore, and the number of trucks hauling ore.The cost of tires is important. Tire companies are manufacturing better tires. Mining companies are prolonging the life of tires by building better roads and maintaining correct tire pressure.The trend is toward heavier equipment. In 1949 it cost $0.0925 a long ton to haul ore and waste with a 15-ton truck and $0.0743 a long ton with a 22-ton truck.When trucks are properly maintained, hauling costs do not increase with the age of the trucks. During 1948 it cost $0.1118 per long ton to haul with the four oldest 15-ton trucks and $0.1130 per long ton to haul with the four newest 15-ton trucks, two of which were purchased in 1945 and two in 1947.The weighted ayerage cost of hauling a long ton of ore to the crusher and waste to the dump has been reduced from $0.1159 in 1948 to $0.087 in 1949."

Oct 1, 1950

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

By D. E. Emerson, C. G. Kirkland, E. M. Frost

An apparatus has been developed for determining the helium content of gases containing 40 percent or more helium . It utilizes activated coconut charcoal at liquid nitrogen temperatures to adsorb constituents other than helium in the mixture . Series of analyses have been run where the mean deviation was less than 0.05 percent helium . Twenty or more analyses can be made in an 8- hour day .

Jan 1, 1964

By James E. Mauser

This report deals with the investigation of a continuous process for producing pure zirconium. It covers the construction, operation, and maintenance of the semicontinuous reactor. The report covers a study of test variables, such as reactor temperature and reluctant charge weights, and evaluates the results, such as billet metal hardness, residual billet salt content, and suitability of a purified billet as a consumable electrode for arc melting. The purpose of this project was to develop an inexpensive and continuous process for producing pure zirconium. The process developed, termed the semicontinuous reactor process, produced billets of compacted zirconium sponge. The metal was produced by reducing zirconium tetrachloride with sodium and magnesium beneath molten byproduct salt. Hydraulic rams at each end of a vertical reaction tube compacted the sponge and ejected it as a billet. These billets were purified by heat under vacuum to remove entrapped salt. The goal was to utilize the purified billet directly as a consumable electrode for arc melting.

Jan 1, 1961

By J. D. Zetterstrom

This report supplements an earlier publication on lightweight aggregates of North and South Dakota.3/ The purpose of the investigation was (1) to study the expansion characteristics of large samples of Dakota clays and shales in a 12-inch by 15-foot rotary kiln; and (2) to improve the laboratory bloating test as a tool for predicting the suitability of samples for the rotary-kiln process. This was done by comparing results of the laboratory and kiln tests.

Jan 1, 1956

By Michael R. Yenchek

Contacts with energized conductors are a major cause of electrocutions in underground coal mines. Sensitive ground fault interrupters (GFI's) installed on in-mine three-phase ac utilization circuits would probably prevent the majority of these deaths. A sensitive GFI is a protective device that detects and interrupts small deadly ground currents in the milliampere range before those currents can cause ventricular fibrillation in humans. Commercially available three-phase sensitive GFI's have not been specifically designed for application in coal mines. The Bureau of Mines therefore tested three commercial GFI models to determine their worthiness for mine power systems. GFI design and construction, transient immunity, reliability, and time-current characteristics were evaluated in laboratory tests. No commercial device was found suitable for mine use without design modifications. The tests results will serve as a basis for the development of a mineworthy sensitive GFI in ongoing Bureau research.

Jan 1, 1985

By C. A. Komar

Renewed interest in the underground gasification of coal evolves from comprehensive studies of earth fracture systems that indicate that the movement of fluids can be controlled in the coalbed. In particular, directional property studies of natural microfissure occurrence, permeability, ultrasonic velocity, tensile strength, and orientation of intervals of inherent rock weakness, together with geologic structure setting and fracture trace analysis, can predict the gaseous flow paths in the coalbed. Having this information, the dominant direction in which gases generated and/or liberated by heat would move can be determined so that appropriate well patterns can be developed. Together with advances made in drilling technology that permit long horizontal holes to be drilled through the coal seams, tests can be conducted to determine whether directional control will permit devolatilization of the coalbed and gasification of the remaining hot coke in a systematic manner to produce a low-Btu gas suited for the generation of electricity.

Jan 1, 1973

By D. A. Wilson

Several promising systems for selectively oxidizing the iron in an iron-tin alloy commonly called "hardhead" were investigated in a research project conducted to devise a method for recovering tin from this troublesome alloy. A satisfactory oxidation method was developed and tested successfully on melts of 2,000 grams. Molten hardhead (near 1,080° C.) was blown with air to oxidize iron and leave tin in the reduced state. Recovery of available tin was 96 to 98 percent. Tin products contained 2 to 0.1 percent iron which was reduced to 0.06 percent by filtration at 250° C. Iron oxide formed during oxidation was absorbed by a fluid flux cover composed of 43 percent silica, 17 percent burned limestone, and 40 percent fused borax. Less successful but nevertheless promising results were obtained with mixtures of steam and hydrogen which were sufficiently selective at temperatures between 600° and 950° C. but did not result in complete oxidation of iron. Carbon dioxide-carbon monoxide mixtures also oxidized iron selectively but incompletely. Both stern and carbon dioxide systems produced sufficiently encouraging results to additional research on these systems.

Jan 1, 1961