Search Documents

By D. A. Jacobson

Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product. The MP1250?s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint.

Jan 1, 2012

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By M. J. McLeod, D. R. Lux, R. P. Taylor

"The Mount Douglas Granite constitutes the eastern part of the Saint George Batholith and contains the youngest, most differentiated phases of the batholith. It also contains extensive endogranitic, low-grade. Sn- W-Mo-bearing sheeted vein systems. Early phases of the Mount Douglas Granite are coarse- to medium-grained, seriate granites that represent the slowly cooled carapace of the intrusion. Late phases are medium- to fine-grained, equigranular and porphyritic granites that were accompanied by repeated and widespread fracturing of the carapace and injection of mineralizing fluids. These granites represent a highly differentiated suite with ""A "" type affinities developed in a ""within plate"" transitional to ""syn-collision"" tectonic setting. 4oAr/ 39Ar dates for biotites from the various phases indicate emplacement circa 367 Ma.The linear distribution of some phases in the Mount Douglas Granite and the systematic orientations of sheeted veins along tensional fractures indicate structural control on granite emplacement and vein distribution. This type of relatively passive endogranitic mineralization is unique in the granites of southern New Brunswick and contrasts markedly with highly fluidized systems operative elsewhere in the area. IntroductionInvestigation of Sn-W-Mo occurrences in New Brunswick has shown that most of this mineralization is associated with late, highly differentiated phases of post-orogenic (Acadian) granitoid magmatism that occurred during Devonian and Early Carboniferous time (Ruitenberg and Fyffe, 1982; Taylor et al., 1988). The polymetallic Mount Pleasant Sn-W-Mo deposit (Ruitenberg, 1967, 1972; Kooiman et al., 1986)and the Burnt Hill W deposit are two orebodies of this type in New Brunswick. Numerous smaller deposits associated with these granitoid rocks in southwestern New Brunswick have been documented in previous investigations (Ruitenberg, 1967, 1968; Ruitenberg and Fyffe, 1982; Taylor et al., 1985; Lentz, 1985)."

Jan 1, 1988

By J. -F. Lessard

Most underground mines rely on ore pass systems to ensure the transport of ore and waste. The design and operation of ore pass systems often rely on past experience, which is often anecdotal and at times contradictory in nature. This paper summarizes the current practice in Quebec underground metaliferous mines. The information was collected during a series of site visits in ten underground mines. The database includes information on ore pass configuration, support, materials transited, and overall ore pass performance.

Jan 1, 2006

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By P. D. R. Maltby

"With the narrow vein structure of Nova Scotia gold deposits, selective mining is rarely possible and mill heads will be too low (below 0.10 oz per ton of gold) to support a conventional mill of up to 1000 ton per day capacity at present gold prices. The recent operation of a small 100 t.p.d. mill at Cochrane Hill using fine grinding - leaching - filtration supported this assertion. Milling costs exceeded $25.00/ton of feed mainly due to high capital, labour and maintenance costs.Accordingly, since 1981, efforts have been directed towards the development of a cheap gold extraction process in terms of both capital and operating costs. The main criteria is to produce gold below US $200 per oz including all administration, mining and process stages. This paper describes such a process development for Cochrane Hill. LOCATION AND HISTORY OF THE PROPERTYThe Cochrane Hill property is located about 8 miles North of Sherbrooke, N.S. on highway No. 7. Sherbrooke is about 180 miles east of Halifax. Gold was originally discovered at Cochrane Hill in the 1860's. Early work consisted of trenching. In the 1930's a small shaft was sunk to about 80 feet and some tonnage treated using a stamp mill with gravity concentration of gold.Northumberland Mines Ltd. acquired a 70% interest in the property in 1977. Subsequent drilling indicated a potential zone of gold mineralization with a drill-indicated tonnage of one million tons having a grade of 0.07 ounces per ton of gold (all high assays cut to 1 oz) down to a depth of 300 feet recoverable by open pit mining methods. In broad terms, the goldbearing zone is about 50 feet wide and 800 feet long and dips at about 70°."

Jan 1, 1984

By Steven W. Wilson, Brigitte Lacouture, Nichola A. McKay

"The Aqqaluk deposit is a lead-zinc ore body that lies immediately north of the Main Pit at Teck Cominco’s Red Dog Mine in Alaska. It is scheduled to begin production in 2011 or 2012. A project team was formed in late 2004 to plan and implement an ore characterisation and metallurgical evaluation on the Aqqaluk ore. The main objective of this program was to facilitate the transition from Main Pit to Aqqaluk ore in the Red Dog concentrator. The program will develop a detailed, spatially-oriented characterisation of the Aqqaluk deposit attributes including lithology, ore geochemistry, bulk mineralogy, ore texture, as well as evaluating the metallurgical characteristics of ore hardness, process water geochemistry, bench-scale floatability and mineral liberation in ground feed, concentrate and tails. Developing correlations between the metallurgical response and the ore characterisation data is key to the emerging science of geometallurgy. This on-going program is a technical due diligence study that aims to reduce the risk associated with processing a new ore and to provide predictive information for mining and stockpile preparation.The test work to date has focused on characterising the five ore zones currently identified in the Aqqaluk deposit, namely: Siliceous (sub-divided to High Zn:Fe and Low Zn:Fe), Vein, Median Plate and Baritic ores. It identified a number of challenges associated with surface oxidation, or weathering, of the core samples and outlined a program for future sample collection and storage. Metallurgical testing evaluated ore hardness by a variety of methods. Preliminary floatability studies have been completed and some initial links have been established between the ore characteristics and the flotation response. Soluble mineral weathering products, the relative abundance of pyrite and marcasite and the iron content in the sphalerite grains have all shown a correlation to mineral recovery.As new core is received, both the ore characterisation and the metallurgical testing will be continued with a view to strengthen the existing correlations and develop new links."

Jan 1, 2007

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

"Generation and removal of fines are considered in the context of the mill and classifier as a single-unit process in which grinding rates and mechanisms, mill residence time distribution, circulating load, and classifier performance all interact to effect the overall grinding circuit productivity. Required process design specifications are identified, and a computer assisted design procedure for application of hydrocyclones in closed circuit grinding is presented. INTRODUCTIONThe purpose of the grinding circuit is to carry out the size reduction necessary to suitably prepare material for the upgrading process(I) The desired product size specification being the d1st1nguishing criterion between the ""fines"" (smaller than desired product size) and the ""coarse"" fraction (larger than desired product size), the capability of the grinding circuit to perform its task effectively depends on the nature of two processes that are taking place;(a) size reduction of the coarse material, and,(b) removal of fines from the system."

Jan 1, 1984

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962

By M. A. Upham

"MINING is Canada's second largest basic industry, producing material with a gross value of 2.5 billion dollars, led only by agriculture with 2.9 billion dollars. It pro-vides employment, directly and in-directly, for three quarters of a million people. Since the Second War, the value of mineral production in Canada has tripled. Economists forecast that over the next 15 years its value will triple again. Canada is a basic and leading supplier of nickel, iron, copper, zinc, lead and uranium. It is also a major oil producer, leads the world in the production of asbestos and in five years will be the leading producer of potash, a basic constituent of fertilizer.It can be seen that Canada's wealth and economic progress lies in being a primary producer of economic minerals and in building secondary industries to manufacture finished products from these raw materials. Canada's future in the field of mineral production looks bright, with our resources just starting to be tapped. Outside of the large expanse of Soviet Russia, we are by far the world's most fertile mineral exploration area."

Jan 1, 1967

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By Nathan P. Schmidt

Climate and hydrology data are required during all phases of mining projects, including impact assessment, mine planning and design, operational water management and mine closure and reclamation design. In the Canadian north, data sources are spatially sparse and often short-term in nature, and design parameters are often estimated based on data collected at sites far distant. Confidence in such data can be increased by verification or modification using data collected during properly implemented baseline and operational monitoring programs. A data set that accurately reflects conditions at the project is more readily accepted by regulatory agencies during the permitting process, and allows development of more effective and economic water management, mitigation measures and compensation. Data requirements and collection methods for developing an adequate data set for mine development are reviewed. These are illustrated using examples from oil sands, diamond and metal mines in the Canadian north.

May 1, 2004

By Louis J. Cabri, Donald Hoy

"Samples with contrasting gold mineralization were studied quantitatively prior to metallurgical tests. The AD samples are coarser-grained and characterized by abundant Sb minerals (jamesonite, berthierite, stibnite). The finer-grained MW sample has abundant pyrite and pyrrhotite, with arsenopyrite and galena next in abundance. A large number of gold mineral particles were determined by SEM investigation of hydroseparation concentrates, ranging from 150 to 597 per sample. The grain-size distribution of the gold minerals shows evidence of bimodal grain-size distributions (volume %), with the coarse fraction being most significant in sample MW-1 (maximum ECD=308µm). The coarsest gold minerals in the AD samples range from 139µm to 281µm ECD.The deportment of gold minerals is as electrum, aurostibite, native gold, and a possible new mineral (AuNiSb4). Gold also occurs in nisbite. The gold minerals are dominated by electrum in three samples and aurostibite is next in abundance. The major gold minerals are probably representative of three stages of gold mineralization. The first stage is represented by electrum, which is partly to completely replaced by Sb-rich mineralization forming aurostibite, and the last stage is native gold, often occurring as rims on one or the other earlier gold mineral. The gold minerals are strongly associated with sulphides in the AD samples (55 to 60 vol.%). At the grind used for the hydroseparation the liberated gold mineral quantity (volume %) is also significant, ranging from 65% for sample MW-1 to 30 to 37% for the AD samples.INTRODUCTIONThe Clarence Stream deposit is located 70 km south-southwest of Fredericton and 25 km northnorthwest of St. George, south-western New Brunswick, near the international boundary with Maine (Fig. 1)."

Jan 1, 2007

By Derek H. C. Wilton

"The Nain Province (NP) of northern Labrador is a >600 km long by =100 km wide Archean craton that has undergone relatively little mineral exploration until economically signifcant concentrations of orthomagmatic nickel sulphide were discovered by Diamond Fields Resources (DFR) at Voisey’s Bay. Due to the great time span between crust formation andfnal intrusive activity (ca. 3.9 Ga to 1.27 Ga),there were, however, numerous metallogenic events within the NP.The NP was intruded by the ca. 1.3 Ga to1.2 Ga Nain Plutonic Suite (NPS) composite anorthosite-granite complex. The NPS dividesthe NP into the southern Hopedale Block (90 km by 150 km) and the northern SaglekBlock (375 km long by =50 km wide). These two blocks appear to represent two distinct Archean cratonic nuclei, each with its own distinct metallogenic history. The NPS is a coalesced assemblage of composite intrusions which include anorthosite, troctolite, norite, gabbro and granite.The Hopedale Block contains the Hunt River and Florence Lake greenstone belts, and the Weekes Amphibolite which represents remnantsf the older Hunt River greenstone belt. Geologically, these belts have some potential to host komatiitic Kambalda-style nickel, volcanogenic massive sulphide (VMS) and meso -thermal lode gold mineralization. The unconformity between Paleoproterozoic cover sequences and the trondhjemite-tonalite-granodiorite (TTG)suite which engulfed the greenstones was the locus for lead-zinc-bearing quartz-carbonate veins. Minor fracture-hosted uraninite showings are also present in the TTG.The Saglek Block is a high-grade gneissterrane with deformed Archean supracrustal sequences but no greenstone belts. Within the gneiss are variably-sized enclaves that range in composition from anorthositic to ultramafic; some of these latter xenoliths contain abun-dant fuchsite. There are also three small anorthositic to ultramafic meta-igneous complexes present in the gneiss near Okak Bay.Some Archean meta sedimentary and maficgneiss supracrustal sequences contain iron-oxide and sulphide members. The sulphide-bearing Tasiuyak parag neiss defines the cra-tonic suture between the NP and Churchill(Rae) Province. Along the cratonic suture between the NP and Churchill Province from Ramah Bay north are remnants of the Archean(or Paleoproterozoic) Hutton Anortho site Suite. Ultramafc layers within the suite contain chromite and elevated Ni values.Three ca. 2.0 Ga supracrustal sequenceswere deposited in small fault-bounded basins within the NP. The Snyder Group contains pyrrhotitiferous massive sulphide horizons. TheMugford Group contains SEDEX-like massive sulphide blocks in a debris fow and ultramafic sills with unusual PGE concentrations; alaskitic granite cutting basement gneiss to the group contains stockwork-like pyritiferous quartz veins. The Ramah Group contains numerous MVT-style zinc-lead sulphide occurrences.The Reid Brook Intrusion of the NPS contains enormous and high-grade nickel-copper-cobalt massive sulphide bodies at the Voisey’s Bay deposit. Exploration in the northern portions of the NPS in 1995 has indicated the presence of other potentially economic nickel sulphide horizons."

Jan 1, 1996

By Mario Bergeron

L&apos;exploration géologique pour les EOP (EOP: platine, palladium, iridium, osmium, ruthénium, rhodium) requiert avant tout des méthodes appropriees à la mesure de ces élémenIs. L&apos;approche analytique choisie doit tenir compte de plusieurs facteurs, les plus importants étant: le type de materiel analysé, sa representativite, la sensibitite de la methode et les cotits reliés à son utilisation. Dans cette optique, plusieurs démarches ana/ytiquessont possibles, toutes requérant une étape de préconcentration. L &apos;une des plus adéquate consiste à effectuer une préconcentration par fusion plombeuse suivie d&apos;une analyse par émission au plasma, cette procédure permettant de mesurer Ie platine, la palladium et Ie rhodium à des couts compétitifs (15 $/échantillon). Advenant 10 presence de teneurs appréciables de l&apos;un ou plusieurs de ces éléments, une préconcentration par fusion au sulfure de nickel suivie d &apos;une analyse par activation neutronique assure alors la mesure de tous les EGP ainsi que celie de l’or (90 $/échantillon). Il est important de noter que Ie nickel, ades teneurs superieures à 4%, interfère au cours de l&apos;étape de préconcentration par fusion plombeuse, ce qui se traduit pas sous-dosage des concentrations en platine, effectivement presentes dans l&apos;échantillon. Ainsi, les géologues à la recherche d&apos;EPG dans des environnements géologiques riches en nickel devraient s&apos;assurer que l&apos;analyse utilise, au cours de l&apos;étape de préconcentration, une fusion au sulfure de nickel.

Jan 1, 1990

By John Wilson

"The unconformity beneath 75 per cent or over 6000 km2 of the Athabasca Basin in Alberta lies within economically exploitable depths. The basement beneath this unconformity consists of an extension of the Wylie Lake Pluton, locally faulted and containing areas of mylonitic rocks. While the rocks of the Wylie Lake Pluton are not promising host rocks for uranium ore deposits, the areas of mylonites, graphitic rocks and possible remnants of granitegneiss would bear closer examination. One area of maficmylonites shows a weathering zone enriched in Si, Ca, Na, Pb, Ni, Ba, Co, Sr, Zn and U in addition to reported values of 0.08 oz/ton gold. This zone occurs beneath 800 m to 900 m of Athabasca Group sediments, but similar rock types are present beneath much thinner cover elsewhere. Detailed geophysical exploration is required over the area of thinner Athabasca Group rocks to define more precisely the areas of promising basement rock type.IntroductionThe Athabasca Basin in Alberta has considerable economic potential which has not yet been realized. The geological setting is closely analogous to parts of the basin in Saskatchewan which host major uranium deposits. Recent advances in geophysical techniques have led to deposits being located in Saskatchewan below 600 m of cover. This means that the unconformity between the Athabasca Group and the basement lies at exploitable depths over 6000 km2 or 75 per cent of the Alberta portion of the basin. Much of this area was only cursorily examined almost a decade ago. In addition, Alberta&apos;s new Metallic Mineral Regulations have clarified the regulatory situation in the area, and opened up much land for exploration. This article is based on Wilson&apos;s (1985a) study of the Athabasca Group and Wilson&apos;s (1986) work on the basement and alteration beneath the Athabasca Group in Alberta."

Jan 1, 1987