Search Documents

By Leena Korkiala-Tanttu, Noora Lindroos, Juha Forsman

"Construction works at the Helsinki city sea shoreline requires dredging and handling of contaminated sediments. Most of these soft dredged sediments are regarded as too poor quality material for earth construction purposes. Mass stabilization technology has been applied to improve the technical and environmental properties of the dredged sediment in order to utilize the material in construction. The treatment site presented in this article is placed in the West Harbor where the dredged sediments are disposed in basins, mixed with binders by mass stabilization and transported to utilization sites. The volume of these basins is about 90 000 m3. So far these basins have been used three times during the years 2011-2014. The most applied binder has been cement. Its high price and carbon footprint have encouraged use alternative binders. Other used binder materials include fly ash and end product of desulphurization from coal combustion, and fly ash from combustion of Estonian oil shale. The technical and environmental properties of stabilized sediments have been studies in the laboratory and in situ thoroughly. Some properties of the stabilized sediments which have been studied are: compression strength, modulus, hydraulic conductivity, leaching of contaminants, etc. The leaching test results show that heavy metal leaching is very low with all binder materials tested.1. INTRODUCTIONContaminated marine sedimentsMarine sediments in the coastal areas are often contaminated as a consequence of industrial and port activities, as well as the influence of cities located there. Construction activities and reclamation of shore line require dredging and handling of contaminated sediments since the level of contamination inhibit dumping of dredged sediments into the sea. Based on their technical properties, most of these dredged soft and watery sediments (clay, gyttja, etc.) are regarded as too poor quality material for earth construction purposes. Economic, sustainable and environmentally safe management of contaminated, dredged sediments is a key issue in many construction sites.In the City of Helsinki, mass stabilization technology has been applied to improve the technical properties of the dredged sediments in order to utilize the material in construction. Owing to stabilization / deep mixing / solidification, also the contamination is encapsulated in a monolithic solid of a high structural integrity. Thus, contaminants migration is restricted by the decreased surface area exposed to leaching.The treatment site presented in this article is placed in the West Harbor (a place of Helsinki called Jätkäsaari) where dredged sediments are disposed into stabilization basins, mixed with binders by mass stabilization and then transported to final utilization sites. The location and principle of these basins is presented in Figures 1-4. The overall volume of these four stabilization basins is about 90 000 m3."

Jan 1, 2015

By Henry H. Tayler, Eric Sturel

1 Triton Square was originally a six-storey building with a one-level basement located within a commercial development near Euston, London. It was designed and constructed in the 1990s and the foundation scheme comprised straight shafted London Clay piles arranged singly beneath columns. The scheme added three storeys and a five-storey infill in the central atrium area to increase the building floorplate by 70% and maintained the usability of the basement space. As the loads to support the additional floorplate area were greater than the capacity of the existing foundations, an optimised strengthening scheme of small diameter piles installed within the existing basement and a slender retro-fitted raft was installed to augment the existing piles. The re-use and strengthening of almost all of the existing foundations enabled re-use of a very high proportion of the superstructure and in approximately 35,000 tonnes of concrete and 1,900 tonnes of reinforcement and structural steelwork being re-used. The structural embodied carbon for the refurbished building scheme is estimated at an average of 136 kgCO2e/m2, achieving a Structural Carbon Rating Scheme (SCORS) “A” rating with components detailed in the paper.

May 1, 2022

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By Selvaganesh Selvaraju, Deepak Raj, Sandun N. Wimalasena

One of the world leading oil majors is carrying out a multi-billion-dollar expansion of its integrated manufacturing complex in Jurong Island, Singapore, the global oil trading and refining hub. Soil conditions at the site comprise 10-20m thick reclaimed sand, below which is 3-5m of soft marine clay underlain by stiff soils of the Jurong Formation. The conventional foundation solution would adopt driven precast concrete spun piles; however, precast spun piles have a high embodied carbon from the usage of steel and cement. In order to reduce the carbon footprint, an alternative solution comprising deep vibro techniques was developed. The EFFC-DFI carbon calculator was used to demonstrate the expected scope 1, 2 and 3 carbon emissions for both driven pile and vibro techniques. By using in-house, state-of-the-art fuel-efficient machines, alongside the innovative design concept and usage of natural materials such as sand and stones, actual CO2e emissions were reduced from a potential 21,000 tonnes, with the spun pile’s solution, to only 1,900 tonnes. The saved 20,100 tCO2e is equivalent to an average car driving 2,000x around the Earth’s equator. The paper discusses the application of soil improvement as a more sustainable, lower carbon alternative to conventional piled solutions.

May 1, 2022

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over the navigation channel. The subsurface soil profile was quite variable along the bridge alignment. In Virginia, there was fill over soft Alluvial deposits underlain by dense Terrace deposits, as well as remnant foundations from a former ship yard. At the bascule span, there was up to 50 ft of a soft organic silty clay layer underlain by a deep deposit of stiff Cretaceous clay. Along the Maryland approach, there were Alluvial deposits over dense Terrace deposits over stiff Cretaceous clays and dense Cretaceous sands. The variation in subsurface conditions led to the selection of alternative deep foundations that suited the specific conditions and were based on the design phase testing program, from which ultimate design capacities were determined. During construction, there were instances of unexpected pile performance, notably different than that experienced during the design phase testing, requiring changes to the contract installation criteria and re-design. This paper will present the types of deep foundations used for the project, the performance criteria assumed during the design, the measured performance and difficulties encountered during construction, and the resulting remedial actions, i.e., changes to contract installation criteria and/or re-design due to the unanticipated field conditions.

Jan 1, 2009

By Anahita Modiriasari, Benjamin S. Rivers

Measurement while drilling (MWD) is a subsurface exploration technique associated with real-time and continuous monitoring and recording of drilling data during the drilling process. This technique can be used for underground investigations to differentiate ground strata, detect the presence of fractures and voids, and evaluate geological features and mechanical properties of geomaterial. When MWD is used for geotechnical investigations, it can improve site characterization, identify variable conditions, improve design and construction, lead to shorter project delivery times, reduce the cost and risks associated with limited subsurface data and geotechnical uncertainties, and maximum return-on-investment. Given these benefits, MWD is gaining attention among transportation agencies and the geotechnical industry. Federal Highway Administration’s (FHWA’s) innovation deployment program “Every Day Counts (EDC-5)” includes the implementation of Advanced Geotechnical Methods in Exploration (A-GaME), which aims to implement effective, underutilized subsurface exploration methods, including MWD, in U.S. practice. This paper provides an overview of the MWD technology for geotechnical site investigations and presents a case history where MWD was employed to design deep foundation for the construction of a building in Massachusetts. The advantages of this technology for risk reduction and project cost and time saving are also discussed.

Oct 1, 2022

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Shawna Munn, Sarah Speir

Cedarvale Station is one of 25 new Eglinton Crosstown light rail transit (ECLRT) stations along Eglinton Avenue in Toronto. It is an interchange station with the existing Toronto Transit Com- mission (TTC) University subway line and is located at the intersection of two major thoroughfares. The new LRT tunnels run below the existing Yonge Spadina subway line and required total excavation depths of 20 m (65 ft) to facili- tate construction of the new station.

Jan 1, 2023

By Yuji Yamashita, Kazuyoshi Kamimura, Tsuyoshi Takahashi, Naoya Matayoshi

"The CDM-LODIC method (cement deep mixing - low displacement and control) method enables ground displacement to be reduced by removing an amount of soil equivalent to that of injected cement slurry and the volume of the plunged mixing tool, which causes a certain degree of ground displacement. Since the CDM-LODIC method was developed in 1985, it has been applied to over 930 sites and the accumulated volume of stabilized soil has now reached 7.6 million cubic meters.In the CDM method, the number of blade rotations per unit depth in the ground when the mixing blades are withdrawn is considered a construction item. The blade rotation number depends on the degree of mixing between the cement slurry and the ground Some field tests were performed based on the degree of mixing between the cement slurry and the ground. In these tests, a new concept of evaluating the blade rotation number when the screw rod penetrates to a given depth without injecting cement slurry has contributed to the degree of mixing. Furthermore, a correlation exists between the coefficient of efficiency of soil removal and the cement slurry admixture rate. In this paper, we discus the data collected in those field tests and present some application examples.OUTLINE OF CDM-LODIC METHODThe injection of cement slurry may cause some ground displacement during Cement Deep Mixing (CDM). In recent years, due to an increased demand for ground improvement work in urban areas, there is increased concern that buildings near any CDM site may be adversely affected. The deep mixing method which reduces displacement due to mixing (CDM-LODIC method) enables ground displacement to be minimized by removing an amount of soil equivalent to the injected cement slurry and the volume of the mixing tool, which itself causes some ground displacement. When the construction site is near other structures, regardless of whether on or under the ground, the CDM-LODIC method can be used in order to minimize any ground displacement. There are considered to be two main causes of ground displacement as shown in Figure 1. Displacement A indicates ground displacement caused by the volume of the inserted mixing tool during the penetration stage and displacement B indicates ground displacement caused by the volume of the injected stabilizing agent. Thus, by removing soil equivalent to the volume of the inserted mixing tool and the injected stabilizing agent, ground displacement can theoretically be minimized. Figure 2 shows the amount of observed ground displacement in the cases of CDM and CDM-LODIC at an actual site. These case studies indicate that ground displacement can be reduced by removing the soil."

Jan 1, 2015

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Yazen Khasawneh, Yao Zhang

Upgrading and maintenance programs were proposed at a power generating plant in Indiana. To perform construction activities associated with the proposed upgrading and maintenance, a LR11350 crawler crane with a dead load of 1,500 ton was required in the vicinity of existing plant structures. The contact pressure from the crane tracks for the heaviest lift, maximum reach and angle (worst loading condition) were estimated by the rigging engineer to be on the order of 84 psi. Several concerns were raised regarding the total and differential settlements while the crane is in operation and the induced stresses on existing underground utilities due to crane loads. Three-dimensional finite element simulations were conducted using hardening soil model for the subsurface soils and elastic model for the other structural elements (underground utilities and crane mats) to optimize the configuration of the proposed crane foundation. It was found 1-foot thick engineered steel mats underlain by a 1.5-foot thick crushed stone pad will provide enough support to the crane. It will also control the settlement to the allowable limit and maintain the stresses in the underground utilities within tolerance. INTRODUCTION A LR11350 heavy lift crawler crane was proposed as part of an upgrade program at an existing power plant in the state of Indiana. The proposed crane will be sitting on an open ground in the vicinity of existing plant facilities, with multiple underground utilities going beneath the proposed footprint of the new crane pad. The existing utilities are of diverse kinds, including sanitary sewer corrugated metal pipes, electrical conduits and variable steel water/oil drain pipes. The safety and functionality of these underground utilities are critical to maintain the proper operation of the power plant. Therefore, the design of the new crane pad foundation system is of essential to control the ground settlement and the imposed stresses to the existing utilities (Davie et al., 1998, Scott 2017). To ensure all utility locations and depths are identified, the proposed footprint was thoroughly surveyed. Information in regard to each identified utility was provided by the owner. Subsurface explorations were conducted using geotechnical soil borings and soundings to evaluate the ground conditions and generate soil profiles. Numerical simulation and analysis utilizing finite element method were performed to design the crane pad foundation system and evaluate the responses of the utilities. This paper summarizes project information, geotechnical conditions and then focuses on the finite element analysis in assisting the design of crane pad and the utilities evaluation.

Jan 1, 2019

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By Leena Korkiala-Tanttu, Ilkka Vähäaho, Juha Forsman, Paavo Lahdenperä, Kalle Rantala, Osmo Korhonen

"District of Arabianranta (Helsinki, Finland) has been founded on an old seabed, which was filled with miscellaneous soil materials. The subsoil consists of very low shear strength clays and organic clays (gyttjas). The soil was moving towards the sea at a rate of 1050 mm/year, because of filling on top of the soft subsoil. In the middle of 1990’s it was decided to build a residential area to Arabianranta, because it is located only 5 km away from the downtown. To inhibit the movement of soil, it was planned to build this 700 m long deep mixed column-wall barrier along the shore of Arabianranta in the years 1997–2005. A lot of instrumentation and inclinometers were analyzed and it was noticed that the column-wall remains at its place and the displacement rate inside the wall has been only 0.44.6 mm/year after construction works. Nevertheless, the displacement of soil at the landward side of the column-wall is still 1.25.1 mm/year. The soil at the seaside of the barrier is also moving towards the sea 12.922.2 mm/year. Another problem might be displacements of soil near the places where the column-wall ends (tails).1. INTRODUCTIONArabianranta district (Helsinki, Finland) has been an industrial, storage and wasteland area for a long time. Developing this area into a residential area was earlier considered too expensive, so it has been constructed during last decade. The organic clay layers (gyttjas), which have weak shear strength and high water content, were covered by various layers of fillings done in different phases. Because of the fillings, the area was not only consolidating, but also moving horizontally 1050 mm/year towards the sea due to the fact that the frictional soil under clay layers slopes towards the sea. A trial deep mixed structure was constructed in 1997 to inhibit the horizontal displacements of soil. The actual construction of the columnwall was completed in 2000-2005 with overlapping deep mixed cement columns on the seaward boundary. The barrier was built so that the horizontal movements would not risk the pile foundations at Arabianranta. The length of the barrier is about 680 m and width varies between 1220 m. There is a great amount of instrumentation near the barrier (inclinometer casings and other measuring devices). All this measuring information has been collected and analysed at 2014 to find out how this deep mixed column-wall has affected the horizontal displacements."

Jan 1, 2015

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Ramin Motamed, Farshid Ghazavi, Joseph A. W. Toth

"Post-disaster reconnaissance of areas affected by earthquakes has documented extensive damage to buildings with shallow foundations located in liquefaction-prone areas. Currently, estimation of liquefaction settlement is based on empirical correlations that evaluate settlement in the free-field environment and are based on one-dimensional consolidation. However, observations have shown that liquefaction settlement under buildings can be considerably greater. This research is based on a series of 1- g shake table experiments using a transparent soil box to reproduce liquefaction-induced building settlement. Building settlements were evaluated using a scaled model of a building foundation representing a 1-2 story building. Comprehensive parametric study was carried out to establish the effects of several parameters on free-field and building settlements such as building width and thickness of liquefiable soil layer. The experiments utilized accelerometers and pore-water pressure sensors to monitor ground accelerations and buildup of pore-water pressures in both the free-field and model building footprint. Results of these experiments are compared to available centrifuge tests and field observations and conclusions are drawn with respect to the potential scaling effects. Lastly, this paper discusses the feasibility of installing helical piles as a mitigation strategy to reduce the building settlements by presenting some of the exploratory experimental data obtained from this series of 1-g shake table tests.INTRODUCTIONThe 2010-2011 Canterbury earthquake sequence and the 2011 Great Tohoku earthquake are some of the most recent examples where large numbers of low-story structures sustained damage resulting from liquefaction-induced settlements. This damage has commonly been observed in residential and commercial areas developed over loose, unconsolidated and saturated coarse grained soils resulting from both natural and man-made deposits. Damages incurred from the 2010-2011 Canterbury earthquake sequence occurred in the largely unconsolidated fluvial environment bordering the Avon River in Christchurch (Henderson 2013). Similar damage was also incurred during the 2011 Great Tohoku earthquake where liquefaction of soils occurred in both young alluvial deposits and fill materials (Ashford et al. 2011). Figure 1 presents typical modes of failure to structures resulting from the effects of liquefaction. Current practices in evaluation of liquefaction settlement rely on empirical correlations (Tokimatsu et al. 1987; Ishihara et al. 1992) developed for liquefiable soils in the freefield environment (Dashti et al. 2010a). However, recent observations of the performance of foundations suggest that settlement of rigid shallow foundations in liquefiable soils are commonly greater than those predicted in the free-field. Therefore, new correlations should be developed to better predict the degree of settlement of shallow foundations in liquefiable soils. Current research is beginning to focus on the mechanisms of settlement during liquefaction in regards to confining stress, pore-water pressure and shear stress induced from foundations (Dashti et al. 2010b)."

Jan 1, 2016

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.