Search Documents

By M. B. B. Research Council of Alberta Crockford

Introduction Kootenay strata of Lower Cretaceous age contain much of the highest rank coal produced in Alberta. These strata outcrop in the foothills and mountains of southwestern Alberta and southeastern British Columbia, and the economic value of the coal seams contained in them was evident to the earliest explorers, who refer co them in their journals. Lacer, investigation of the .coal measures was undertaken by prospectors and by a succession of geologists, most of whom were in the employ of the Federal government, but some acted for private interests. Surveys by these men proved chat foothills and mountain regions hold immense quantities of high-grade coal within easy reach of transportation facilities, and their conclusions have accelerated the development of the coal-mining industry m Alberta. Among geologists who have contributed much to our knowledge of the region are J. M. Dawson, G. M. Dawson, R. C. McConnell, D. B. Dowling, J. D. Mackenzie, B. Rose, J. R. Marshall, B. Rose, J. R. Marshall, B. R. McKay, J. A. Allan, and J. L. Carr. The present paper is to a great extent a compilation of the work of the above men and of several others who have investigated the area lying between Bow river and Crowsnest pass. Space does not permit a list of all the sources of information so chat only chose of prime importance are given in the text. Data for the map and ?cross-sections of Figure 1 were taken from the following published maps of the Geological Survey of Canada: Cascade Coal Basin, Pub. 933; Canmore, Maps 322 and 323; Upper Elk River and Upper Highwood Rivers, Pub. l980; Blairmore, Pub. 1584; Southfork Coal Area Map l03A; and of the Research Council of Alberta: Highwood-Elbow Area, Map 20; and Ribbon Creek Area, Map 21. In some cases, the cross-sections have been simplified or otherwise altered, and for these revisions the writer cakes full responsibility. The stratigraphic sections of Figure 2 have been taken from published reports of the above mentioned organizations. The area covered in this paper is shown in Figure l. It is wholly within Alberta, and reaches from township 5 to township 27 and from range 1 co range 11, west of the fifth meridian. Its location is about fifty miles west of both Calgary and Lethbridge. Topography of the area ranges from foothill on the east to mountainous on the west. In this paper' the foothill region is considered to be chat which lies immediately east of the most easterly mountain ranges, such as Livingstone and Highwood. There are two principal coal mining districts in the area, one served by the main line of the Canadian ?Pacific railway and centring about Canmore, the other by a branch line of che same railway and centring about Bellevue, Blairmore, and Coleman.

Jan 1, 1949

CHALLENGES TO SCHEDULE/BUDGET Shortage of people (contractors, vendor support, engineering, staff) 2007 projects off the shelf Increase in metals prices Shortage of large tires Reserve increase Size of mine Unskilled labor force Community/government relations Limited access into valley English to Spanish SOLUTION Line 1 Line 2 concurrent construction, EPCM engineering review, advance scheduling Placed line 2 orders earlier Hedged currency, bulk orders Strategic alliances Flexible design Plan Deliveries Training, multiple contractors Engagement Built/upgraded roads Technical translators

May 1, 2010

By Matt Schuett

Antamina Mine Facts • Surface Water Design Principles • Drainage Areas • SEDCAD Modeling • Impacted Runoff Collection • Clean Runoff Collection • System Flexibility • Outfall Construction

May 1, 2004

The properties required for a com-pound to form useful thermoelectric materials are described. Uranium compounds which might have these properties are reviewed. Several of these compounds have been prepared and fabricated into compacts. The apparatus used for hot pressing, and for the measurement of thermoelectric power, electrical conductivity and thermal conductivity, is described. Detailed attention has been given to the properties of the nitrides. Preliminary studies on a number of other uranium compounds are reported. The figures of merit of the best materials so far examined are one-tenth of those necessary for a useful thermo-electric material. THE efficiency of thermoelectric materials for power generation and cooling is determined by their figure of merit, Z = a2 a/K, where a, a and K are thermoelectric power, electrical conductivity and thermal conductivity, respectively. It is well known that the largest values of Z are achieved with semiconductors (1). High mobility of charge carriers is necessary for simultaneously high thermoelectric power and electrical conductivity.The properties required for a com-pound to form useful thermoelectric materials are described. Uranium compounds which might have these properties are reviewed. Several of these compounds have been prepared and fabricated into compacts. The apparatus used for hot pressing, and for the measurement of thermoelectric power, electrical conductivity and thermal conductivity, is described. Detailed attention has been given to the properties of the nitrides. Preliminary studies on a number of other uranium compounds are reported. The figures of merit of the best materials so far examined are one-tenth of those necessary for a useful thermo-electric material. THE efficiency of thermoelectric materials for power generation and cooling is determined by their figure of merit, Z = a2 a/K, where a, a and K are thermoelectric power, electrical conductivity and thermal conductivity, respectively. It is well known that the largest values of Z are achieved with semiconductors (1). High mobility of charge carriers is necessary for simultaneously high thermoelectric power and electrical conductivity.

Jan 1, 1963

By J. -F. Blais, M. -O. Simonnot, J. Mocellin, G. Mercier, J. -L. Morel

Large quantities of ferromanganese sludge are generated as waste material by blast furnace during the manufacturing of ferromanganese. These slags are very rich in manganese, zinc and lead (5 to 40 %). These residues have been deposited in a pond in periphery of the steel industry. Considering the market value of the metals, these brownfield sites can now be considered as secondary resources. We have developed a hydrometallurgical process for selectively leaching Zn, Mn and Pb in order to produce compounds of Mn and Zn pure enough to be economically recoverable and a residue rich in Pb. Batch laboratory experiments were carried out to determine appropriate leaching conditions to maximize zinc extraction (100 %) and manganese extraction (90.0 %) with sulfuric acid and to generate a residue containing 15 to 30% of lead. This Pb residue is recyclable by another process.

Jan 1, 2015

By Ron Zevenhoven

In Finland one opportunity for large-scale CO2 capture, utilisation and storage (CCUS) is CO2 mineralisation, i.e. mineral carbonation. A process route under development towards industrial application involves production of magnesium hydroxide or sulphate from serpentinite rock (serpentine = 3MgO·2SiO2·2H2O), followed by conversion either in a pressurised fluidised bed (PFB) reactor, giving magnesium carbonate, or in an aqueous solution process giving magnesium hydro-magnesites. Iron present in the rock is typically obtained FeO(OH). Results obtained with these process routes and progress towards industrial demonstration is addressed, process heat integration and operation on flue gases (without CO2 pre-separation!) being key features for economic viability. A process route utilizing calcium-containing slag by-product from iron- and steelmaking under development towards large-scale application is the so-called slag2pcc concept. It converts an industrial by-product into valuable material, reduces use of natural material and streams to landfills while binding CO2 produced by the process generating the slag. Using ammonium salts, calcium is extracted from steel converter (BOF) slags and subsequently carbonated in a two-stage aqueous process (at ambient temperatures and pressures). Precipitated calcium carbonate (PCC) is produced while regenerating the ammonium salt. Process performance and scale-up while guaranteeing a certain PCC quality are presented.

Jan 1, 2015

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By H. Tsuruta, A. Fujibayashi, I. Sumi, A. Murao, R. Murai

Injection of biomass into blast furnace as alternative reducing agent is so effective for the purpose of mitigation of carbon dioxide emissions from steel industries, because biomass is considered to be carbon neutral raw materials. Certain amount of Palm Kernel Shell (PKS) is abandoned after Palm oil extraction process. To use as a reducing agent of blast furnace, PKS was carbonized and classified by 100 mesh sieve. To examine the gasification behavior of PKS carbide under the blast furnace conditions, several combustion experiments were conducted using hot model experimental furnace. The experimental results showed that the gasification efficiency of PKS carbide increased as the quantity of volatile matter increased. This tendency is the almost the same for the pulverized coal, so carbide of PKS can be used at blast furnace at appropriate amount of volatile matter that can be controlled by carbonization condition. In addition, the pressure drop of the furnace tends to decrease because the amount of ash in PKS carbide may be smaller than that of pulverized coal. PKS carbide is a suitable reducing agent in that respect.

Jan 1, 2015

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By Tanai Marin

Modelling of pyrometallurgical processes can become extremely challenging when the process involves complex chemical reactions, phase change, multiphase flows, heat and mass transfer and fluid flow. Traditionally modelling involving complex thermodynamic equilibrium and thermochemistry are treated separately from problems in which transport phenomena are dominant, such as CFD and heat transfer studies. The separation is also necessary due to the lack of modelling tools that can effectively couple both solution thermodynamic and transport phenomena or even multiphysics problems. However, there are, quite often, problems in high temperature process metallurgy in which it is not possible to simplify this two modelling approaches. Typical cases of this are for example, the modelling of slag freezing on furnace walls (electric or flash furnaces) to create a protective layer in front of the refractories hot wall, the formation of build up from the matte or metal phases at the hearth of the furnace, calcine smelting from charging piles into slag phase, etc. The problem is even more challenging in nonferrous pyrometallurgy as most, if not all, of the condense phases are highly non ideal solutions involving several components and exhibiting complex crystallization paths and miscibility gaps, such as the Fe-Ni-Cu-S matte, FeO-Fe2O3-SiO2, FeO-MgO-SiO2 slags, etc. In this paper, an approach to model coupled problems involving multiphysics and solution thermodynamic is presented. The approach consists in developing in-house a library containing the Gibbs energy minimization routines and using the local equilibrium concept for process modelling from a multiphysics commercial software (COMSOL). Simple test cases, such as building a non-ideal binary phase diagram on a CFD package is presented, the limitations and of other classic approaches such as equilibrium or Scheil cooling are discussed and compared to this model.

Jan 1, 2015

By G. R. Cope, J. S. Getsinger, K. D. Lund, T. Neale

"Mineral exploration in the Sicker Group, a belt of Paleozoic volcano-sedimentary rocks on Vancouver Island, has traditionally centred on auriferous polymetallic volcanogenic massive sulphide deposits such as those currently mined by Westmin Resources Ltd. near Buttle Lake. Recently, however, the focus of exploration in the Sicker Group has shifted toward targets of structurally controlled gold concentrations, with notable success. Major north and northwesterly-trending structural features such as the Cowichan-Horne Lake break (one of several regional high-angle thrust fault s active throughout a long period of geological time) and related fault systems have contributed to localization of gold mineralization.Using the extensive information database compiled by MPH Consulting Limited during numerous exploration projects in the Sicker Group, two cross sections through areas with significant gold occurrences southeast of Port Alberni are presented. The cross sections combine geological, geochemical and geophysical data in an attempt to emphasize the relationship between structural trends and gold mineralization. Examples from specific properties, including gold discoveries along the Mineral Creek fault zone, are used to illustrate this relationship."

Jan 1, 1990

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The use of large AG/SAG mills in the mineral industry has been on the rise recently due to a significant reduction in the capital and operating costs for achieving significant increases in plant throughputs. The major reason for downtimes in these mills is the time taken for the replacement of broken or worn liners. This loss of “availability” of these units has a significant impact on the productivity of these plant operations. The ability to predict liner life time and its evolving shape could help to optimize these comminution operations. In the past decades, various models have been proposed to estimate liner wear rate, but because of their empirical nature they could only be used within certain limited operating conditions. In this research, a phenomenological model which could predict the liner wear rate was proposed and tested. This model considers parameters such as; operating conditions, liner hardness, pressure on the lifter, and, relative velocity of particles and mill shell. Data from industrially measured liner profiles were taken during the liner life time at the Sarcheshmeh and the Gol-E-Ghohar SAG mills to provide a solid base to calibrate and validate the model. The comparison of the model predictions with the actual measurements of the liner wear rate showed that the results were in a good agreement at both, the Sarcheshmeh (R2=0.94), and the Gol-E-Ghohar (R2=0.97) concentrators.INTRODUCTIONAG/SAG mills are one of the most important technologies in the mineral processing industry in the recent decades. The “Availability” of these units in a plant operation is one of the most important economic parameter for evaluating their performance. The major reason for the downtime of these mills affecting their “availability”, is the time required to change worn or broken liners (Yahyaei, Banisi, & Hadizadeh, 2009; Maleki-Moghaddam, Yahyaei, & Banisi, 2012). The knowledge about the magnitude and profile of liner wear not only enables more accurate liner life estimation to prevent unwanted interruptions of the SAG milling in mineral processing plants and more strategically plan the scheduled mill outages for liner changes. It also could provide key information needed to select an appropriate liner design (Yahyaei et al., 2009; Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010a)."

Jan 1, 2016

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By Matt Manson

Renard?1-10 kimberlite pipes and ?Lynx-Hibou?kimberlite dyke system within ?Foxtrot?property 50/50 JV with SOQUEM, Stornoway operator 2001: Discovery of the Renard kimberlite pipes 2003: Discovery of the Lynx-Hibou kimberlite dykes 2006-2007: Bulk sample program 2008: First 43-101 Resource and Preliminary Assessment 2009/2010: Updated 43-101 Resource

May 1, 2010

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By Z. Q. Liu, J. M. Du

"On the basis of analyzing current design and applications, the structure form, working loads and design principles of shaft sinking headframe are summarized in this paper. To overcome the insufficient bearing capacity and geometry size of the finalized shaft sinking headframe in China, a series of new large shaft sinking headframe were developed under vertical shaft construction conditions of maximum net diameter of 12.0 m and maximum depth of 1200 m. The new series shaft sinking headframe include two sets (with single sheave platform and double sheave platform), three dimensions (optimum shaft diameter <8.0 m, 8.0-10.0 m, and 10.0-12.0 m, respectively) for each set, and has innovation and optimization on structure of the sheave wheel platform (MU type) and bracing frame (REN and ZHONG type). The largest new shaft sinking headframe can arrange up to 4 hoisting equipment simultaneously and has bearing capacity more than 10000 kN. Two of the new shaft sinking headframe were successfully applied in practical engineering, such as the Hulusu auxiliary shaft, the Dahaize 1# auxiliary shaftand Sishanling auxiliary shaft. These applications showed that the new shaft sinking headframe has sufficient bearing capacity and reliable applicability. The new shaft sinking headframe could provide an effective guarantee for safety and efficiency sinking of deep-large shaft in the future.INTRODUCTIONShaft sinking headframe is one of the basic shaft sinking structures and it is mainly for hanging hoisting containers and sinking facilities in sinking a vertical shaft (Yu & Shi, 1991; Wang, Jing, & Liu, 2007). Currently, 7 types of steel pipe sinking headframe are used in China, which are mainly finalized by the Ministry of Coal Industry of China (Wang, 1988). As shown in Table 1, V-type is the largest of them and it is only suitable for sinking shaft of diameter less than 8 m and depth less than 1 000 m(Yang, 1982). However, with the increase of mining depth and scale of mineral resources in China, the diameter and depth of newly built vertical shaft are increasing continuously (Xie, Zhou, Xue, Wang, Zhang, & Gao, 2012; Qi & Pu, 2013). At present, the maximum net diameter of vertical shaft is close to 12 m, and the maximum depth is more than 1600 m (Yang & Chen, 2015; Xu, Yang, Liu, & Qin, 2015). The shaft sinking headframe has become the main restrictive factor for the development of sinking equipment, such as the height of muck discharging platform cannot meet the usage requirement of hydraulic umbrella driller, the size of sheave wheel platform is difficult to arrange the increasing hoisting and suspension equipment, the bearing capacity is insufficient to meet the needs of multiple hoisting loads in sinking a deep-large shaft, etc. Therefore, development of new shaft sinking headframe for deep-large shaft (>1000 m in depth and 8~12 m in diameter) is urgently required for China and also the whole world."

Jan 1, 2019

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

By Z. Z. Öztürk, N. Sarica, A. H. Üçisik, C. Bindal

"Titanium oxide films were fabricated on commercially pure titanium surfaces via anodization procedure. Anodization parameters, anodization time and voltage were altered, whereas temperature and chemical composition of anodization bath were kept constant. The main idea in this study is to obtain rough titanium-oxide surfaces. The type and feature of titanium oxide formed were observed via SEM and EDX analyses. What was revealed from SEM and EDX analyses were combined with Ti-O phase diagram in order to make judgment on the type of phases obtained, e.g. solid solution and/or compounds. Studies on the different regions of each sample showed that surfaces consist of different titanium oxide compounds with various O/Ti ratios in nano level and solid solutions varying in terms of chemistry on the same sample. Thus together rough surfaces and inhomogeneous distribution of "titanium oxides" were obtained. It was also found that when anodization time and voltage were increased, more granular surface with higher O/Ti atomic ratio was obtained."

Jan 1, 2015