Search Documents

By John J. Ridgeway

Habits take us where we were yesterday and attitudes tend to keep us there. Until recently, little had been accomplished to improve conventional explosive energy for use offshore. But with the special requirements of the Offshore Oil Industry, and particularly in the North Sea, most equipment, products and services must be specialized as well. Previous attempts to excavate a trench for a sealine in surf areas had been impossible to accomplish. But with the application of safe, controlled explosive energy, an impossible task to accomplish yesterday has now become a reality. Explosive energy, often overlooked as a convenient and economical offshore tool, excavated a clean trench underwater for a 40" sealine at Djeno in the African Congo recently.

Jan 1, 1977

By Don Larson, Gordon Coleman

The United States Department of Energy, through its contractor Lawrence Livermore National Laboratory, has entered into a contract with Alpha-IRECO, Inc. for the emplacement of approximately 2.9 million pounds of a 50% RX-MD emulsion 50% ANFO blend into an underground chamber for initiation to produce the 12 trillion caloric equivalent of 1,000 metric tons of TNT. The detonation will be closely monitored to determine the characteristics of a large chemical explosion for comparison with data collected from previous like-sized nuclear events in the same location. This data will be shared with former Soviet block countries to facilitate enforcement of the various non-proliferation treaties currently being negotiated between the countries.

Jan 1, 1994

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By T Davids, O J. Jordaan, M D. J Bonneau

As in most other parts of the world, the surface coal mining industry in South Africa is introducing emulsion explosives as the primary bulk blasting agent for use in wet borehole conditions where AN/FO cannot be used. Most of the emulsion products presently in use are gassed to provide sensitivity. The intimate mix between the fuel and oxidizer in the emulsion has been shown to produce a highly efficient explosive. However, a major difference between emulsion and the previous slurry products is its relatively low physical strength. This prompted Rand Mines' Duvha Opencast Mine, a major South African Escom power colliery, to conduct test work to illustrate the effect of emulsion physical consistency on blasthole loading. This paper presents the results of test work conducted at Duvha to investigate the problems associated with loading both AN/FO and emulsion in water filled holes, stemming emulsion holes, and in particular, to illustrate the difficulty in correctly introducing a stemming deck into the emulsion column. Time dependent behavior of the loaded emulsion holes is investigated. Velocity of detonation measurements for freshly manufactured emulsion, and for emulsion after loading through water with sleep times of up to 10 days, are presented.

Jan 1, 1987

By Greg Mclellan, Mark Johnson, John Pepper

Several large quarrying projects recently occurred in Miramar, Florida. These were closely monitored by the Seismologist of Record and Broward County in accordance with County and City regulations. In addition to this monitoring, the City of Miramar employed The Pepper Engineering Group, Inc., to provide additional spot check monitoring and to review the records of the other two parties on a routine basis. Broward County ordinances require that the location of each shot and the nearest protected structure be recorded along with seismograph measurement of each shot at the nearest protected structure. The positions of the blasts and nearest protected structures were determined using GPS. The blast vibrations were measured by seismograph. Over 600 shots, which are the subject of this study, were measured both by the County, the Seismologist and, on many occasions, The Pepper Engineering Group. As such, the vibration data was constantly cross-checked for consistency. The blasting contractor also provided blast designs for each shot. In this paper, the measured vibrations are plotted in terms of Resultant Peak Particle Velocity (RPPV) versus Scaled Distance (SD) on logarithmic scales. The data curves are fitted with least squares and upper 95% and 99% prediction limits are provided. Equations are presented to predict the RPPV based on scaled distance and prediction level using power fits. Statistical information concerning the derivation of the various limits is presented. The raw data used to develop this paper, along with other information concerning the shots, will be posted on the Internet for use by other researchers.

Jan 1, 2000

By Richard J. Mainiero, Eric S. Weiss

This project investigates the behavior of blast waves from the detonation of high explosives in an underground mine. A series of explosive tests was conducted in the underground and surface facilities at the Bureau of Mines' Lake Lynn Laboratory to evaluate the potentially dangerous effects of blast waves produced by open shooting, blown out holes, or accidental detonations of explosives. Shots of C4 and TNT were fired at the dead end of a 6 ft high by 20ft wide entry, at the intersection of two entries, and on the surface. C4 and TNT were chosen for this research because they exhibit very consistent performance. Behavior of the blast wave was evaluated through recording of the pressure as a function of distance from the explosive detonation.

Jan 1, 1995

By Richard A. Dick

Few topics in the blasting industry are more controversial than the proper riming procedure for large-diameter ammonium nitrate-fuel oil (AN-FO) charges, despite the considerable amount of research that has been done both in the laboratory and in the field. The January, April, and June 1975 issues of Emphasis on Blasting contain interesting discussions on priming (5). An ideal primer is one that will surely and efficiently initiate the AN-FO column at the correct location to assure optimum blasting performance. During the 20 years of AN-FO's existence, singlepoint priming, axial priming, multiple-point priming, thermal priming, and shock riming have all been advocated as the "optimum" method. This is not surprising because blasting specialists have often differed on even the most fundamental concepts. To define the optimum primer, we must know what detonation characteristics in the AN-FO column are most desirable. Again, authorities disagree. This paper will discuss conclusions of various studies in an attempt to clear up some of the confusion.

Jan 1, 1976

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Michael Wieland

Smoke/fume measurements from rapid transitory charge reactions are not wholly comparable with thermodynamic reaction code (TDRC) results, since quenched chemical reactions yield nonequilibrium concentrations. Though the work output and major reaction products are usually rendered with minor deviations, the toxic fumes and other minor concentrations reveal some major discrepancies. Work output for charge formulations in underwater or fixture tests were theoretically resolved with work-principal models that form a rough thermodynamic trajectory. Stalled nonequilibrium concentrations are rationalized by finding the underlying quenched reaction(s). The wide relevance of the Zeldovich radical-chain mechanism that transforms nitrogen oxide was previously recognized. The work-principal model (WPM) represents reaction quenching with off-trajectory constraints to render the fumes, without noticeably readjusting the work process. When restraints that characterize the confinement are WPM tractable, the resolution of critical reaction mechanisms is worthwhile, since they remain useful, regardless of the rich, neutral or lean stoichiometry of the charge formulation.

Jan 1, 2012

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By F. Malek

An extensive blast monitoring program has been carried out to study explosive performance and the effectiveness of blast designs in production blasts in a deep underground mine. Comprehensive monitoring of blasting vibrations through multi-station high-capacity high-frequency accelerometers, and borehole deformation history have been the main tools of such analysis. The mining activity involves relatively unstressed stopes as well as highly stressed stopes. More than 30 production blasts have been monitored, and the respective vibrations from close-range as well as distant seismic stations have been analyzed, and the vibration parameters (amplitude and frequency) have been correlated with explosive charge weight in the holes. It is found that the correlation between blasting rounds and the corresponding vibration amplitudes often have poor correlation for a very significant portion of the blasts. These point to either explosive charge malfunction in those specific blast holes, or inadequate blast design, or the effect of high in-situ stresses, or any combination thereof. This paper analyzes these variables and their effect on the overall blasting operation at the mine.

Jan 1, 2013

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By D K. Joyce, B Mohanty

"A variety of initiation modes are currently in use. This includes initiation by single ormultiple detonators and boosters, by detonating cords of varying strengths, and bycombinations of cords and boosters. A lack of clear understanding of the role of initiationon detonation characteristics often leads to under-utilization of the explosives system inblasting. This paper reviews the current practice of initiation in packaged and bulkexplosive products. It illustrates the effect of various types of initiation on energy releasecharacteristics in emulsion and ANFO, through calibrated underwater energy tests. Itcompares energy release under end-inidadon against side-inidadon condition for variousinitiator strengths. The effect of confinement on these characteristics has also beeninvestigated. It is shown that side-initiadon by detonating cord results, in most cases, insignificant degradation of detonation properties. This study also provides guidelines forselecting the optimum mode of initiation for various blasting situations."

Jan 1, 1993

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Robert Hopler

Complying with our request in the February issue of the AGRICULTURAL BLASTER for items that would be of interest to other blasters, Mr. Thomas H. Benton of Tennessee sends us an article in which his methods of securing contracts are explained:

Jan 1, 2013

By Larry R. Fletcher

The Bureau of Mines obtained blasting accident data from the Mine Safety ant Health Administration (MSHA), U. S. Department of Labor. These data were analyzed to determine the most frequent causes of accidents in mine blasting. Accident totals for 1971 through 1981 are tabulated for metal-nonmetal and coal mines both surface and underground. In the past 11 years (1971-1981, inclusive) there has been an annual average of 9 fatal and 121 nonfatal blasting accident victims. Underground mining averaged 6 fatal and 93 nonfatal injuries each year.

Jan 1, 1983

Bloomfield Collieries Rix’s Creek Mine is an open cut coal operation located in the Hunter Valley region of Australia. The mine produces approximately 1.1 mt of saleable product per year and routinely employs cast-blasting practices for its unique dragline-truck overburden excavation method.

Jan 1, 2006

By R Holmberg, C Sjoberg, B Larsson

This paper describes the excavation of an underground naphta storage facility at Stenungsund in Sweden. The main purpose with this paper is to give an overall view of how the excavation was carried out and in what type of bedrock the storage was built. Emphasis has been done to highlight the importance of using cautious blasting to avoid blast damage in the remaining rock. Attempts has also been done in order to evaluate what the degree of Swedish cautious blasting has meant for the rock support costs during the construction period.

Jan 1, 1984

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016