Search Documents

By A. B. C. Stothart

"IntroductionIn the past four years Ontario Mines have made great progress in the development of reliable mine conveyance safety dogs. History shows that, prior to 1945, a rope failure on a descending conveyance was usually followed by unsatisfactory safety dog operation.It is proposed in this paper to discuss briefly;The history of this development. Progressive .development of one type (E. Long).Free fall testing of safety dogs. Anti-trailing rope device.HistoryOn February 2nd., 1945, a hoisting rope broke at the Paymaster mine. The safety dogs proved ineffective and permitted the cage to crash through to the bottom of the shaft, with disastrous results.Following this accident, the Ontario Government appointed a Technical Committee to investigate The Safety of Hoisting Equipment and Hoisting Practice in Ontario Mines. This Committee consisted of Dr. C. R. Young (Chairman) and Professors T. R. Loudon, E. A. Allcut, V. G. Smith, and Lloyd M. Pidgeon. The Ontario Mining Association (at the request of the Ontario Government) also appointed a Committee consisting of Messrs. R. E. Dye, R. D. Parker, and R. L. Healy."

Jan 1, 1950

By J. S. Redpath

There appears to a definite trend toward the hoisting of greater tonnages from greater depths. There is every indication that this trend will continue and we feel that improvements in the design, fabrication and installation of mine guides will be of significant importance in the future. The present state of the art in mine-shaft guide systems is reviewed and the parameters required for improvement are derived in this paper. Finally, a proposal is made for a new steel guide system which meets the parameters and is economical to fabricate and install.

Jan 1, 1977

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By A. L. Mackie

Arsenic is a highly toxic element and a known human carcinogen. It is often a contaminant in mine water discharges, particularly from gold mining and roasting operations, and has been found at concentrations as high as 4 g/L. Increasingly stringent controls on the concentration of arsenic allowed to be discharged into the environment cannot always be met by current treatment processes and thus enhanced technologies are required to achieve low treated effluent concentrations at reasonable costs. A novel two-step physicochemical treatment process was developed and tested at the bench-scale using synthetic mine water solutions (SMWs) in order to reduce arsenic concentrations in treated effluent to exceed current discharge regulations. The process includes chemical coagulation with ferric sulphate and ballasted flocculation for enhanced solid-liquid separation. The SMW contained 59 ± 2 mg/L arsenic with a slightly alkaline pH. The effect of arsenic speciation on the process was tested by using either arsenite, As(III), or arsenate, As(V), in the SMW solutions. Tests were performed at cold temperature (3 ± 1 °C) to ensure the process? efficacy year-round in northern climates. Arsenic in As(V) SMW solutions was removed to a final total concentration of 0.0054 ± 0.002 mg/L, almost half the current recommended allowable drinking water concentration of 0.010 mg/L. As(III) was removed to a concentration below the Metal Mining Effluent Regulations? (MMER) current limit of 0.50 mg/L, to 0.32 ± 0.06 mg/L, with double the coagulant dose used in Stage 1 for As(V) removal. Oxidant addition at a concentration of 5 mg KMnO4/L in Stage 2 resulted in final total arsenic concentrations of 0.017 ± 0.002 mg/L and pH adjustment with lime in Stage 2 resulted in 0.0415 ± 0.0007 mg As/L in treated As(III) SMW. Both of these modifications to the process reduced arsenic concentrations to below proposed new MMER limits (i.e., 0.10 mg/L). This two-stage treatment process was shown to reduce arsenic concentrations to well below current treatment guidelines while reducing or eliminating chemical oxidant demand.

Aug 1, 2013

By N. Kubo

Sumitomo Toyo Copper Smelter and Refinery was commenced in 1971, and its production capacity of sulfuric acid was 550tpd at the beginning. In 2001 Toyo Copper Smelter and Refinery projected to expand its copper production capacity to 450,000tpy, and now the project is still in progress. To achieve this expansion project, 4,000tpd of sulfuric acid production capacity is necessary to the acid plant. So as a part of this project, the construction of the new converting and absorbing line and the improvement of the existing converting and absorbing line were carried out from 2001 until 2005. Then the production capacity of these 2 lines has already reached the target, 4,000tpd of sulfuric acid. Moreover, at the design of the new line, we adopted several latest technologies and materials in order to construct the world's leading acid plant. Basing on the operation performance of the new line, we have improved the existing line in 2005. Both of these 2 converting and absorbing lines are working quite well and contribute to big energy saving and excellently stable operation. Cu2007

Jan 1, 2007

By C. Klinkenberg, G. Zhu, K. Hulka, S. V. Subramanian

A quantitative model based on strain accumulation in multi-pass rolling is developed to overcome a large critical strain for dynamic recrystallisation in a Nb microalloyed steel with high Mn content (HTP steel). The larger the critical strain for dynamic recrystallisation, the finer is the dynamically recrystallised grain size. The initial mill trial showed that it is feasible to achieve ultra-fine grain size by dynamic recrystallisation but the prevention of static recrystallisation in between passes is identified as an essential condition to suppress mixed grain size. The data-base on static softening kinetics at short interpass time was experimentally determined on WUMSI and incorporated in the model. The model is used to optimise the strip rolling schedule to prevent static recrystallisation in the interpass time. The rolling simulation of strip rolling schedule has validated the model prediction that it is possible to obtain a uniform ultra-fine ferrite grain size of about 1-2 micrometer diameter in final ferrite microstructure for industrial rolling parameters. A user friendly software package has been developed to apply the model for off-line control of mill processing parameters, i.e., time-temperature-deformation schedule of finish rolling in order to accumulate large strain to overcome a large critical strain for dynamic recrystallisation. The model is a powerful predictive tool for grain size control in multi-pass rolling.

Jan 1, 2004

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007

By Yve Potvin, Fabien Miller, Deni Jacob

"The potential benefits of measuring the volume of excavated open stope are enormous. By comparing the actual excavation of the orebody contour, it is possible to determine the “real"" amount of mining dilution, as well as the ore left in place. Noranda Technology Centre (NTC) has developed a stope survey system that allows for rapid and efficency measurement of underground excavation volumes. The system comprises a commercial laser (EDM), a set of lightweight rigid rods, an automated scanning device, a hand-held data logger and Autocad-based software for volume calculation and drawing manipulations. This system is an invaluable tool for the optimization of mining practices and could also be used for the delineation of caving areas. IntroductionDilution is the most common and devastating mine disease. In some instance s it could systematically cripple the profitability of an operation, and in more extreme cases, it could become a terminal disease. The Northern Miner Journal (1988) reported that many operations have closed because of uncontrolled dilution, before they even completed their first year of production. Other studies (Pakalnis, 1986) have shown that approximately 40% of all underground operations have more than 20% dilution. Considering that every ton of dilution costs in the neighbourhood of $25, the total direct cost of dilution to the Canadian mining industry may easily exceed one hundred million dollars per year.The dilution problem has been a major concern to Noranda Minerals for some time and in 1984 a comprehensive geomechanics research program was created at the Noranda Technology Centre (NTC) in Pointe-Claire, Quebec. New empirical stope dimensioning techniques, improved cable bolting techniques and sophisticated ground control instrumentation projects (among others) contributed to improve the situation at Noranda.A new tool which can have a very significant impact on the ""war"" against dilution is being developed by the Noranda Technology Centre. The laser stope survey system allows for a rapid, precise and efficient measurement of underground excavation volumes. By comparing the excavation planned with the volume excavated, it becomes possible to determine the ""real"" amount of mining dilution as well as the amount of ore left in place. This system may also allow for early detection of a dilution problem. As with other diseases, early detection provides the best chance for a fast and total recovery."

Jan 1, 1992

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By W. J. Asselstine

Introduction This paper is prepared from data gathered for a similar paper to be submitted to the United States Bureau of Mines, for publication as one of their information circulars. It covers the history and development of the present milling practice at Premier. The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by D. L. Pitt, Manager of the Premier Gold Mining Company, Limited; also their indebtedness to various members of the Engineering Staff and of the Accounting Department who have assisted materially in gathering the data used. Location The Premier mine and mill are situated in northern British Columbia, approximately fifteen miles north of the head of Portland canal, in the Salmon River section, about half a mile east of the Alaska-British Columbia boundary line where it crosses die Salmon river. The mill is located on a rather steep hillside on the horizon of the main haulage level of the mine, and is within a hundred feet of the mouth of the tunnel. Both the mine and mill are connected with tidewater at Stewart, B.C., by an aerial tramway (1) eleven and one-half miles in length, which delivers both ore and concentrate to the bunkers at the dock for shipment to the smelters. All mine and mill supplies are transported from Stewart dock to Premier over this tramway, except heavy machinery. Heavy pieces have to be hauled either by truck in summer or sleighs in winter over a good road which runs from Stewart dock to Premier.

Jan 1, 1933

By M. Mohammadijoo, J. B. Wiskel, D. G. Ivey, S. Kenny, H. Henein

Cold-wire tandem submerged arc welding (CWTSAW) has recently been developed as a novel welding technique to replace the conventional tandem submerged arc welding (TSAW) process and improve the productivity of pipeline manufacturing. The process involves two electrodes with arcs and one electrically cold electrode. Since heat-input of the welding process is a key factor affecting the properties of the weld metal (WM) and the heat-affected zone (HAZ), and the additional cold-wire affects the heat introduced to the weldment, it is of interest to investigate property and geometry changes in the WM and HAZ when a cold-wire is added to the welding process. In the current research, the CWTSAW process is investigated and optimized by correlating the main welding parameters with the micro-hardness of the WM and HAZ and the geometry of the weld, i.e., the bead width (BW), penetration depth (PD), reinforcement area (RA) and coarse grained heat-affected zone (CGHAZ) area. Three statistical and mathematical methods are employed to optimize the CWTSAW process in terms of the mechanical properties and WM and HAZ geometry of a typical microalloyed steel used for pipeline manufacturing.

Jan 1, 2015

By W. D. Breil, C. B. Ison

A collection of general performance data relating to the G.H.H. - Gutehoffnungshiitte multi-rope friction hoist will be discussed together with some aspects of the following: overspeed supervision by a pantam device as opposed to the lilly type of fly ball control, automatic control systems, multi-disc braking, generator and motor winding, constant temperature monitoring, the development of an automatic hoist-rope lubrication system, and the control of rope tensions by the installation of G.H.H. - Gutehoffnungshiitte hoist rope fine tensioning units.

Jan 1, 1972

Mine Safety in Chile ?Since the year 2000 fatality rate averages 34 per year ?1% of world mining labour force but 8% of world?s mining fatalities San Jose Mine Safety ?From 1998 to 2010 eight fatalities ?In 2003 mine inspectors recognized no second means of egress and a raise system was developed ?In 2006 182 workers were injured, 56 of them seriously ?In January 2007, there was a fatality after a rock burst, and the government ordered the mine closed ?Less than a year later the mine was back in operations. It had not complied with some of the basic safety measures ordered. One of those measures was to complete the escape way ladder.

May 1, 2011

By W. E. Cockfield

THE object of this paper is to review recent geological work in the Cariboo district and to present notes on the recent development of mineral properties. The Geological Survey has done considerable work in the Cariboo district, extending over a period of years. In 1885 and 1886, Bowman (1) mapped the geology of a large area. In 1922 and 1923, Johnston and Uglow (2) mapped Barkerville area in some detail and prepared a report on the placer and lode gold deposits. In 1931 and 1932, Cockfield and Walker (3) mapped the Quesnel Forks area. In 1933, Hanson reported on Willow River area ( 4), and in 1934 made a detailed examination of part of the Barkerville area (5). In 1935, Lang commenced work on the Keithley area, lying to the southeast of the Barkerville area, and in 1936 published a preliminary re-port (6). The work on Keithley area was continued in 1936 by both authors of the present paper. As the results of the earlier work have been published, this paper will be concerned largely with Keithley area, that is, the part of the region lyinp between longitudes 121° 00' and 121° 30', and latitudes 52° 45' and 53° 00 . This area lies astride Cariboo (Swamp) river and extends north some 17 miles from Keithley, which is situated near the southern border of the map-area (see sketch-map). Points in the western part of the map-area are fairly accessible. A road extends from Barkerville to upper Cunningham creek, and from this a trail crosses Snowshoe plateau to Keithley. A second trail from this road leads to the lower falls on Cariboo river. From this road, a branch road leads to upper Antler creek, with a trail leading from this branch road to Keithley. Part of this western half of the area is made up of the Snowshoe plateau, which constitutes a gently rolling surface, at or above timber line, where trails are largely unnecessary.

Jan 1, 1937

By L. E. Djingheuzian

"IntroductionDURING the past two decades an enormous amount of empirical data has been accumulating on grinding. These data have been obtained by mill operators on grinding ores with a diversity of characteristics, and generally they have been published. However, whenever an operator, who has started milling on a new ore, has tried to find a case in literature which would exactly fit his particular grinding problem, he has failed. Evidently, something fundamental has been lacking in all these empirical data, and, as a consequence, each new operator has had to undertake his own experimenting, get the best results he can, maybe publish these results, and let it go at that. This, in the writer's opinion, has been• due to the fact that even the ablest and most inquisitive millman has been forced to look on grinding as an art, and so, except very rarely, has not been able to find the time to stop and think; if he did so, it was rather in a philosophic way, that grinding is a fundamental process, a process that takes place in river beds, on the sea shore, etc.Nevertheless, when all the data so far published are correlated and examined as a whole, one is struck with the advances that have been made in grinding. The writer (7) had made such a study in 1949, and, when the correlation was completed, it showed that there was nothing heterogeneous about the accumulated data and that when brought together they were in harmony with each other. The writer's conclusion was that, if grinding criteria were defined and were expressed in such a way as to make integration of any data into basic formulae possible, grinding would be established as a mathematically exact science, and grinding worries of the harassed mill operator would be at an end!The first attempts to rationalize comminution were made by Rittinger and Kick. However, their theories led to endless disputes which did not accomplish much, except possibly clearing the path for subsequent investigators."

Jan 1, 1952

By D. H. Pulling

Statistics for copper consumption from various sources show that the importance of production from secondary sources is increasing. This is of particular significance in countries such as the U.K ., which are totally dependent on secondary material for the supply of home-produced copper . A brief survey of the U.K . industry has shown that, in the past, relatively high profit margins have not encouraged high cap ital investment and development of more sophisticated operating techniques, but set against a background of rapidly escalating operating and energy costs , together with an ever-increasing demand for copper , it is anticipated that the industry will see great changes in the near future. With this in mind, an experimental furnace for continuous smelting of copper-bearing scrap has been developed at the University of Birmingham. This furnace has been designed to combine the conventional operations of blast furnace or reverberatory smelting, usually followed by converting, in one unit, and incorporates many of the features of the WORGRA and Noranda processes for continuous primary smelting . It consists of a long, sloping channel, constructed of chrome-magnesite refractory, which: is churned near the top. Smelting is effected lower down the channel, where iron, etc., in the scrap is oxidized and slagged off with silica flux. Provision is made for oil injection to increase oxidation rates. Metal can flow from the bottom of the channel, and slag from the top, so that a counter-current flow is achieved. The approximate molten capacity is 25 kg. Various scrap charges, both synthetically made and as supplied from various industrial smelters, have been successfully smelted. Metal of 83 -95 % Cu has been produced, depending on the original charge composition and the degree of air injection, although air injection was also found to considerably increase the copper loss to slag. Recoveries of other valuable non-ferrous metals in the charge were good.

Jan 1, 1977

By E. Engelbrecht

"A pressure non-oxidative leach is employed at Anglo American Platinum Base Metal Refiners to extract nickel from a slow cooled matte. The design base requires two 80 m3 autoclaves in parallel to achieve a nickel extraction of 60% at the nameplate capacity of 32.4 ktpa nickel plated. Isothermal modelling of mineralogical and chemical concentration profiles, through a reactive mass balance, permitted rate constant parameter estimation and selection of the most probable reaction pathway. The model was validated with plant data up to a capacity of 26 ktpa Ni plated and suggested by extrapolation that nameplate capacity may be viable through one 80 m3 autoclave.INTRODUCTION Anglo American Platinum Base Metal Refiners is situated on the outskirts of Rustenburg in the North-West province of South-Africa. The refinery produces nickel cathode, copper cathode, cobalt sulphate powder, covellite rich copper pressure leach residue and bulk sodium sulphate through an integrated circuit that refines slow cooled converter matte. The converter matte is milled, non-magnetics are separated as solid nickel copper matte (NCM), and the magnetics are leached yielding a pressure vessel liquor (PVL). The remaining solid platinum group metals (PGM) concentrate after leaching is sent for downstream processing in the Precious Metals Refinery (Hofirek & Kerfoot, 1992). The work presented here is applicable to the base metals refinery which receives the two base metals feed stocks NCM and PVL. In 2009 the capacity of the refinery was upgraded from 21 ktpa nickel cathode plated to 32.4 ktpa. This paper deals with evaluating the capacity of the pressurised non-oxidative nickel leach (NOX) process which accounts for at least 28% of the nickel leached from NCM by design. The NOX design base requires two 80 m3 autoclaves divided into four compartments operated in parallel at 155°C and 600kPa(g). Elevated temperature is required to speed up the leach kinetics of particularly nickel and iron which are trapped in slow leaching mineralogical phases namely millerite and bornite, (Dinham, 2006). The stated equivalent capacity for the NOX configuration was 32.9 ktpa nickel plated at first pass nickel and iron leach efficiencies of 60% and above 80% respectively and is a key step for the selective removal of iron (Bryson, Hofirek, Collins, Stiksma, & Bereaowsky, 2008)."

Jan 1, 2017

By Reis. E., P. Pino Véliz

"Along the process of defining the fundamentals of a ferronickel project, several questions require proper answers from the very beginning such as the size and characteristics of the laterite deposit (oxide or silicate), the mineralogical variability, and the selection of the most valuable process route. In general, these elements will be defined along the progress of the exploration and feasibility studies, and definitive engineering. Also, from the very preliminary estimates, three questions are very common: what should be the plant capacity (annual tonnes of contained nickel), what will be the probable capital required (CAPEX), and what will be the estimated timeline (schedule) between the initial stage, say the feasibility study and the plant start-up and ramp-up to designed capacity. The accuracy of the capital cost estimates also progresses along the different stages of development from ±50% at the Preliminary Economic Assessment (PEA) stage down to ±5% for the Detailed Engineering and Construction stage. These accuracies of estimates have been, in some ways, accepted by the mining community and investors. The industry accepted benchmark for ferronickel projects in terms of CAPEX are then in the order of US$50,000 per tonne of nickel contained in the FeNi product. In this paper, the authors analyze in some details three ferronickel projects for lateritic ores that have selected the Rotary Kiln - Electric Furnace (RKEF) as the suitable technological route and have started production in the period 2006–2016. Some key aspects of the ferronickel projects are examined: 1) size and type of deposit; 2) flowsheet selection; 3) evolution of capital cost as a function of capacity from the feasibility stage to construction; 4) comparison between planned production scale and actual ramp up; 5) estimated capital expenditure (CAPEX) compared with actual figures; 6) nickel price evolution and timing of the approval for the project to proceed to construction and production start-up. The objective of this paper is to identify key elements that should be addressed in future projects and that are proposed as benchmark figures for similar projects."

Jan 1, 2017