Search Documents

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By N. J. Shackleton, N. A. Chapman, V. Malysiak, C. T. O’Connor

In this study, the effect of using conventional crushing and high-pressure grinding rolls (HPGR) in combination with dry or wet milling was investigated using a base-metal sulphide (BMS) sphalerite and a platinum group mineral (PGM) ore to determine how these processes affect the flotation performance. In sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc, whereas in PGMs, similar treatment produced the poorest results. The results were investigated further by the effect of factors such as percentage liberation and particle size on the flotation results.

Jan 1, 2012

By J. L. Llanca

The New Level Mine project (NLMP), the planned underground expansion of the El Teniente mine in Rancagua, Chile, is expected to reach a daily extraction rate of 137 to 180 ktpd upon achieving full capacity. Production is planned to start in the year 2017 and the current plan is to meet that target through two development phases, from the year 2012 to 2014 and from the year 2015 to 2017. To achieve the 2012 to 2014 underground development schedule, the ventilation requirements have been estimated in the range of 189 m3/s (400 kcfm), and cannot be made available without significant modifications to the current system of El Teniente. As a result, a certain number of alternatives were explored to find a solution to this shortfall, for example, adding raises to generate parallel airways and installing fans to reinforce the current ventilation system. From the alternatives studied, the installation of a second main fan (system) in parallel to an existing one was identified as the best solution, and selected for implementation, however the location was not ideal and there were concerns as to the operation of both fans once the second fan was installed. This paper presents the study used to estimate the operational points of both the current and the new fan, and to justify the parallel installation of the additional main fan. An additional computational fluid dynamics study was undertaken to validate the operational point, given the particular geometry of the fan?s location and placement, to guarantee a stable operation of the fans. Finally, the protocols arising out of this work for starting the fans, and operating them in parallel to avoid generating a stall condition and damaging the investment are discussed.

Aug 1, 2013

By L. W. Krahenbil

The programmable Logic Controller (PLC), at its present stage of evolution, is now considered as a mature control system. The PLC combines the solid-state reliability of hardwired logic and computer control systems with the simplicity of a relay ladder logic. Relay symbolic programming through a function-oriented keyboard provides a means which plant personnel can easily become accustomed to work with. In a large coal facility, it is shown that the control engineer can provide improved control flexibility with the advanced capabilities of the PLC.

Jan 1, 1979

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By P. Cavanagh

Summary This paper discusses the fundamental principles which allow the development of a new method for studying the deformation and failure of metals in terms of &apos;internal microstrains&apos;. Internal microstrains mechanical and magnetic properties are defined and their influence on of metals is outlined. A research programme at present in progress will determine whether magnetic measurements of internal microstrains give sufficiently accurate values for predicting the performance of metals under service conditions. These magnetic test techniques are also being used to detect the beginning of plastic deformation and to trace the development of deformation processes and failure. Results of the experimental work in each field will be published. Introduction Any attempts are being made to develop a complete theory embracing the mechanical behaviour of metals. In spite of the amount of experimental data available, the theoretical approach is rather difficult, since most of the mechanical properties of a metal are determined by deviations from the pure chemical composition or the perfect crystal. Both types of deviation are difficult to reproduce experimentally and to describe theoretically. In general, there are three main avenues of approach to the problem being followed today.

Jan 1, 1950

By B. Yamamoto, D. Post, J. De Leon, A. Meike

"This paper describes the theory, design, building, and testing of the passive magnetic bearing stabilizing system which is the core of the passive magnetic bearing system. The stabilizing system is made up of two large magnetic disks opposing themselves with a stabilizing disk in the center which allows the system to self-locate in a null position without the need for external power sources or sensors. When outside forces act upon the stabilizer, the magnetic fields interact with the stabilizing plate to return the system to its null position. Collaboration between two industry leaders has allowed an actual prototype to be built and tested providing real data to prove out the theory.INTRODUCTIONMagnetic bearing/stabilizer systems have many advantages over conventional mechanical bearing systems. These include near-zero drag losses and no need for lubrication since the rotating elements make no mechanical contact with the stationary elements of the bearing system. However all magnetic bearing systems must contend with a constraint known as Earnshaw’s Theorem in the early 1800’s, this theorem asserts the impossibility of constructing a stable, non-contacting, electrostatic or magnetostatic levitation system using only fixed charges or fixed magnetic poles, such as those produced by permanent magnets. Because of the constraint imposed by Earnshaw’s Theorem virtually all present-day commercial magnetic bearing systems are of the “active” type. That is, they employ electromagnets that are powered by amplifiers the inputs to which come from sensors embedded in the bearing system. These sensors are a part of a feedback loop that operates to keep the levitated rotating parts of the bearing stable and centered. The resulting complexity means that active magnetic bearings are expensive, require periodic maintenance, and continuously consume electrical power to energize their amplifiers and their electromagnets.Passive magnetic bearings are, of course, also subject to the constraints imposed by Earnshaw’s Theorem but they solve this problem in a straightforward and simple way, with only “passive” elements that take advantage of a loophole implicit in the derivation of Earnshaw’s Theorem. This loophole is that Earnshaw’s Theorem as derived applies only to static systems, i.e. an assembly of stationary permanent magnets arranged so as to levitate an object containing other permanent magnets. The theorem can be overcome if dynamic effects are taken into account. In active magnetic bearings the “dynamic effects” involve the afore-mentioned sensors, amplifiers, and electromagnets."

Jan 1, 2012

By Ross D. Lawrence

"IntroductionOne of the methods used when applying the Market Approach to the valuation of a mineral exploration property is known as the Joint Venture Terms Method. The method is particularly useful for the valuation of early-stage exploration properties. Unfortunately, valuators are sometimes imprecise in distinguishing between joint ventures and other types of transactions.At VALMIN '94, Bob Appleyard1 proposed that, if one ignores the time value of money and the probability that the expenditure commitment would be completed, the formula to calculate the value ($V) of a property owned by Party B at the time of the deal would be:$V =$Ex (100-1%)/1% (Formula I)Where $V is the value of the property2Where $E is the expenditure commitment by Party A, andWhere 1% is the percentage property interest to be earned by party A.At PACRIM '99, Mike Lawrence and Graham Dewar3 referred to this method and suggested that there was an ambiguity in the formula proposed by Appleyard in 1994. Mike Lawrence referred to this problem again at VALMIN '014•Lawrence & Dewar suggested that the formulashould be:$V100% =($Ell%) x 100 (Formula 2)Where $V 100% is the value of the entire property,Where $E is the expenditure commitment by Party B, andWhere 1% is the percentage property interest to be earned by Party B.Subsequently, there has been considerable discussion in the AuslMM Bulletin5. In my view, this discussion has touched on a number of useful points, but generally has overlooked one essential element needed for an understanding of the correct application of the N Terms method. That essential element is to understand that there is a material difference between (1) entering into a joint venture arrangement and (2) the purchase of an interest in a property."

Jan 1, 2003

The Shortage of Mining and Metallurgical Engineers I N many parts of the Western World attention has recently been drawn to the acute shortage of mining and metallurgical engineers produced by the universities. Naturally, the reasons for this shortage have been discussed, and various remedies for it have been proposed. In this paper, I want to examine some of them. It is now fairly generally ac-cepted among mining men that the easy attractions of modern urban life have left the career of mining in the metaphorical as well as in the literal backwoods. The industry finds it increasingly difficult to recruit adventurous and intelligent young men; for such men now seek their intellectual, if not physical, adventure in more glamorous occupations from a safe social base in suburbia. The salaries, opportunities and security offered by the mining industry do not complete effectively with the rewards offered by other industries and by commerce, taking into account the social disadvantages of a mining life. The excitement and other non-material attractions of mining

Jan 1, 1965

About Barrick Paste Backfill at Barrick Goldstrike Rodeo Paste Plant Cyclone Lab Testing Challenges and Lessons Learned Future Barrick Projects

May 1, 2013

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By M. Matthias

A study, part of a doctoral dissertation (Matthias, 1991), was conducted during 1987 and 1988 to establish the means by which professionals assess and maintain their competence during the various stages of their careers. The study elicited responses from fifty-nine subjects representing engineering, pharmacy and medicine (twenty subjects from engineering, nineteen from pharmacy and twenty from medicine) on their perception and assessment of continuing competence. The findings revealed a wide variation of how professionals perceived their continuing competence and the means they adopted to keep current. The implications of the study are significant for adult education practice and theory building. The author strongly believes that now, more than ever, engineers must take ownership of their careers and professional development activities. While management and supervision have a key role to play, it is the engineer, who is ultimately responsible for the scope, planning and implementation of her/ his professional development needs. An example from one high technology company will illustrate these points.

Jan 1, 1999

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

By Gregory C. More O'Ferrall

Generally pillars in the Southern African hard rock tabular underground mining environment are designed using either empirical pillar design formulae or numerical modelling (analytical) methods utilizing the Hoek-Brown failure criterion. However, none of the pillar design methodologies employed takes cognizance of weak layers either within the pillar material or in the immediate foundation of the pillar. Over the past few years, the presence of a weak layer either within the pillar material or within the immediate foundation of the pillar has resulted in the closure of one platinum mine (Everest Mine), closure of one chrome mine (Wonderkop Chrome) and large-scale instability in a couple of chrome and platinum mines in South Africa and Zimbabwe. A study has been initiated to better understand the failure mode and strengths of the pillars where pillar failure associated with weak layers occurred. Owing to the infancy of the study into the failed pillar strength and failure mechanism, the purpose of this paper is to highlight the circumstances that led to the collapse of mining sections and a shaft, and the difficulty associated with designing pillars in the Southern African chrome and platinum mining operations.

Jun 1, 2012