Search Documents

By A. E. Cameron

The theory of atomic distribution of the stranger atoms in the space lattice of the solvent metal has been well developed by Rosenhain. It has long been known that the addition of one metal to another to form a solid solution increases the strength and hardness of the solvent metal. This increase is practically proportional to the amount of added substance up to the limit of solid solubility. To account for this increase in hardness and strength, Rosenhain assumes that the stranger atoms occupy positions on the solvent metal space lattice. Atomic attractions about the stranger atoms will not be the same as in the case of the pure metal, and there will thus be a disturbance of the orderly arrangement of the atoms on the space lattice, or a distortion of the lattice. Such a disturbance would interfere with the ease of slip along the planes and would thus tend to promote strength and hardness. Rosenhain notes that not only may there be a local disturbance of the lattice about the stranger atom but there may well be also a measurable change in the dimensions of the lattice as a whole. The relative amounts of local and general distortion of the lattice will depend upon the nature of the lattice itself. As Rosenhain says, "If the lattice is comparatively soft and flexible the distortion is likely to be largely local. In a stiff lattice, however, local distortion will be resisted and there will be a correspondingly increased general distortion."

Jan 1, 1927

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By Jack F. McQuat, Ross D. Lawrence

"Most geologists and mining engineers, in the course of their professional careers, frequently become involved with the appraisal of metalliferous mineral deposits and develop a familiarity with and standard approach to the evaluation of these deposits. When the same individuals approach the industrial mineral field, however, their usual approach pattern can be rudely disturbed.This paper highlights the difference in appraisal approach and outlines the factors common to both but which have entirely different emphasis. These comprise geological appraisal, analytical requirements, the importance of transportation, marketing requirements and standards, including appropriate allowances for product development, and marketing penetration.Out of these ""different"" considerations, however, a pat-tern or standard approach emerges which is as common to the industrial mineral field as that used either consciously or subconsciously in the metallic field.The paper reviews the different factors and points of emphasis and offers an outline of the common pattern of appraisal for industrial minerals."

Jan 1, 1971

By M A. Notte

Sand casting of steel is a process that offers the greatest design flexibility and highest metallurgical versatility. However, competition from other methods of fabrication is quite keen, constantly forcing the steel casting industry to the production of better quality castings at lower costs. New methods and materials have been put to use in the last ten years by foundries everywhere. This paper, in the form of a progress report, deals with new methods, processes and materials used by Canadian steel foundries for regular production, as well as with developments still in the initial but promising stages. T HE casting of steel to shape is the most direct method of producing steel parts in their final form. It is a basically economical process both as to cost and production time; it is also a process that offers design engineers the greatest flexibility and highest metallurgical versatility. In North America, the steel casting market has a normal yearly sales volume of 1,500,000 tons. In decreasing order, the largest customers are the railroads, construction machinery and earth-moving

Jan 1, 1965

By E. Krause, V. G. Papangelakis, S. Garg, R. Mahadevan, E. Edwards

"Bioleaching uses iron and sulfur-oxidizing bacteria to extract base metals from sulfide minerals. As bioleaching involves breaking the iron-sulfur bonds by ferric attack, the biologically mediated rate of iron oxidation is recognized to play a key role in influencing the overall kinetics. In this study, we investigate the catalytic ability of an indigenous AMD culture for oxidizing Fe(II) in solution. This culture was subsequently adapted on pyrrhotite tailings (0.6% Ni) by gradually increasing the solids loading. Results from this study show that such an adaptation reduces the initial lag phase in the biotic oxidation of Fe(II), thereby allowing for a higher Ni extraction when compared to experiments with an un-adapted culture at a similar solids loading. The use of adapted cultures also helps to reduce the residence time for bioleaching of Ni from pyrrhotite tailings. INTRODUCTIONAs the world demand for pure base metals grows; the mining industry is increasingly faced with the burden of processing lower grade ores and mining waste streams in order to recover the occluded metal VALUES ((Watling, 2006). The extractive metallurgy of nickel from sulfide minerals focuses on using a combination of mineral processing, pyrometallurgical (smelting) and hydrometallurgical techniques to extract Ni from its ore bodies.Pyrrhotite (Fe1-xS) is commonly found in association with pentlandite and chalcopyrite in sulfidic Ni ores, such as those found in Sudbury, Ontario, and in Russia, e.g. Norilsk. The vast majority of this pyrrhotite needs to be removed using mineral processing techniques, in order to minimize the Fe and S contents of the concentrates that proceed on to smelting. If all pyrrhotite were left in the concentrate, much more slag and SO2 would be produced, and the smelter throughput would be limited. Beneficiation of Ni sulfide ores leads to the rejection of unwanted constituents as mining wastes, which may still contain extractable amounts of Ni (Edgar Peek et al., 2010)."

Jan 1, 2012

Carrying Energy ?Energy ?Power, data, signal, hydraulics, pneumatics? ?Needs to be conveyed from a stationary point to a system in motion ?Cable Carriers (steel and plastic), Festoon Systems, Cable Reels and Bus Bars Polymer Cable Carriers ?Life Line for modern machinery ?Transmitting power, data, signal, hydraulics or pneumatic energy ?Constructed and designed to work in harsh environments, at high speeds and to do this continuously ?Meet a wide variety of cable (Media) requirements ?Virtually maintenance free ?High efficiency

Nov 1, 2011

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By E. Haccuria

Due to the growing share of electrical cars, the use of lithium ion batteries significantly increased. Recycling of these batteries is essential to safely dispose hazardous materials as well as to recover valuables (Cu, Ni, Co, etc.). In order to optimise the recycling process, accurate information is required on the slag phase equilibria for battery smelting. The slag is a multi-component system containing alumina from the battery cases, silica and lime from fluxes, and manganese and lithium from the electrode materials. The present study accurately determined the phase equilibria in the "MnO"-Al2O3-SiO2 sub-ternary system at metal alloy saturation. Particular attention was given to the accuracy and reliability of the final results by highlighting the different reaction pathways, mass transfer- and reaction mechanisms taking place in the system during experiments. This attention enabled improved experimental methodology and measurements. Based on the present study, further measurements will be undertaken in the quaternary "MnO"-Al2O3-CaO-SiO2 system at low "MnO" concentrations, which closely represents the future recycling industrial slags.

Jan 1, 2014

By D. D. Downing

This paper is a review of material selection considerations concerning protective coatings in the mining industry. The discussion will cover both capital-dollar projects and maintenance requirements. Emphasis will be on industrial finishes for structural steel and process equipment subjected to aggressive atmospheres. The presentation will cover the total needs of a job, emphasizing not only the owner's requirement for a cost-effective system during plant operations, but also taking into consideration the short-term requirements of general contractors, steel fabricators, erection firms and paint contractors.

Jan 1, 1979

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By Walter E. Montgomery

ACCIDENT-PREVENTION work in years gone by has been carried on by many mine managers as a philanthropic movement, but in recent years they have come to realise that Safety is good business and pays tangible dividends. Let us begin with the word itself. We are told that an accident is "any-thing occurring unexpectedly, undesignedly, or without known or assign-able cause'. It is further explained that it is any 'unpleasant or unfortunate occurrence involving injury, loss, suffering, or death", and, finally, "any unintentional or non-essential circumstance". We admit that accidents are unfortunate, unpleasant, unintentional, and they generally happen undesignedly and to a great degree unexpectedly, but to say that they happen "without known or assignable cause" leads us to believe that the word 'accident' is often misused. Would it not be more correct to say that a man suffered a "personal injury"? The word 'accident' in its proper sense implies something over which no one has any control, but when the majority of all so-called accidents are analysed we arrive at the incontestible fact that some act or action, previous or present, was the underlying cause. As long ago as the year 1556 this fact was mentioned by Georgius Agricola, who, in writing a paper on metallurgy, aptly stated, "It remains for me to speak on the ailments and accidents of mines, and of the methods by which they can guard against these, for we should always devote more care to maintaining our health, that we may freely perform the functions of our body, than to making profits". Farther on, Agricola relates in more detail, "Sometimes workmen slipping from ladders into the shafts break their arms, legs, or necks, or fall into the sumps and are drowned; often, indeed, the negligence of the foreman is to blame, for it is his special work both to fix the ladder so firmly to the timbers that they cannot break away, and to cover so securely with planks the sumps at the bottom of the shafts, that the planks cannot be moved nor the men fall into the water; wherefore the foreman must carefully execute his own work. Moreover, he must not set the entrance of the shaft-house toward the north wind, lest in winter the ladders freeze with cold, for when this happens the man's hands become stiff and slipping with cold, and cannot perform their office of holding. The men, too, must be careful that, even if none of these things happen, they do not fall from their own carelessness'.

Jan 1, 1938

By O. Lundhede

Today, systems and machinery usually are designed to meet only one specific customer?s requirements. One reason for this is that underground automation and smart functions are often developed tightly together with a customer. This is natural, since risk and cost can be shared between the customer and the supplier. Nevertheless, when the automation product develops and the market increase this will cause problems: The highly specialized products will not fulfill the next customer?s demands. In order to cope with this problem, Atlas Copco works towards a common platform. Instead of designing solutions for specific customers, we will lift the abstraction and focus on standardized modules. These modules, or function blocks, can then be combined in a large variety of configurations. The benefits of combining modules into products are, for example: increased flexibility when options are available for many machines; easier commissioning and maintenance since less different spare parts and tools are needed; and easier operation since the user interfaces have a similar look and feel. This paper will present the ongoing work towards standardized modules. We will discuss how our Rig Control System (RCS) allows for modular design at Atlas Copco. RCS has number of standardized modules that are used in different surface and underground mining and tunneling equipment. These modules are also used for optional products such as, drilling, radio-remote control, and telematics systems.

Aug 1, 2013

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

?Podolsky Water treatment plant discharges to Norman North bog which drains into Whistle / Post Creek watershed and into Wanapitei Lake ?Whistle Mine closed and reclaimed but continues to treat and discharge water to Whistle Creek

May 1, 2009

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019